Industrial 5G NR Cellular Gateway ICG-2515-NR series Industrial 5G NR Cellular Gateway ICG-2515-NR Series -1-
Industrial 5G NR Cellular Gateway ICG-2515-NR series Copyright Copyright (C) 2021 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Industrial 5G NR Cellular Gateway ICG-2515-NR series – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. CE mark Warning The is a class A device, In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Table of Contents Chapter 1. Product Introduction............................................................................................. 7 1.1 Package Contents ...................................................................................................... 8 1.3 Overview .................................................................................................................... 9 1.4 Features ...................................
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.6 4.7 4.8 4.9 4.5.3 WAN Advanced ...................................................................................... 69 4.5.4 LAN Setup.............................................................................................. 70 4.5.5 Multi-Subnet ........................................................................................... 71 4.5.6 Routing..................................................................................
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.16 Upload Map.......................................................................................... 114 4.10 Wireless ................................................................................................................. 115 4.10.1 2.4G WiFi ............................................................................................. 116 4.10.2 5G WiFi ................................................................................
Industrial 5G NR Cellular Gateway ICG-2515-NR series Chapter 1. Product Introduction Thank you for purchasing PLANET Industrial 5G NR Cellular Gateway, ICG-2515-NR Series. The descriptions of these models are as follows: ICG-2515-NR Industrial 5G NR Cellular Gateway with 5-Port 10/100/1000T ICG-2515W-NR Industrial 5G NR Cellular Wireless Gateway with 5-Port 10/100/1000T “Cellular Gateway” mentioned in the manual refers to the above models.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 1.3 Overview Powerful 5G NR and Wi-Fi 6 Industrial Networky Solution PLANET ICG-2515-NR series is an industrial-grade wireless cellular gateway for demanding mobile applications, M2M (machine-to-machine) and IoT deployments. Upgraded to the latest cellular technology of 5G NR (new radio), the ICG-2515-NR series is able to provide ultra-fast broadband access with 5G cellular network.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Ultra-Fast Speed 4G/5G Network* The ICG-2515-NR series supports 5G NR DL speeds higher than 2.4 Gbps and 4G LTE DL speeds of up to 1 Gbps. The wide spectrum bandwidth accelerates internet speeds and reduces network latency for premium and time-sensitive connectivity services. The ICG-2515-NR series also supports multi-band connectivity including LTE FDD/TDD, WCDMA and GSM for a wide range of applications.
Industrial 5G NR Cellular Gateway ICG-2515-NR series GPS Included The ICG-2515-NR series is equipped with (global positioning system) feature. It adapts 5G-NR technology to incorporate multiple global navigation systems (GPS/GLONASS/BeiDou/Galileo/QZSS). It helps to position location of cellular gateway based on a network of satellites that continuously transmits necessary data.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Wi-Fi Deployments and Authentication with Simplified Management The ICG-2515-NR series also provides a built-in AP Controller, Captive Portal, RADIUS and a DHCP server to facilitate small and medium businesses to deploy secure employee and guest access services without any additional server. The ICG-2515-NR series can offer a secure Wi-Fi network with easy installation for your business.
Industrial 5G NR Cellular Gateway ICG-2515-NR series For example, to configure multiple Smart APs of the same model, the ICG-2515-NR series allows clustering them to a managed group for unified management. According to requirements, wireless APs can be flexibly expanded or removed from a wireless AP group at any time. The AP cluster benefits bulk provision and bulk firmware upgrade through single entry point instead of having to configure settings in each of them separately.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 1.4 Features Key Features • Global 5G NR (NSA/SA)/4G LTE network with dual SIM design for cellular network redundancy • Automatic failover between 5G NR and Gigabit WAN • Complies with IEEE 802.11ax and IEEE 802.
