720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Copyright Copyright 2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Table of Contents Chapter 1. Product introduction .................................................................................... 11 1.1 1.2 1.3 1.4 Package Contents ......................................................................................... 11 Overview ........................................................................................................ 12 Features ......................................................
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 6. Other instructions ......................................................................................... 75 6.1 Open door modes ......................................................................................... 75 6.2 Management of Card .................................................................................... 76 6.2.1 Administrator Table ........................................................................
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 1. Product introduction 1.1 Package Contents Please read the following safety notices before installing or using this unit. They are crucial for the safe and reliable operation of the device. The package should contain the following items: SIP Door Phone Unit x 1 Quick Installation Guide x 1 Screw Kit x 1 Wrench x 1 RFID Card x 3 If any of the above items are missing, please contact your dealer immediately.
20p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 1.2 Overview Security is Ensured with PLANET Video Door Phone PLANET HDP-5240PT is a SIP Door Phone with PoE feature. It supports H.264 video compression format and delivers excellent picture quality in 720p HD video resolutions at 10~30 frames per second (fps). It also supports HD (High Definition) voice and G.722 codec that relax bandwidth limitation and provide clear communications.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Keyless Control and Convenience PLANET HDP-5240PT advancements in residential door lock security have been enhanced with secure authentication technology which supports many ways of opening door without a key. The door not only can be open via an RFID card but also a password if it is an electronic door lock. Thus, you can enter your home without having to use a key. SIP 2.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT AEC (Acoustic Echo Cancellation) Acoustic Echo Cancellation (AEC) technology is adopted in PLANET’s HDP-5240PT Door Phone and HTS-1000P Touch Screen Control Pad to enable users to minimize the voice/sound signal distortion shown in the diagram below, thus guaranteeing the best-in-class sound quality.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 15
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 1.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 1.4 Specifications Product HDP-5240PT Video Image Device 1/4" color CMOS, Pixels: 1 million Video Codec H.264 Resolution Main stream 1280 x 720 Sub-stream 640 x 360, 352 x 288, 32 x 240 Viewing Angle 110° (H), 95° (V) Minimum Illumination 1 lux Audio Audio Streaming Two-way audio Narrowband Codec G.711a/u, G.723.1, G.726-32K, G.729AB Broadband Speech Codec G.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Network and Protocols IEEE 802.3 10BASE-T Network Standard IEEE 802.3u 100BASE-TX IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus QoS 802.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Net Weight 0.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 2. Hardware Interface and Installation 2.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 2.2 Description Interface Camera Mic Speaker RFID Reader Description The door phone has a built-in IP camera supporting a high-resolution video of up to 1280 x 720 pixels. The door phone has a built-in microphone hidden in the pinhole located on the front panel. The door phone has a built-in speaker for convenient communication and alert use. Use RFID cards to unlock the door by touching RFID reader of device.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 3. Start Using Before you start to use the equipment, please make the following installation. 3.1 Confirm the Connection Confirm whether the equipment of the power cord, network cable, electric lock control line connection and the boot-up is normal. (Check the network state of light) 3.1.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Power Connector The HDP-5240PT requires either IEEE 802.3af/at PoE or DC power from the power connector. It shows the two-pin connector comes with a power source of 12V DC, 1A (max.). Network Connector Power and Electric-lock Connector CN7 1 2 3 4 5 6 7 +12V VSS NC COM NO S_IN S_OUT 12V DC, 1A Electric-lock switch Indoor switch 3.1.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 3.1.4 Wiring Instructions NO: Normally Open Contact. COM: Common Contact. NC: Normally Close Contact.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 3.2 Installation The HDP-5240PT is constructed of four parts as shown below. Prior to the installation, the installer is required to remove the front panel of the HDP-5240PT for wall mounting. Please follow the steps below for the installation. Figure 1 Three Major Parts of HDP-5240PT Step 1: Installation Preparation A.