0/100/1000Base-T to 1000Base-SX/LX Gigabit Ethernet Media Converter User’s Manual
Trademarks Copyright © PLANET Technology Corp. 2007 Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions. FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Table of Contents Chapter 1 OVERVIEW.......................................................6 About the Gigabit Ethernet Media Converter.................6 Chapter 2 PRODUCT FEATURES.........................................7 Chapter 3 MODEL LIST....................................................9 Chapter 4 CHECKLIST.................................................... 10 Chapter 5 PRODUCT OUTLOOK....................................... 11 Chapter 6 INSTALLING THE CONVERTER.......................... 13 6.
Chapter 1 OVERVIEW Thank you for purchasing PLANET GT-80X family Gigabit Ethernet Media Converter products. This Gigabit Ethernet Media Converter is used to convert one type media signal to other type equivalent that allows two type segments connect easily, efficiently and inexpensively.
Chapter 2 PRODUCT FEATURES ● Comply with IEEE 802.3 10Base-T, IEEE 802.3u 100BaseTX, IEEE 802.3ab 1000Base-T, IEEE 802.
GT-806A15 / GT-806B15 1000Base-LX WDM interface for up to 15km (single mode 9/125µm fiber) GT-806A60 / GT-806B60 1000Base-LX WDM interface for up to 60km (single mode 9/125µm fiber)
Chapter 3 MODEL LIST Your Gigabit Ethernet Converter comes with one of the following models.
Chapter 4 CHECKLIST Your GT-80X carton should contain the following items: • The Gigabit Ethernet Converter • AC-DC Power Adapter (Output: 5VDC, 2A max.) • This user’s manual If any item is missing or damaged, please consult the dealer from whom you purchased your Gigabit Ethernet Converter. Notice: 10 GT-805A is with one vacant SFP module slot. The mini GBIC SFP module is not bundled with in the package.
Chapter 5 PRODUCT OUTLOOK Right View (GT-80X) GT-802/GT-802S GT-805A GT-806A15/B15/A60/B60 Left: Fiber-optic connector, Right: TP connector. Two LED indicators per TP, fiber port.
Rear View (GT-80X) One DC jack for DC power input.
Chapter 6 INSTALLING THE CONVERTER 6.1 Stand-alone Installation To install a GT-80X stand-alone, on a desktop or shelf, simply complete the following steps: Step 1: Turn off the power of the device/station in a network to which the GT-80X will be attached. Step 2: Ensure that there is no activity in the network. Step 3: Attach fiber cable from the GT-80X to the fiber network. TX, RX must be paired at both ends.
Figure 6-1 GT-80X installation Notice: 14 Please refer to Section 9 for detailed wiring information of the GT-80X. To prevent from optic acceptor malfunction, check the both wires / transmitter before power on the converter.
GT-805A Installation Step 1: Connect the fiber cable. Attach the duplex LC connector on the network cable into the SFP transceiver. Step 2: Attach fiber cable from the GT-805A to the fiber network. TX, RX must be paired at both ends. Step 3: Connect the 5VDC power adapter to the GT-805A and verify that the Power LED lights up. Step 7: Turn on the power of the device/station; the PWR LEDs should light when all cables are attached.
6.2 Chassis Installation and Rack Mounting To install the media converter in a 10-inch or 19-inch with standard rack, follow the instructions described below. Step 1: Place your GT-80X on a hard flat surface, with the front panel positioned towards your front side. Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis.
Caution: You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.
Chapter 7 DUPLEX MODE SUPPORT The GT-80X is one-channel media conversion between 10/100/1000Base-T and 1000Base-SX/LX. 10/100/1000BaseT port can work under Auto-negotiation mode. 1000BaseSX/LX fiber port only allow to work under fixed 1000Mbps full duplex mode.
Chapter 8 LED INDICATION LED Color PWR Green Lit: When +5VDC power detected. Green Lit: To indicate the link through that fiber port is successfully established. Blink: Indicate that the Fiber port is actively sending or receiving data over that port. Green Lit: To indicate the link through that port is successfully established. Blink: Indicate that the port is actively sending or receiving data over that port. Green Lit: When the port runs in 1000Mbps Full duplex.
Chapter 9 CABLE CONNECTION PARAMETER The wiring details are as below: Cables: Standard Fiber Type Cable Specification 1000Base-SX (850nm) Multi-mode 50/125μm or 62.5/125μm Multi-mode 50/125μm or 62.5/125μm Single-mode 9/125μm 1000Base-LX (1300nm) Wiring Distances: Standard 1000Base-SX 1000Base-LX 20 Modal Max. Bandwidth Distance (MHz * km) (meters) Fiber Diameter (micron) MM 62.5 62.5 50 50 100 200 400 500 220 275 500 550 MM 62.
Notice: The Single-mode port (1000Base-LX port) of GT-802S, GT-805A, GT-806A15/B15 and GT-806A60/B60 is complied with LX 5 kilometers and provides additional margin allowing for a 10/15/60 kilometers Gigabit Ethernet link on single mode fiber.
Chapter 10 PRODUCT SPECIFICATION The GT-80X comes with the following standard features: Model GT-802 GT-802S GT-805A GT-806A15 GT-806A60 GT-806B15 GT-806B60 SFP, LC type SC-type connector (WDM) LX Connector – Fiber SC-type connector Mode Multimode Single mode Vary on module Single mode Single mode Fiber Maximum Distance 220m / 550m 10km Vary on module 15km 60km Connector - Copper 10/100/1000Mbps RJ-45 Modes Full Duplex, auto-negotiation Packet Forwarding Rate (64bytes) 14880 pps @
Cable 10/100/1000Base-T: 1000Base-T-2-pair UTP Cat. 5/5e/6, up to 100m 1000Base-SX: 50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 220/550m 1000Base-LX: 9/125μm single-mode fiber optic cable, up to 10/15/60km Dimensions 26 x 70 x 97mm (H x W x D) Power External power adaptor 5V 2A max.
Chapter 11 POWER INFORMATION The power jack of GT-80X is with 2.5mm in the central post and required +5VDC power input. It will conform to the bundled AC-DC adapter and Planet’s Media Chassis. Should you have the problem to make the power connection, please contact your local sales representative. Please keep the AC-DC adapter as spare parts when your GT-80X is installed to a Media Chassis.
2010-AA4230-000