Industrial 5G NR Cellular Gateway ICG-2515-NR series IP Routing Feature • Static Route • Dynamic Route • OSPF Firewall Security • Cybersecurity • Stateful Packet Inspection (SPI) firewall • Blocks DoS/DDoS attack • Content Filtering • MAC Filtering and IP Filtering • NAT ALGs (Application Layer Gateway) • Blocks SYN/ICMP Flooding VPN Features • IPSec/Remote Server (Net-to-Net, Host-to-Net), GRE, PPTP Server, L2TP Server, SSL Server/Client (Open VPN) • Max.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Others • Setup wizard • Dashboard for real-time system overview • Supported access by HTTP or HTTPS • Auto reboot • PLANET NMS System and Smart Discovery Utility for deployment management • Planet CloudViewer App for real-time monitoring - 16 -
Industrial 5G NR Cellular Gateway ICG-2515-NR series 1.5 Product Specifications Models ICG-2515W-NR ICG-2515-NR Hardware Specifications 5 10/100/1000BASE-T RJ45 Ethernet ports including Copper Ports 3 LAN ports (Ports 1 to 3) 1 LAN/WAN port (Port 4) 1 WAN port (Port 5) Serial Interface RJ45 serial port SIM Interface 2 SIM card slots with mini SIM card tray Cellular Antenna 5 dBi external antennas with SMA connectors for 5G-NR 2 Digital Input (DI): Level 0: -24V~2.1V (±0.1V) Level 1: 2.1V~24V (±0.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 2.4G(Green), 5G(Green) Multi Band Supports 5G NR LTE-FDD n1/n2/n3/n5/n7/n8/n12/n20/n25/n28/n38/n40/n41/n48/n66/n71/n77/n78/n79 B1/B2/B3/B4/B5/B7/B8/B12/B13/B14/B17/B18/B19/B20/B25/B26/B28/B29/B30/ B32/B46/B66/B71 LTE-TDD B34/B38/B39/B40/B41/B42/B43/B48 WCDMA B1/B2/B3/B4/B5/B8 GNSS GPS L1+L5 dual bands/GLONASS/BeiDou/Galileo/QZSS Data Transmission Throughput 2.4Gbps (DL)/500Mbps (UL) for NR 1Gbps (DL)/200Mbps (UL) for LTE 42Mbps (DL)/5.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 1200 Mbps* for 5 GHz *The estimated transmission distance is based on the theory. The actual distance will vary in different environments. 11b: 23dbm+/- 1.5dbm @11Mbps 11g: 20dbm+/- 1.5dbm @54Mbps 11g/n: 20dBm +/- 1.5dbm @MCS7, HT20 17dBm@MCS7,HT40 11a: 19.5dBm +/- 1.5dbm @54Mbps 11a/n: 19.5dBm+/- 1.5dbm @MCS7, Transmission Power HT20 17dBm@MCS7, HT40 11ac HT20: 20+/-1.5dBm @MCS8 11ac HT40: 17+/-1.5dBm @MCS9 11ac HT80: 14.5+/-1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series PLANET Smart Discovery utility and NMS controller supported Secure Management SSHv2, TLSv1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Chapter 2. Hardware Introduction 2.
Industrial 5G NR Cellular Gateway ICG-2515-NR series LED Definition: System LED Color Function P1 Green Lights to indicate DC power input 1 has power. P2 Green Lights to indicate DC power input 2 has power. Alarm Red Lights to indicate that power or port has failed. I/O Red Lights to indicate that power or port has failed or DI has event. SIM1 Green Lights to indicate the SIM1 is connecting successfully. SIM2 Green Lights to indicate the SIM2 is connecting successfully. 2.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 2.2 Hardware Installation Refer to the illustration and follow the simple steps below to quickly install your Cellular Gateway. 2.2.1 SIM Card Installation A. Insert an ejector pin into the yellow button next to the tray to loosen the tray. B. Pull out the tray gently from the tray slot. Place the SIM card on the tray with the gold-colored contacts facing upwards. C. Insert the tray back into the tray slot..
Industrial 5G NR Cellular Gateway ICG-2515-NR series 2.2.2 5G NR Antenna Installation Step 1: Connect 5G NR antennas to the 5G NR antenna extension. Step 2: Fasten the 5G NR antenna extensions to the connectors. 2.2.3 Wi-Fi Antenna Installation Step 1: Fasten the two dual-band antennas to the antenna connectors on the front panel of the Cellular Gateway. Step 2: You can bend the antennas to fit your actual needs.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 3.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Cellular Gateway is used for two DC redundant power inputs. Please follow the steps below to insert the power wire. When performing any of the procedures like inserting the wires or tightening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock. 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series The wire gauge for the terminal block should be in the range between 12 and 24 AWG. CAUTION PWR1 and PWR2 must provide the same DC voltage while operating with dual power input. 3.5 Grounding the Device User MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. EMD (Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY. 3.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Chapter 3. Preparation Before getting into the device’s web UI, user has to check the network setting and configure PC’s IP address. 3.1 Requirements User is able to confirm the following items before configuration: 1. Please confirm the network is working properly; it is strongly suggested to test your network connection by connecting your computer directly to ISP. 2. Suggested operating systems: Windows 7 / 8 / 10. 3.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 3.2 Setting TCP/IP on your PC The default IP address of the cellular gateway is 192.168.1.1, and the DHCP Server is on. Please set the IP address of the connected PC as DHCP client, and the PC will get IP address automatically from the VPN cellular gateway Please refer to the following to set the IP address of the connected PC. Windows 7/8 If you are using Windows 7/8, please refer to the following: 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 2. Click "Change adapter settings". 3. Right-click on the Local Area Connection and select Properties.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties or directly double-click on Internet Protocol Version 4 (TCP/IPv4).
Industrial 5G NR Cellular Gateway ICG-2515-NR series 5. Select "Use the following IP address" and "Obtain DNS server address automatically", and then click the “OK” button.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Windows 10 If you are using Windows 10, please refer to the following: 1. In the search box on the taskbar, type “View network connections”, and then select View network connections at the top of the list.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 2. Right-click on the Local Area Connection and select Properties. 3. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties or directly double-click on Internet Protocol Version 4 (TCP/IPv4).