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Step 2: Drilling Figure 2 Wall Mounting A. Place the mounting template with dimensions on the surface of a wall in a desired flat position. B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 30mm deep. Remove the template when finishing drilling. C. Push or hammer screw anchors into the drilled holes. Step 3: Removing Hanging Panel A.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT B. With Phillips screwdriver, unpack the Back Panel and the main part of intercom as shown in Figure 5. Figure 5 Step 4: Hanging Shell Fixing and Cabling Figure 6 A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended. B. With 4 KA4 x 25mm screws, tighten the wall-mounted hanging shell as shown in Figure 6.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Step 5: Connection Line Figure 7 Figure 8 A. Select the hole for cable supply. B. Connect the cables of RJ45, power, and electric lock to the motherboard socket as mentioned in connectors description (refer to Section 2). C. Test whether there is electricity by doing the following: (A) Press the # button for 3 seconds to get the IP address of intercom by voice.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT A. Use the 4 screws to tighten the main part of intercom on the back panel as shown in Figure 9. B. Push the device into the wall-mounted hanging shell and tighten it with 1 screw as shown in Figure 10. C. Make sure the screws have been tightened properly for better waterproof effect.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 3.3 Quick Setting The product provides a complete function and parameter setting. Users may need to have the network and SIP protocol knowledge to understand the meaning all parameters represent.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 4. Basic Operation 4.1 Answer a Call When a call comes in, the device would answer automatically. If you cancel auto answer feature and set auto answer time, you would hear the ring at the set time and the device would auto answer after configuring the timer. 4.2 Call Configure the shortcut key as hot key and then set up a number; after that you might press the shortcut key for making a call to the configured extension(s). 4.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT If access code has been input correctly, the device would play siren sound to prompt the HDP-5240PT and the remote user, while input error by low-frequency short chirp. Password input successfully followed by high-frequency siren sound, while input falsely, there would be high-frequency short chirp. When the door has been opened, the device would play siren sound to prompt guests.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 5. Page Settings 5.1 Browser Configuration When the device and your computer are successfully connected to the network, you might enter the IP address of the device in the browser as http://172.16.0.1/ and you can see the login interface of the web page management. Enter the user name and password and click the Logon button to enter the settings screen. 5.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Default Setting Default Web Port 80 Default Login User Name admin Default Login Password 123 Report IP Address Hold # key for 3 seconds to report IP address by voice Searching Tools Planet Door Phone Finder 5.3 Configuration via Web 5.3.1 System A. Information Information Field Name System Information Explanation Display equipment model, hardware version, software version, uptime, last uptime and meminfo.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Information Field Name Network SIP Accounts Explanation Shows the configuration information of WAN port, including connection mode of WAN port (Static, DHCP, PPPoE), MAC address, IP address of WAN port. Shows the phone numbers and registration status of the 2 SIP lines. B. Account Through this page, administrator can add or remove user accounts depending on their needs, or modify the existing user accounts by permission.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT C. Configurations Configurations Field Name Export Configurations Import Configurations Reset to factory defaults Explanation Save the equipment configuration to a txt or xml file. Please right-click on the choice and then choose “Save Link As.” Find the config file, and press Update to load it to the equipment. The HDP-5240PT would restore to factory default configuration and remove all configuration information.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT D. Upgrade Upgrade Field Name Explanation Software upgrade Find the firmware, and press Update to load it to the equipment.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT E. Auto Provision Auto Provision Field Name Explanation Common Settings Show the current config file’s version. If the config file to be downloaded is higher than the current version, the configuration would be upgraded.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Auto Provision Field Name General Configuration File Encryption Key Explanation Encryption key for common configuration file Save Auto Provision Save the auto provision username and password in the phone until the Information server URL is changed DHCP Option Option Value Custom Option Value The equipment supports configuration from Option 43, Option 66, or a Custom DHCP option. It may also be disabled. Custom option number.