Quick Guide

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for choosing PLANET HDP-1260PT. Before installing the
door phone, please verify the contents inside the package box.
The package should contain the following items:
The Vandalproof Door Phone Quick Installation Guide
Screw Kit RFID Card
RFID
Sensor
Use the corresponding RFID door card to open the
door by swiping the card. With one beep sound, the
door is opened.
DSS Key 1
Press the Direct Station Selection key to check who
the caller is before opening the doors, or talking to
him/her. (Function can be set by user.)
DSS Key 2
Press the Direct Station Selection key to check who
the caller is before opening the doors, or talking to
him/her. (Function can be set by user.)
Mic
The door phone has a built-in microphone hidden in
the pinhole located on the front panel.
2.2 Function Key LED Statuses
Type LED State
DSS Key
(Speed dial
button)
Normally on Successfully registered
2.4 Power Connector
The picture shows the two-pin connector that comes with the
system power source of DV 12V, 1A (maximum for the two-pin
connector).
1 2
+12V DC GND
2.5 Reset to Factory Default
Press and hold the button key for 9 seconds. The HDP-1260PT will
reset to factory default setting.
Number Description
Wiring Port
Description
(example above)
1
Ethernet interface: Standard RJ45
interface, 10/100M adaptive, it is
recommended to use Cat 5e of cable
Internet RJ45/PoE
2 Power interface: DC 12V, 1A input
Left: 12V+
Right: GND
3, 5
Two groups of short-circuit input
detection interfaces: For connecting
switches, infrared probes, door
magnets, vibration sensors and
other input devices
Left: IN
Right: GND
4, 6
Two groups of short-circuit output
control interface: used to control
electric locks, alarms, etc.
Left (NC):
Normally Close
Contact
Center (COM):
Common Contact
Right (NO):
Normally Open
Contact
7, 8
Door Sensor Detection: Two groups
of gate door magnetic detection
Left: DET-In
Right: GND
9
Record Out interface: Mix the device
and the sound of the far-end call.
One is the recording signal line, and
the other is the ground line.
(Please be sure to ground the line,
otherwise there will be noise.)
Left: Line2-OUT
Right: GND
2.PhysicalSpecications
Dimensions (W x D x H) 120 x 38 x 200 mm
Weight 755g (gross weight)
2.1 Front Panel
RFID Sensor
DSS Key 2
Speaker
Camera
IR LED
DSS key 1
Microphone
PoE RJ45 Port
Interface Description
IR LED
The door phone provides 4 IR LEDs for clear image
in low light condition.
Camera
The door phone has a built-in IP camera supporting
a high-resolution video of up to 1920 x 1080 pixels.
Speaker
The door phone has a built-in speaker for
convenient communication and alert use.
2.3 I/O Control Description
Open the rear case of the device and nd a row of terminal blocks
for connecting the power supply, electric lock control, etc. The
connections are shown in the table below:
       
 
10
Audio Out interface: External
active speakers for audio power
amplication. One is the audio signal
line, and the other is the ground
line.
(Please be sure to ground the line,
otherwise there will be noise.)
Left: Line1-OUT
Right: GND
11
MIC In interface: Mix the device and
the sound of the far-end call. One is
the MIC signal line, and the other is
the ground line.
(Please be sure to ground the line,
otherwise there will be noise.)
Left: MIC+
Right: MIC-
Note
The HDP-1260PT requires either IEEE 802.3af PoE or
DC Power from the power connector.
3. Installation
Wall mounting steps:
Use the given screw tool to remove the cover.
Place the back cover on the wall and mark the
four holes on the wall with a pencil.
Drill the marked four holes, place the back
cover on the wall, and slightly hammer the
plastic anchors through the four holes.
Get the power cord and network cable
connected, and secure it tightly with the
screws.
Caution
While drilling or fixing the HDP-1260PT, hold it tight
or else it may drop, thus accidentally hurting the
installer.