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4. Select "Use the following IP address" and "Obtain DNS server address automatically", and then click the “OK” button.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 3.3 Planet Smart Discovery Utility For easily listing the cellular gateway in your Ethernet environment, the search tool -- Planet Smart Discovery Utility -- is an ideal solution. The following installation instructions are to guide you to running the Planet Smart Discovery Utility. 1. Download the Planet Smart Discovery Utility in administrator PC. 2. Run this utility as the following screen appears.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 1. This utility shows all necessary information from the devices, such as MAC address, device name, firmware version, and device IP subnet address. It can also assign new password, IP subnet address and description to the devices. 2. After setup is completed, press the “Update Device”, “Update Multi” or “Update All” button to take effect.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Chapter 4. Web-based Management This chapter provides setup details of the device’s Web-based Interface. 4.1 Introduction The device can be configured with your Web browser. Before configuring, please make sure your PC is under the same IP segment with the device. 4.2 Logging in to the Cellular Gateway Refer to the steps below to configure the cellular gateway: Step 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.3 Main Web Page After a successful login, the main web page appears. The web main page displays the web panel, main menu, function menu, and the main information in the center. Main Menu Web Panel Figure 4-3-1: Main Web Page Function Menu ■ Web Panel The web panel displays an image of the device’s ports as shown in Figure 4-3-2. Figure 4-2: Web Panel Object Icon Function To indicate the LAN with the RJ45 plug-in.
Industrial 5G NR Cellular Gateway ICG-2515-NR series ■ Main Menu The main menu displays the product name, function menu, and main information in the center. Via the Web management, the administrator can set up the device by selecting the functions those listed in the function menu and button as shown in Figures 4-3-2 and 4-3-3.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4 System Use the System menu items to display and configure basic administrative details of the cellular gateway The System menu shown in Figure 4-4-1 provides the following features to configure and monitor system. Figure 4-4-1: System Menu Object Wizard Description The Wizard will guide the user to configuring the cellular gateway easily and quickly. Dashboard The overview of system information includes connection, port, and system status.
Industrial 5G NR Cellular Gateway ICG-2515-NR series RADIUS Enable/Disable RADIUS on cellular gateway Captive Portal Enable/Disable Captive Portal on cellular gateway SNMP Display SNMP system information NMS Enable/Disable NMS on cellular gateway Remote Syslog Enable Captive Portal on cellular gateway Event Log Display Event Log information - 41 -
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.1 Setup Wizard The Wizard will guide the user to configuring the cellular gateway easily and quickly. There are different procedures in different operation modes. According to the operation mode you switch to, please follow the instructions below to configure the cellular gateway via Setup Wizard as shown in Figure 4-4-2.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Description Enter the IP address of your cellular gateway The default is IP Address 192.168.1.1. An address code that determines the size of the network. Normally Subnet Mask use 255.255.255.0 as the subnet mask. By default, the DHCP Server is enabled. DHCP Server If user needs to disable the function, please uncheck the box. By default, the start IP address is 192.168.1.100.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Step 4: WAN Interface The cellular gateway supports two access modes on the WAN side shown in Figure 4-4-6 Figure 4-4-6: Setup Wizard – WAN Configuration Mode 1 -- Static IP Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter the IP Address, Netmask, Default Gateway and DNS Server provided to you by your ISP.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Default Gateway Enter the Gateway assigned by your ISP. DNS Server The DNS server information will be supplied by your ISP. Next Press this button for the next step. Previous Press this button for the previous step. Press this button to undo any changes made locally and revert to Cancel previously saved values. Mode 2 -- DHCP Client Select DHCP Client to obtain IP Address information automatically from your ISP.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-4-9: Setup Wizard –Security Setting Object Description 2.4G Wireless Status Allows user to enable or disable 2.4G WiFi Wireless Name (SSID) It is the wireless network name. The default 2.4G SSID is “PLANET_2.4G” Hide SSID Allows user to enable or disable SSID Bandwidth Select the operating channel width, “20MHz” or “40MHz” Channel It shows the channel of the CPE. Default 2.4GHz is channel 6.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Set up the Security Settings as shown in Figure 4-4-10. Figure 4-4-10: Setup Wizard –Security Setting Object Description The SPI Firewall prevents attack and improper access to network SPI Firewall resources. The default configuration is enabled. SYN Flood is a popular attack way. DoS and DDoS are TCP Block SYN Flood protocols. Hackers like using this method to make a fake connection that involves the CPU, memory, and so on.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Step 5: Setup Completed The page will show the summary of LAN, WAN and Security settings as shown in Figure 4-4-11. Figure 4-4-11: Setup Wizard –Setup Completed Object Description Finish Press this button to save and apply changes. Previous Press this button for the previous step.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.2 Dashboard The dashboard provides an overview of system information including connection, port, and system status as shown in Figure 4-4-12.