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Auto Provision Field Name Explanation INFORM Sending Period Time between transmissions of “Inform”; the unit is second. F. Tools Syslog is a protocol used to record log messages using a client/server mechanism. The Syslog server receives the messages from clients, and classifies them based on priority and type. Then these messages would be written into a log by rules which the administrator has configured.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Tools Field Name Explanation Syslog Enable Syslog Enable or disable system log. Server Address System log server IP address. Server Port System log server port. App Log Level Set the level of App log. SIP Log Level Set the level of SIP log. Network Packets Capture Capture a packet stream from the equipment. This is normally used to troubleshoot problems.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 5.3.2 Network A. Basic Field Name Explanation Network Status IP The current IP address of the equipment Subnet mask The current Subnet Mask Default gateway The current Gateway IP address MAC The MAC address of the equipment MAC Timestamp Get the MAC address’ time. Settings Select the appropriate network mode. The equipment supports three network modes: Static IP Network parameters must be entered manually and would not change.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Field Name Explanation If Static IP is chosen, the screen below would appear. Enter values provided by the ISP. DNS Server Configured by Primary DNS Server Secondary DNS Server Select the Configured mode of the DNS Server. Enter the server address of the Primary DNS. Enter the server address of the Secondary DNS. After entering the new settings, click the Apply button. The equipment would save the new settings and apply them.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT In practice, VLANs are distinguished by the use of VLAN IDs.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Advanced Field Name Explanation Link Layer Discovery Protocol (LLDP) Settings Enable LLDP Enable or Disable Link Layer Discovery Protocol (LLDP) Enables the telephone to synchronize its VLAN data with the Network Switch. Enable Learning Function The telephone would automatically synchronize DSCP, 802.1p, and VLAN ID values even if these values differ from those provided by the LLDP server.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 802.1X Settings Enable 802.1X Enable or Disable 812.1X Username 802.1X user account Password 802.1X password HTTPS Certification File Upload or delete HTTPS Certification File C. VPN The device supports remote connection via VPN. It supports both Layer 2 Tunneling Protocol (L2TP) and OpenVPN protocol. This allows users at remote locations on the public network to make secure connections to local networks.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Field Name Explanation VPN IP Address Shows the current VPN IP address. VPN Mode Enable VPN Enable/Disable VPN. L2TP Select Layer 2 Tunneling Protocol Select OpenVPN Protocol. (Only one protocol may be activated. After OpenVPN the selection is made, the configuration should be saved and the phone be rebooted.) Layer 2 Tunneling Protocol (L2TP) L2TP Server Address Set VPN L2TP Server IP address.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 5.3.3 Line A. SIP You can configure a SIP server on this page. SIP Field Name Explanation Basic Settings (Choose the SIP line to configure) Line Status Display the current line status after page loading. To get the up-to-date line status, user has to refresh the page manually. User Name Enter the username of the service account. Display Name Enter the display name to be sent in a call request.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT SIP Field Name Explanation Codecs Settings Set the priority and availability of the codecs by adding or removing them from the list.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT SIP Field Name Explanation Advanced Settings Call Forward Unconditional Call Forward Number for Unconditional Call Forward on Busy Call Forward Number for Busy Call Forward on No Answer Enable unconditional call forwarding; all incoming calls would be forwarded to the number specified in the next field Set the number of unconditional call forwarding Enable call forward on busy, when the phone is busy, any incoming call would be forwarded
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT SIP Field Name Explanation specified in the next field Call Forward Number for No Answer Call Forward Delay for No Answer Hotline Delay Enable Auto Answering Auto Answering Delay Subscribe For Voice Message Voice Message Number Voice Message Subscribe Period Set the number of call forward on no answer Set the delay time of not answered call before being forwarded Set the delay for hotline before the system automatically dial it Enable
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT SIP Field Name Explanation Server Conference Number Set the conference room number when conference type is set be Server Transfer Timeout Set the timeout of call transfer process Enable Long Contact Allow more parameters in contact field per RFC 3840 Enable Missed Call Log Response Single Codec If it is enabled, the phone would save missed calls into the call history record.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT SIP Field Name Explanation Enable Rport Set the line to add Rport in SIP headers Enable PRACK Set the line to support PRACK SIP message Keep Authentication Keep the authentication parameters of previous authentication Auto TCP Using TCP protocol to guarantee usability of transport when SIP messages have more than 1500 bytes Enable Feature Sync Feature Sync with server Enable GRUU Support Globally Routable User-Agent URI (GRUU) T
