720p SIP Multi-unit Video Door Phone with RFID and PoE HDP-5240PT Quick Installation Guide
Table of Contents 1. Package Contents.............................................................................3 2. Physical Specifications.......................................................................4 2.1 Front Panel................................................................................4 2.2 I/O Control Description...............................................................6 3. Installation.....................................................................................10 4.
1. Package Contents Thank you for choosing PLANET HDP-5240PT. Before installing the door phone, please verify the contents inside the package box.
2. Physical Specifications Dimensions (W x D x H) 160 x 93 x 35 mm Weight 330g (gross weight) 2.1 Front Panel MIC RFID Reader Camera Lock Status Call and Ring Status Network and Registration Status Numeric Keypad (password or dialing) Speaker Interface DSS Key with LED Description Camera The door phone has a built-in IP camera supporting a high-resolution video of up to 1280 x 720 pixels. Mic The door phone has a built-in microphone hidden in the pinhole located on the front panel.
Button Definition Button Description Programmable Keys It can be set with a variety of functions in order to meet the needs of different occasions Numeric Keyboard Input password to open the door or calls.
2.2 I/O Control Description After removing the front panel of HDP-5240PT, there are two terminal block connectors for power connection and digital I/O connections as shown in the picture below. Network port Power and lock connector JP1 Jumper Power Connector The HDP-5240PT requires either IEEE 802.3af/at PoE or DC power from the power connector. It shows the two-pin connector comes with a power source of 12V DC, 1A (max.).
Power and Electric-lock Connector 1 2 3 4 5 6 7 +DC 12V VSS NC COM NO S-IN S-OUT 12V DC Input Electric-lock switch Indoor switch JP1 Jumper There are two modes for power supply of electric-lock as shown in the picture below. (The default is “Active Mode”). Passive Mode: When the electric-lock starting current is more than 12V/1000mA, the external drive mode, the electric lock interface for short circuit output control, is used.
Driving Mode Active Passive √ Electric-lock Mode No electricity when open √ √ √ √ √ Connections Graphs Please refer to the Graph 2 in the next page Please refer to the Graph 3 in the next page √ √ JP1 Jumper Active Please refer to the Graph 1 in the next page √ √ 8 Electrify when open Please refer to the Graph 4 in the next page Please refer to the Graph 5 in the next page
Graph 1 Graph 2 Graph 3 Graph 4 Graph 5 9
3. Installation The HDP-5240PT is constructed of four parts as shown below. Prior to the installation, the installer is required to remove the front panel of the HDP-5240PT for wall mounting. Please follow the steps below for the installation. Figure 1 Three Major Parts of HDP-5240PT Step 1: Installation preparation A. Check the following contents: Hex wrench x 1 RJ45 plugs x 2 (1 spare) KA4 x 25mm screws x 4 25mm screw anchors x 4 B.
Step 2: Drilling Figure 2 Wall Mounting A. Place the mounting template with dimensions on the surface of a wall in a desired flat position. B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 30mm deep. Remove the template when finishing drilling. C. Push or hammer screw anchors into the drilled holes. Step 3: Removing Hanging Panel A. Remove the hanging shell in Figure 3 and Figure 4.
B. With Phillips screwdriver, unpack the Back Panel and the main part of intercom as shown in Figure 5. Figure 5 Step 4: Hanging Shell Fixing and Cabling Figure 6 A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended. B. With 4 KA4 x 25mm screws, tighten the wall-mounted hanging shell as shown in Figure 6.
Step 5: Connection Line Figure 7 Figure 8 A. Select the hole for cable supply. B. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connectors description (refer to Section 2). C. Test whether there is electricity by doing the following: 1. Press the # button for 3 seconds to get the IP address of intercom by voice. 2. Input access password or press the indoor switch to check electriclock installation.
Step 6: Mounting Figure 9 Figure 10 A. Use the 4 screws to tighten the main part of intercom on the back panel as shown in Figure 9. B. Push the device into the wall-mounted hanging shell and tighten it with 1 screw as shown in Figure 10. C. Make sure the screws have been tightened properly for better waterproof effect.
4. Searching Door Phone IP Address There are two methods as shown below to search the HDP-5240P. Method 1: Open the Planet Door Phone Finder Utility. Press the Refresh button to search the HDP-5240PT and find the IP address. Method 2: Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice. Default Setting Default DHCP Client Off Default IP Address 172.16.0.
5. SIP Door Phone Setting Please refer to the following steps to set the SIP door phone. Step 1: Login the homepage of the HDP-5240PT. Step 2: Add the SIP account. Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters. Select “Activate”, and then click Apply to save this setting. Step 3: Setting Function (DSS) key Set the DSS key as shown below for a quick start. Click “Apply” to save this setting.
Type: Hot Key Number 1: The DSS Key will dial to this Number 1. Number 2: If Number 1 is unavailable, it will be forwarded to Number 2.
6. Door Unlocking Setting Local Local Password Step 1: Go to Features Advanced Settings Set Local Password (The default is “6789”). Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.
Private Access Code Step 1: Go to RFID Cards Access Code Action select Remote call and Local Auth. Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.
Remote Remote Password Step 1: Go to Features Advanced Settings Password (The default is “*”). Set Remote Step 2: To answer the call made by visitor via SIP phone, press the “*” key to unlock the door the visitor.
RFID Card Step 1: Go to RFID Cards RFID Access Enter the ID of RFID card (Only Front 10 yards) Press Add to Door Card Table. Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET Home Automation support team. PLANET online FAQs: Door Phone support team mail address: support@planet.com.tw HDP-5240PT Utility: http://www.planet.com.tw/en/support/download.php?view=8184&key=HDP5240PT#list HDP-5240PT User’s Manual: http://www.planet.com.