Industrial 5G NR Cellular Gateway ICG-2515-NR series WAN/LAN Connection Status Object Description The status means WAN is connected to Internet and LAN is connected. The status means WAN is disconnected to Internet and LAN is connected. The status means WAN is connected to Internet and LAN is disconnected. Port Status Object Description Ethernet port is in use. Ethernet port is not in use. USB port is in use. USB port is not in use.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Wireless Status Object Description Wireless is in use. Wireless is not in use. 4.4.3 System Status This page displays system status information as shown in Figure 4-4-13.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-4-13: System Status - 52 -
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.5 System Service This page displays system service information as shown in Figure 4-4-14.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.7 Statistics This page displays the number of packets that pass through the cellular gateway on the WAN and LAN. The statistics are shown in Figure 4-4-15.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.8 Connection Status The page will show the DHCP Table and ARP Table. The status is shown in Figure 4-4-16.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.9 High Availability High Availability (HA) is a system redundant that two cellular gateway of ICG-2515-NR series can be set up in a master/slave configuration. The master cellular gateway provides the Internet connection but, in the case of hardware or WAN connectivity failure, the slave (backup) cellular gateway automatically takes over Internet connection. It provides redundant hardware and software that make the system available despite failures.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.10 RADIUS Remote Authentication Dial-In User Service (RADIUS) is a security authentication client/server protocol that supports authentication, authorization and accounting. The RADIUS Server page is shown in Figure 4-4-18. Figure 4-4-18: RADIUS Server Object Description Disable or enable the RADIUS function. RADIUS The default configuration is disabled.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.11 Captive Portal Captive portal service gives the ability to organize a public (or guest) Wi-Fi zone with user authorization. A captive portal is the authorization page that forcibly redirects users who connect to the public network before accessing the Internet. The Captive portal page is shown in Figure 4-4-20. Figure 4-4-20: Captive portal Object Captive portal Description Disable or enable the Captive portal function.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.12 SNMP This page provides SNMP setting as shown in Figure 4-4-21. Figure 4-4-21: SNMP Object Enable SNMP Description Disable or enable the SNMP function. The default configuration is enabled.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.13 NMS The ICG-2515-NR series can support both NMS controller and CloudViewer Sever for remote management. PLANET's NMS Controller is a Network Management System can monitor all kinds of deployed network devices, such as managed switches, media converters, routers, smart APs, VoIP phones, IP cameras, etc., compliant with the SNMP Protocol, ONVIF Protocol and PLANET Smart Discovery utility.
Industrial 5G NR Cellular Gateway ICG-2515-NR series The CloudViewer Server – Internet screens in Figure 4-4-24 appear.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.14 Fault Alarm This page provides fault alarm setting as shown in Figure 4-4-25. Figure 4-4-25: Fault Alarm Object Description • Enable Controls whether Fault Alarm is enabled • Record Controls whether Record is sending System log or SMS • Event Controls whether Port Fail or Power Fail or both for fault detecting. • Power Alarm Controls whether PWR1 or PWR2 or both for fault detecting.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.15 Digital Input / Output This page provides Digital Input / Output setting as shown in Figure 4-4-26. Figure 4-4-26: Digital Input / Output Object Description • Enable Check the Enable checkbox to enable Digital Input / output function. Uncheck the Enable checkbox to disable Digital input / output function. • Condition As Digital Input: Allows user to select High to Low or Low to High.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Allows user to monitor an alarm from port failure, power failure, Digital Input 0 (DI 0) and Digital Input 1(DI 1) which means if Digital Output has detected these events, then Digitial Output would be triggered according to the setting of Condition. • Power Alarm Allows user to choose which power module that needs to be monitored. • Port Alarm Allows user to choose which port that needs to be monitored.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.4.16 Remote Syslog This page provides remote syslog setting as shown in Figure 4-4-27.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.5 Network The Network function provides WAN, LAN and network configuration of the cellular gateway as shown in Figure 4-5-1. Figure 4-5-1: Network Menu Object Description Priority Allows setting priority of WAN interface. WAN Allows setting WAN interface. WAN Advanced Allows setting WAN Advanced settings. LAN Allows setting LAN interface. Multi-Subnet Allows setting Multi-Subnet1 ~ Subnet4 interface.
