720p SIP Multi-unit Apartment Vandalproof Door Phone with RFID and PoE HDP-5260PT Quick Installation Guide
Table of Contents 1. Package Contents........................................................................................ 3 2. Physical Specifications.................................................................................. 4 3. Installation.................................................................................................. 9 4. Searching Door Phone.................................................................................14 5. SIP Door Phone Setting........................
1. Package Contents Thank you for choosing PLANET HDP-5260PT. Before installing the door phone, please verify the contents inside the package box.
2. Physical Specifications Dimensions (W x D x H) 223 x 74 x 130 mm Weight 1850g (gross weight) 2.1 Front Panel Wall-mount Housing CMOS Sensor Speaker Numeric Keyboard Lock Call Ring Network & SIP Registration RFID Reader DSS Key Mics Interface Description Wall-mount Housing IP65 and IK10 outdoor housing for rigorous environment. CMOS Sensor The door phone has a built-in IP camera supporting a high-resolution video of up to 1280 x 720 pixels.
Speaker The door phone has a built-in speaker for convenient communication and alert use. Mics The door phone has a built-in microphone hidden in the pinhole located on the front panel. RFID Reader Use RFID cards to unlock the door by touching RFID reader of device. Button Definition Button Description DSS Key Press the Direct Station Selection key to check who the caller is before opening the doors, or talking to him/her. Numeric Keyboard Input password to open the door or call.
2.2 I/O Control Description After removing the front panel of HDP-5260PT, there are two terminal block connectors for power connection and digital I/O connections as shown in the picture below. JP1 Jumper Power Connector Electric-lock Connector Power Connector The HDP-5260PT requires either IEEE 802.3af/at PoE or DC power from the power connector. It shows the two-pin connector comes with a power source of 12V DC, 1A (max.).
Electric-lock Connector 1 2 3 4 5 1 2 3 4 5 S_IN S_OUT NC COM NO Indoor switch Electric-lock switch JP1 Jumper There are two modes for power supply of electric-lock as shown in the picture below. Active Mode: When the electric-lock starting current is less than 12V/700mA, please adjust the jumper to 1/2/3/4 pin (Default mode). Passive Mode: When the electric-lock starting current is more than 12V/700mA, please adjust the jumper to 2/3 pin.
Wiring instructions NO: Normally Open Contact COM: Common Contact NC: Normally Close Contact Driving Mode Active Passive √ Driving Mode NO √ √ √ √ √ √ √ 8 NC √ √ Jumper Port Connections
3. Installation The HDP-5260PT is constructed of four parts as shown below. Prior to the installation, the installer is required to remove the front panel of the HDP-5260PT for wall mounting. Please follow the steps below for the installation. Front Panel Main Part of Intercom Rain Shade Back Panel Figure 1 Four Major Parts of HDP-5260PT Step 1: Installation preparation A.
0-120 cm 100-150 cm Step 2: Drilling Figure 2 Wall Mounting A. Place the mounting template with dimensions on the surface of a wall in a desired flat position. B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 50mm deep. Remove the template when finishing drilling. C. Push or hammer screw anchors into the drilled holes. While drilling or fixing the HDP-5260PT, hold it tight or else it may drop that may accidentally hurt the installer.
Step 3: Removing Front Panel A. With hex wrench, remove the front panel as shown in Figure 3. (Turn counterclockwise) and Figure 4.Step 3: Removing Front Panel Figure 3 Figure 4 B. With Phillips screwdriver, unpack the rain shade and the main part of intercom as shown in Figure 5.
Step 4: Back Panel Fixing and Cabling 15cm TA5 x 40mm Figure 6 Figure 7 A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended. B. With 4 TA5 x 40mm screws, tighten the back panel on the wall as shown in Figure 6. Note The direction of the cable hole on the back panel should be pointing down. C. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connectors description (refer to Section 2). D.
Step 5: Mounting M4 x 16mm MP3 x 16mm Figure 8 Figure 9 A. Use the 6 screws to tighten the main part (together with the rain shade) of intercom on the back panel as shown in Figure 8. B. Push the front panel into the plastic frame and tighten it with 6 screws as shown in Figure 9. Note Make sure the screws have been tightened properly for better waterproof effect.
4. Searching Door Phone There are two methods as shown below to search the HDP-5260P. Method 1: Open the Planet Door Phone Finder Utility. Press the Refresh button to search the HDP-5260PT and find the IP address. Method 2: Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice. 1 2 3 7 8 9 4 5 0 6 # Default Setting Default DHCP Client On Default IP Address 172.16.0.
5. SIP Door Phone Setting Please refer to the following steps to set the SIP door phone. Step 1: Login the homepage of the HDP-5260PT. Step 2: Add the SIP account. Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters. Select “enable registration”, and then click Apply to save this setting.
Step 3: Setting DSS key Set the DSS key as shown below for a quick start. Click “Apply” to save this setting. Type: Hot Key Number 1: The DSS Key will dial to this Number 1. Number 2: If Number 1 is unavailable, it will be forwarded to Number 2.
6. Door Unlocking Setting Local Local Password Step 1: Go to Door Phone Set Local Password (The default is “6789”). Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked. Private Access Code Step 1: Go to Door Access Enable local authentication. Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.
Remote Remote Password Step 1: Go to Door Phone Set Remote Password (The default is “*”). Step 2: To answer the call made by visitor via SIP phone, press the “*” key to unlock the door for visitor. RFID Card Step 1: Go to Door Card Enter the ID of RFID card (Only Front 10 yards) Press Add to Door Card Table. Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET Home Automation support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq.php?key=HDP-5260PT Door Phone support team mail address: support@planet.com.tw HDP-5260PT Utility: http://www.planet.com.tw/en/support/download.