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Basic Settings Field Name Explanation SIP Settings Local SIP Port Registration Failure Retry Interval Set the local SIP port used to send/receive SIP messages. Set the retry interval of SIP registration when registration failed. STUN Settings Server Address STUN Server IP address Server Port STUN Server Port – Default is 3478.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT The SIP STUN is used to achieve the penetration of SIP NAT; it is a realization of service. When the equipment configures the STUN server IP and port (usually the default is 3478), and selects “Use Stun SIP server”, you can make common SIP equipment achieve penetration. 5.3.4 RFID Setting A.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Features Field Name Explanation Dial Fixed Length to Send Enable or disable dial fixed length. Send Length The number would be sent to the server after the specified digits are dialed. Enable Speed Dial Hangup Use Function Key to Enable Speed Dial Hand Up function Configure whether to enable the function keys, the feature is disabled by Answer default.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Features Field Name Explanation Only password: password input only, dialing would be forbidden. Only dialing: dial input only, you can press * key to enter the dial, the # key for hanging up. Initial mode is password and dialing. Switch-On Duration Door unlocking time for Monostable mode only. If the time is up, the door would be locked automatically. Initial time is 5 seconds.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Features Field Name Explanation Door Unlock Indication Indication tone for door unlocked. There are 3 types of tone: silent, short beeps and long beeps. Remote Code Check The remote access code length would be restricted with it. If the input access code Length length is matched with it, system would check it immediately. Initial length is 4.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT B. Audio This page configures audio parameters such as voice codec, speakerphone volume, mic volume and ringer volume. Audio Setting Field Name Explanation First Codec The first codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB Second Codec The second codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, None Third Codec The third codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT C. Video This page allows you to set the video encoding and video capture, and other information. Video Encode Field Name Explanation Encode Only H.264 encoding format is supported Resolution Main stream: support 720p Sub-stream: you can select 360P, CIF (352 x 288), QVGA (240 x 320) CBR: If the code rate (bandwidth) is insufficient, it is preferred. Bitrate Control VBR: Image quality is preferred, not recommended.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Video Encode Field Name Explanation Activate When you select it, the main stream is enabled; otherwise, disabled Video Capture Brightness Adjust the video brightness level Adjust the video color purity; the higher the value is, the more vivid colors might be Saturation displayed Sharpness Adjust video clarity Contrast Adjust the video brightness ratio Backlight Control Video background brightness Video Format Based on the powe
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT D. MCAST It is easy and convenient to use multicast function to send notice to each member of the multicast via setting the multicast key on the device and sending multicast RTP stream to pre-configured multicast address. By configuring monitoring multicast address on the device, the device monitors and plays the RTP stream which is sent by the multicast address.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT multicast session currently. When page priority switch is enabled, the device would automatically ignore the low priority multicast RTP streams but receive top-level priority multicast RTP streams, and keep the current multicast session in the current status. If it is not enabled, the device would automatically ignore all receiving multicast RTP streams. c.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT b. Purple part (host: port) It is a set of addresses and ports to listen, separated by a colon. c. Pink part (index / priority) Multicast is a sign of listening, but also the monitoring multicast priority. The smaller number refers to higher priority. d. Red part (priority) It is the general call, non-multicast call priority. The smaller number refers to higher priority.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT b. Monitor: IP port and priority are configured to monitor the device, when the call is initiated by multicast and the call is successful, the device would directly enter the Talking interface. E. Action URL Action URL Field Name Explanation Action URL Event Settings URL for various actions performed by the phone. These actions are recorded and sent as xml files to the server. Sample format is http://InternalServer /FileName.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT F. Time/Date Time/Date Field Name Explanation Network Time Server Settings Time Synchronized via SNTP Time Synchronized via DHCP Primary Time Server Enable time-sync through SNTP protocol Enable time-sync through DHCP protocol Set primary time server address Set secondary time server address.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Time/Date Field Name Explanation Date Format 12-hour Clock Set the time display in 12-hour mode Date Format Select the time/date display format Daylight Saving Time Settings Location DST Set Type Select the user's time zone according to specific area Select automatic DST according to the preset rules of DST, or you can manually input rules Offset The DST offset time Month Start The DST start month Week Start The DST start week