Industrial 5G NR Cellular Gateway ICG-2515-NR series The default configuration is disabled. Routing RIP OSPF IGMP Allows setting Route. Disable or enable the RIP function. The default configuration is disabled. Disable or enable the OSPF function. The default configuration is disabled. Disable or enable the IGMP function. The default configuration is disabled. IPv6 Allows setting IPv6 WAN interface. DHCP Allows setting DHCP Server. DDNS Allows setting DDNS and PLANET DDNS.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.5.2 WAN This page is used to configure the parameters for Internet network which connects to the WAN port of the cellular gateway as shown in Figure 4-5-3. Here you may select the access method by clicking the item value of WAN access type. Figure 4-5-3: WAN Object Description Please select the corresponding WAN Access Type for the Internet, and fill out the correct parameters from your local ISP in the fields which appear below.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Description Enter the Subnet Mask assigned by your ISP. Gateway Enter the Gateway assigned by your ISP. DNS Server The DNS server information will be supplied by your ISP. DHCP Select DHCP Client to obtain IP Address information automatically from your ISP. WAN IP, whether obtained automatically or specified manually, should NOT be on the same IP net segment as the LAN IP; otherwise, the cellular gateway will not work properly.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Load Balance Weight External Connection Detection Detect Interval Description Load Balance Weight allows you to set a relative weight (from 1 - 10) for each WAN port. Enable to detect the status of WAN connection. Set the detect interval as you need. The recommended value is 5 (default). Detect Link Up Set the times for detecting link up. Threshold The recommended value is 8 (default). Detect Link Down Set the times for detecting link down.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.5.5 Multi-Subnet This page provides multi-subnet setting as shown in Figure 4-5-6. Figure 4-5-6: Multi-Subnet 4.5.6 Routing Please refer to the following sections for the details as shown in Figures 4-5-7 and 4-5-8.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-5-8: Routing setup Routing tables contain a list of IP addresses. Each IP address identifies a remote cellular gateway (or other network gateway) that the local cellular gateway is configured to recognize. For each IP address, the routing table additionally stores a network mask and other data that specifies the destination IP address ranges that remote device will accept. Object Description There are two types: Host and Net.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.5.7 WAN IPv6 Setting This page is used to configure parameter for IPv6 internet network which connects to WAN port of the cellular gateway as shown in Figure 4-5-9. It allows you to enable IPv6 function and set up the parameters of the cellular gateway’s WAN. In this setting you may change WAN connection type and other settings. Figure 4-5-9: IPv6 WAN setup Object Description Connection Type Select IPv6 WAN type either by using DHCP or Static.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-5-10: DHCP Object Description By default, the DHCP Server is enabled, meaning the cellular DHCP Service gateway will assign IP addresses to the DHCP clients automatically. If user needs to disable the function, please set it as disable. Start IP Address By default, the start IP address is 192.168.1.100.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.5.9 DDNS The cellular gateway offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address, and then your friends can connect to your server by entering your domain name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as PLANET DDNS (http://www.planetddns.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-5-11: PLANET DDNS Object DDNS Service Interface Description By default, the DDNS service is disabled. If user needs to enable the function, please set it as enable. User is able to select the interface for DDNS service. By default, the interface is WAN 1. There are three options: DDNS Type 1. PLANET DDNS: Activate PLANET DDNS service. 2. DynDNS: Activate DynDNS service. 3. NOIP: Activate NOIP service.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.5.10 MAC Address Clone Clone or change the MAC address of the WAN interface. The setup is shown in Figure 4-5-12. Figure 4-5-12: MAC Address Clone Object Description Clone WAN MAC Set the function as enable or disable. MAC Address Input a MAC Address, such as A8:F7:E0:00:06:62.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.6 Cellular The Cellular menu provides LTE/NR related functions as shown in Figure 4-6-1. Please refer to the following sections for the details. Figure 4-6-1: Cellular menu Object Description LTE/NR Configuration Allows setting LTE/NR configuration. LTE/NR Advanced Allows setting SIM configuration. LTE/NR Status Display the status of cellular. LTE/NR Statistics Display the statistics of cellular.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.6.1 LTE/NR Configuration This page provides LTE/NR configuration as shown in Figure 4-6-2. Figure 4-6-2: LTE/NR configuration Object Description Indicates what kind of LTE will be used. Possible modes are: Auto: Automatically connect the possible band. 4G&5G Only: Connect to 4G or 5G network only. LTE/NR Config 5G Only: Connect to 5G network only. 4G Only: Connect to 4G network only. 3G Only: Connect to 3G network only.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.6.2 LTE/NR Advanced This page provides LTE/NR advanced configuration as shown in Figure 4-6-3. Figure 4-6-3: LTE/NR advanced Object Current SIM Card Disable Roaming Description Display which SIM slot is using. Disable: SIM gets connection even it is in roaming state. Enable: SIM would not get connection when in roaming state. Used SIM Configure which SIM card is used or dual SIM cards.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Description Confirmed SIM PIN Confirm PIN code. APN APN can be input by user or the system.. Username The username can be input by user or the system. Password The password can be input by user or the system. Confirm Password Fill in your changed password.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.6.3 LTE/NR Status This page displays LTE/NR status as shown in Figure 4-6-4. Figure 4-6-4: LTE/NR status 4.6.4 LTE/NR Statistics This page displays LTE/NR status as shown in Figure 4-6-5.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.6.6 GPS This page displays GPS status as shown in Figure 4-6-6. Figure 4-6-6: GPS 4.6.7 SMS This page provides SMS configuration as shown in Figure 4-6-7.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.7 Security The Security menu provides Firewall, Access Filtering and other functions as shown in Figure 4-7-1. Please refer to the following sections for the details. Figure 4-7-1: Security menu Object Description Firewall Allows setting DoS (Denial of Service) protection as enable. MAC Filtering Allows setting MAC Filtering. IP Filtering Allows setting IP Filtering. Web Filtering Allows setting Web Filtering.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.7.1 Firewall A "Denial-of-Service" (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service. The cellular gateway can prevent specific DoS attacks as shown in Figure 4-7-2. Figure 4-7-2: Firewall Object Description The SPI Firewall prevents attack and improper access to network SPI Firewall resources. The default configuration is enabled. SYN Flood is a popular attack way.
Industrial 5G NR Cellular Gateway ICG-2515-NR series ICMP is kind of a pack of TCP/IP; its important function is to transfer Block ICMP Flood simple signal on the Internet. There are two normal attack ways which hackers like to use, Ping of Death and Smurf attack. The default configuration is disabled. IP TearDrop If the function is enabled, the cellular gateway will block Teardrop attack that is targeting on TCP/IP fragmentation reassembly codes.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.7.2 MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network or Internet through the cellular gateway Use of such filters can be helpful in securing or restricting your local network as shown in Figure 4-7-3. Figure 4-7-3: MAC Filtering Object Description Set the function as enable or disable.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.7.3 IP Filtering IP Filtering is used to deny LAN users from accessing the public IP address on internet as shown in Figure 4-7-4. To begin blocking access to an IP address, enable IP Filtering and enter the IP address of the web site you wish to block. Figure 4-7-4: IP Filtering Object Description IP Filtering Set the function as enable or disable. Add IP Filtering Rule Go to the Add Filtering Rule page to add a new rule.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Description Anywhere (of destination Check the box if you want to control all web sites, meaning the LAN IP Address) user can’t visit any web site. Destination Port Protocol Input the port of destination IP Address which you want to block. Leave it as blank if you want to block all ports of the web site. Select the protocol type (TCP, UDP or all). If you are unsure, please leave it to the default all protocol.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.7.5 Web Filtering Web filtering is used to deny LAN users from accessing the internet as shown in Figure 4-7-6. Block those URLs which contain keywords listed below. Figure 4-7-6: Web Filtering Object Description Web Filtering Set the function as enable or disable. Add Web Filtering Rule Go to the Add Web Filtering Rule page to add a new rule.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.7.7 Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall as shown in Figure 4-7-8. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Cellular gateway's NAT firewall.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Virtual Server IP Address Description Enter the local IP address. Enter local ports you want to control. For TCP and UDP Services, Internal Service Port enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. 4.7.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.8 Virtual Private Network To obtain a private and secure network link, the cellular gateway is capable of establishing VPN connections. When used in combination with remote client authentication, it links the business’ remote sites and users, conveniently providing the enterprise with an encrypted network communication method.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.8.1 IPSec IPSec (IP Security) is a generic standardized VPN solution. IPSec must be implemented in the IP stack which is part of the kernel. Since IPSec is a standardized protocol it is compatible to most vendors that implement IPSec. It allows users to have an encrypted network session by standard IKE (Internet Key Exchange). We strongly encourage you to use IPSec only if you need to because of interoperability purposes.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-8-3: IPSec Tunnel Object Description IPSec Tunnel Enable Check the box to enable the function. Tunnel Name Enter any words for recognition. This is only available for host-to-host connections and specifies to Interface which interface the host is connecting. 1. WAN 1. 2. WAN 2. Local Network The local subnet in CIDR notation. For instance, "192.168.1.0”.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Remote IP Address Input the IP address of the remote host. For instance, "210.66.1.10”. Remote Network The remote subnet in CIDR notation. For instance, "210.66.1.0”. Remote Netmask The netmask of the remote host. Set up the detection time of DPD (Dead Peer Detection). By default, the DPD detection’s gap is 30 seconds, over 150 seconds to think that is the broken line.
Industrial 5G NR Cellular Gateway ICG-2515-NR series by using it three times. It can achieve an algorithm up to 168 bits. 3. SHA1: The SHA1 is a revision of SHA. It has improved the shortcomings of SHA. By producing summary hash values, it can achieve an algorithm up to 160 bits. 4. SHA2: Either 256, 384 or 512 can be chosen. 5. MD5 Algorithm: MD5 processes a variably long message into a fixed-length output of 128 bits. You can specify how long ESP packets are valid.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Figure 4-8-5: GRE Tunnel Object Description Active Check the box to enable the function. Tunnel Name Enter any words for recognition. This is only available for host-to-host connections and specifies to which interface the host is connecting. Through 1. LAN. 2. WAN 1. 3. WAN 2. Peer WAN IP Address Input the IP address of the remote host. For instance, "210.66.1.10”. Peer Netmask The remote subnet in CIDR notation. For instance, "210.66.1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.8.3 PPTP Server Use the IP address and the scope option needs to match the far end of the PPTP server; its goal is to use the PPTP channel technology, and establish Site-to-Site VPN where the channel can have equally good results from different methods with IPSec. The PPTP server is shown in Figure 4-8-6. Figure 4-8-6: PPTP server Object Description PPTP Server Set the function as enable or disable. Broadcast Enter any words for recognition.