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT RFID Cards Field Name Explanation Import Door Card Table Click to choose importing door card list file (doorCard.csv); click to batch import. Door Card Table Add Door Card You should input the top 10 digits of RFID card numbers, for example, 0004111806, by clicking . Click Here to Save Right-click it and select saving target to your Door Card Table computer. Name The name of users who own issued cards.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT B. RFID Access Field Name Explanation Import Access Table Click the to choose to import remote access list file (access List.csv) and then clicking can batch import remote access rule. Access Table According to entrance guard access rules that have been added, you can choose single or multiple rules on this list to delete operation.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Field Name Explanation 2. The user’s private password should be input via keypad for local door unlocking. Access Code Action Double Auth Type Profile Location Select Access Code Action mode When the feature is enabled, private password inputting and RFID reading must be matched simultaneously for door unlocking. Host: The door phone would answer all calls automatically.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 5.3.6 Call Logs According to open event log, the device can record up to 150 thousands of open events; it would cover the old Right-click on the links to select records after the records exceed 150 thousands. saving target as the door log can export CSV format. Field Name Explanation Door Open Log Result Show the results of the open the door ( Succeeded or Failed) Time The time of opening door. Duration Duration of opening the door.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 5.3.7 Function Key A. Function Key Settings (A) Key Event You might set up the key type with the Key Event. Type Key Event Subtype Usage None Not responding Dial Dialing function Release Delete password input, cancel dialing input and end call OK identification key Handsfree The hands-free key(with hooking dial, hanging up functions) (B) Hot Key You might enter the phone number in the input box.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Type Number Line Subtype Usage Using Fill out the called Hot Key party’s SIP account or IP address The SIP Speed Dial account Speed Dial mode together , can with define whether this call is allowed to be hung up by re-pressing the speed dial key.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT configure via WEB to monitor the multicast address and port. When the device makes a multicast, all devices monitoring the address can receive the multicast data. b. Calling configuration If the device is on calls, or it is three-way conference, or initiated multicast communication, the device would not be able to launch a new multicast call.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Chapter 6. Other instructions 6.1 Open door modes A. Local control (A) Local Password a. Set (the password is "6789" by default) via Phone Setting\Feature\Advanced Settings. b. Input password via keypad and press the "#" key, then the door would be unlocked. (B) Private access code a. Set and enable local authentication. b.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT 6.2 Management of Card 6.2.1 Administrator Table A. and (A) Add Administrator cards Input a card’s ID, selected or in the field and then click ; you would add administrator card. (B) Delete Administrator cards To delete the selected admin card, click . 6.2.2 Add user cards A.
0p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT tone from the device. Repeat step to add more cards. (D) On the web page < Phone Setting →Features →Card Reader Working Mode > option, select . (E) Click and Card Reader would return to the Normal status. (F) The issuing records can be found from the door card table list. B.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Only need to input the first 10 numbers. 6.2.3 Delete user cards A. Method 1: It is used to batch delete cards for starters. (A) On the web page < Phone Setting →Features →Card Reader Working Mode > option, select . (B) Click and card reader would enter the revoking status. (C) Use card to touch card reader induction area, and you might hear the card reader confirmed indication tone. Repeat step to delete more cards.
720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT C. Method 3: bulk delete or partially delete card records (A) On the web page select the card ID and then click . If you click , system would delete all the ID card records.