Industrial 5G NR Cellular Gateway ICG-2515-NR series DNS WINS Server IP Address When the PPTP client connects to the PPTP server, it will assign the DNS server IP address to client. When the PPTP client connects to the PPTP server, it will assign the WINS server IP address to client. Input the IP address of the PPTP Server. For instance, "192.168.10.1”. When the VPN connection is established, the VPN client will get IP Clients IP Address address from the VPN Server. Please set the range of IP Address.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.8.4 L2TP Server This section assists you in setting the L2TP Server as shown in Figure 4-8-7. Figure 4-8-7: L2TP Server Object Description L2TP Server Set the function as enable or disable. Server IP Address Input the IP address of the L2TP Server. For instance, "192.168.50.1”. When the VPN connection is established, the VPN client will get IP Clients IP Address address from the VPN Server. Please set the range of IP Address.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Description Preshare Key Enter a pass phrase. User and Password Create the username and password for the VPN client. Connection Type 1. Main. 2. Aggressive. It provides the way to create the SA between two PCs. The SA can access the encoding between two PCs, and the IT administrator can assign to which key size or Preshare Key and algorithm to use. The SA comes in many connection ways. 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.8.6 SSL VPN This section assists you in setting the SSL Server as shown in Figure 4-8-8. Figure 4-8-8: SSL Server Object Description SSL VPN Server Set the function as enable or disable. Port Set a port for the SSL Service. Default port is 1194. Tunnel Protocol Set the protocol as TCP or UDP. Virtual Network Device Set the Virtual Network Device as TUN or TAP. Interface User is able to select the interface for SSL service using.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.8.8 VPN Connection This page shows the VPN connection status as shown in Figure 4-8-9. Figure 4-8-9: VPN Connection Status Object Description VPN Connection Click the IPSec/GRE/…/SSL VPN bookmark to check the current Status connection status.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9 AP Control The AP Control menu provides the following features for managing the system as Figure 4-9-1 is shown below: Figure 4-9-1: AP Control Menu Object Preference Description Edit region, RO community, RW community AP Search Search APs in the same domain AP Management Config APs IP Address, Subnet Mask, SSID and Radio Profiles AP Group Management Grouping same model AP SSID Profile Setup SSID Profile Radio 2.4G Profile Setup Radio 2.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.1 Preference On this page, you can choose the device region of FCC or ETSI. Then edit RO community and RW community for public or private use. Select Apply or Reset. This screenshot is as shown in Figure 4-9-2. Figure 4-9-2: AP Control Menu Noted: Device of FCC and device of ETIS cannot be shown at the same time. 4.9.2 AP Search On this page, you can add new APs in your AP Control System. Step as follows : Step 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.4 AP Management On this page, you can management your APs, Including check AP online status, config AP (IP address, Mask, SSID and Radio profile), reboot AP, firmware update, delete AP in the AP Control system. Status Object Description Connection status: online, offline, Wi-Fi disabled In progress: action in progress Finished/Successful: action finished and successful. Failed: action failed.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.5 AP Group Management On the AP Group Management page, you can create AP group and control one or more AP groups. Action: Object Description Add new group: Click it to add an AP group Delete selected item: Click it to delete the selected AP group Create Group: 1. Select AP Model No. you want to Add 2. Type AP Group Name and AP Group Description. 3. Select AP you want to add in group member setting area and press Add button. 4.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.6 SSID Profile On the SSID profile configuration page, enter the value that you preferred and then click “Apply” to save the profile Action: Object Description Add new profile: Click it to add a new profile. Delete selected item: Click it to delete the selected profile. Edit: Click it to edit the profile. Delete: Click it to delete the single profile.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.8 Radio 2.4G Profile On the Radio profile configuration page, enter the value that you preferred and then click “Apply” to save the profile. Action: Object Description Add new profile: Click it to add a new profile. Delete selected item: Click it to delete the selected profile. Edit: Click it to edit the profile. Delete: Click it to delete the single profile. Notes: 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.10 Radio 5G Profile On the Radio profile configuration page, enter the value that you preferred and then click “Apply” to save the profile. Action: Object Description Add new profile: Click it to add a new profile. Delete selected item: Click it to delete the selected profile. Edit: Click it to edit the profile. Delete: Click it to delete the single profile. Notes: 1.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.11 Statistics AP Status On this page, you can observe the current configuration of all managed APs. Filter: You can filter the AP list by entering the keyword in the field next to the magnifier icon. The keyword should be in any context that belongs to the fields of this page. 4.9.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.14 Map It On this page you can add managed APs to the actual position against the floor map. This is convenient to user to view and adjust the actual deployment by reference to its real transmission power and channel allocation. 1. Click “Scale” to start to reset the map scale. 2. Press the set button to draw a line on the map. Fill its physical distance in the blank and press Set or Cancel. For example, in the graph below, set the door width to 0.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.9.16 Upload Map On this page, the system allows you to upload your floor map to the system. Note: The system allows user to upload up to 10 floor maps.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10 Wireless The Wireless menu provides the following features as shown in Figure 4-10-1 Figure 4-9-1: Wireless Menu Object Description 2.4G WiFi Allow to configure 2.4G WiFi. 5G WiFi Allow to configure 5G WiFi. MAC ACL Allow configure MAC ACL. WiFi Advanced Allow to configure advanced setting of WiFi. WiFi Statistics Display the statistics of WiFi traffic. Connection Status Display the connection status.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10.1 2.4G WiFi This page allows the user to define 2.4G WiFi as shown in Figure 4-10-2. Figure 4-10-2: 2.4G WFI Object Description Wireless Status Allows user to enable or disable 2.4G WiFi Wireless Name (SSID) It is the wireless network name. The default 2.4G SSID is “PLANET_2.4G” Hide SSID Allows user to enable or disable SSID Bandwidth Select the operating channel width, “20MHz” or “40MHz” Channel It shows the channel of the CPE.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10.2 5G WiFi This page allows the user to define 5G WiFi as shown in Figure 4-10-3. Figure 4-10-3: 5G WFI Object Description Wireless Status Allows user to enable or disable 5G WiFi Wireless Name (SSID) It is the wireless network name. The default 5G SSID is “PLANET_5G” Hide SSID Allows user to enable or disable SSID Bandwidth Select the operating channel width, “20MHz” or “40MHz” or “80MHz” Channel It shows the channel of the CPE.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10.3 MAC ACL This page provides MAC ACL configuration as shown in Figure 4-10-4.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10.4 WiFi Advanced This page allows the user to define advanced setting of WiF as shown in Figure 4-10-5. Figure 4-10-5: WiFi advanced Object 2.4G Mode Description 11AC: Select 802.11B/G or 802.11N/G 11AX: Select 802.11B/G or 802.11N/G or 802.11AX 5G Mode 11AC: Select 802.11A or 802.11AN or 802.11AC 11AX: Select 802.11A or 802.11AN or 802.11AC or 802.11AX 2.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10.5 WiFi Statistics This page displays WiFi statistics as shown in Figure 4-10-6.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.10.6 Connection Status This page shows the host names and MAC address of all the clients in your network as shown in Figure 4-10-7. Figure 4-10-7: Connection status Object Description Name Display the host name of connected clients. MAC Address Display the MAC address of connected clients. Signal Display the connected signal of connected clients. Connected Time Display the connected time of connected clients.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.11 Maintenance The Maintenance menu provides the following features for managing the system as shown in Figure 4-11-1 Figure 4-11-1: Maintenance Menu Object Description Administrator Allows changing the login username and password. Date & Time Allows setting Date & Time function. Save/Restore Configuration Export the cellular gateway’s configuration to local or USB sticker.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.11.1 Administrator To ensure the cellular gateway's security is secure, you will be asked for your password when you access the cellular gateway's Web-based utility. The default user name and password are "admin". This page will allow you to modify the user name and passwords as shown in Figure 4-11-2. Figure 4-11-2: account and password page Object Description Username Input a new username. Password Input a new password.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.11.2 Date and Time This section assists you in setting the system time of the cellular gateway. You are able to either select to set the time and date manually or automatically obtain the GMT time from Internet as shown in Figure 4-11-3. Figure 4-11-3: date and time page Object Current Time Time Zone Select NTP Client Update NTP Server Description Show the current time. User is able to set time and date manually.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.11.3 Saving/Restoring Configuration This page shows the status of the configuration. You may save the setting file to either USB storage or PC and load the setting file from USB storage or PC as Figure 4-11-4 is shown below: Figure 4-11-4: Saving/Restoring Configuration ■ Save Setting to PC Object Description Configuration Export Press the button to save setting file to PC.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Object Description the 4.11.4 button first. Upgrading Firmware This page provides the firmware upgrade function as shown in Figure 4-11-5 Figure 4-11-5: firmware upgrade page Object Description Choose File Press the button to select the firmware. Upgrade Press the button to upgrade firmware to system.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.11.5 Reboot / Reset This page enables the device to be rebooted from a remote location. Once the Reboot button is pressed, users have to re-log in the Web interface as Figure 4-11-6 is shown below: Figure 4-11-6: reboot/reset page Object Description Reboot Press the button to reboot system. Reset Press the button to restore all settings to factory default settings. I'd like to keep the network profiles.
Industrial 5G NR Cellular Gateway ICG-2515-NR series 4.11.6 Diagnostics The page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues. After you press “Ping”, ICMP packets are transmitted, and the sequence number and roundtrip time are displayed upon reception of a reply.
Industrial 5G NR Cellular Gateway ICG-2515-NR series Appendix A: DDNS Application Configuring PLANET DDNS steps: Step 1: Visit DDNS provider’s web site and register an account if you do not have one yet. For example, register an account at http://planetddns.com Step 2: Enable DDNS option through accessing web page of the device. Step 3: Input all DDNS settings.