6/24-Port 10/100/1000Mbps 802.
Trademarks Copyright © PLANET Technology Corp. 2015. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Energy Saving Note of the Device This power required device does not support Standby mode operation. For energy saving, please remove the power cable to disconnect the device from the power circuit. Without removing power cable, the device will still consuming power from the power source.
Table of Contents 1. Introduction................................................................................................ 5 1.1 Package Contents................................................................................. 5 1.2 Product Description............................................................................... 6 1.3 Features.............................................................................................. 7 1.4 Specification............................................
1. Introduction Thank you for purchasing PLANET 16/24-Port 10/100/1000Mbps 802.3at PoE+ Ethernet Switch, GSW-1600HP and GSW-2620HP. The descriptions of these models are shown below: GSW-1600HP 16-Port 10/100/1000T 802.3at PoE+ Gigabit Ethernet Switch GSW-2620HP 24-Port 10/100/1000T 802.3at PoE + 2-Port 1000X SFP Gigabit Ethernet Switch “802.3at PoE+ Switch” mentioned in this Guide refers to the GSW-1600HP and GSW-2620HP. 1.1 Package Contents Open the box of the 802.
1.2 Product Description Centralized Power Management for Gigabit Ethernet PoE Networking To facilitate high power PoE network applications with Gigabit speed transmission, the 802.3at PoE+ Switch features high-performance Gigabit IEEE 802.3af PoE (up to 15.4W) and IEEE 802.3at High-power PoE (up to 30.8W) capabilities on all ports. By offering reliable switching technology and advanced networking features, the 802.
ceiling or any unreachable place. It helps to lower the installation costs and simplify the installation effort. All RJ45 copper interfaces of the 802.3at PoE+ Switch support 10/100/1000Mbps auto-negotiation for optimal speed detection through RJ45 Category 6, 5 or 5e cables. It also supports standard auto-MDI/ MDI-X that can detect the type of connection to any Ethernet device without requiring special straight-through or crossover cables.
Automatic address learning and address aging Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az) Hardware 19-inch desktop size, 1U height LED indicators for PoE ready and PoE activity Ethernet Link Energy-saving technology - Link down power saving - Intelligent scale power based on cable length 1.4 Specifications Model GSW-1600HP GSW-2620HP 16 auto-MDI/MDI-X ports 24 auto-MDI/MDI-X ports Hardware Specifications 10/100/1000BASE-T Copper Ports 802.3af / 802.
Enclosure Metal Weight Power Requirements 2.54kg 2.85kg AC 100~240V, 50/60Hz, 3.5A max. 100~240V AC, 50/60Hz, 4A (max.) Power Consumption/ Dissipation Max. 260 watts/885 BTU Thermal Fan 2 Power over Ethernet PoE Standard IEEE 802.3af Power over Ethernet/PSE IEEE 802.3at Power over Ethernet Plus/PSE PoE Power Output Per port 52V DC, 300mA. max. 15.4 watts (IEEE 802.3af) Per port 52V DC, 600mA. max. 30 watts (IEEE 802.
2. Hardware Description This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps – in the same switch and automatically distinguishes the speed of incoming connection. This section describes the hardware features of 802.3at PoE+ Switch. For easier management and control of the 802.3at PoE+ Switch, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the 802.
Per 10/100/1000BASE-T Port LED Color Function Green Lights to indicate the link through that port is successfully established at 1000Mbps. Blinks to indicate that the Switch is actively sending or receiving data over that port. 10/100 LNK/ACT Orange Lights to indicate the link through that port is successfully established at 10/100Mbps. Blinks to indicate that the Switch is actively sending or receiving data over that port.
AC Power Receptacle For compatibility with electrical outlet standard in most areas of the world, the 802.3at PoE+ Switch’s power supply automatically adjusts to line power in the range of 100-240V AC and 50/60Hz, 3.5A/4A. Plug the female end of the power cord firmly into the receptacle on the rear panel of the 802.3at PoE+ Switch and the other end into an electrical outlet and the power will be ready. Power Notice 12 1.
3. Hardware Installation Start up Please refer to the followings for your cabling: 10/100/1000BASE-T All 10/100/1000BASE-T ports come with Auto-Negotiation capability. They automatically support 1000BASE-T, 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100/1000BASE-T ports, and then turn on the 802.3at PoE+ Switch.
3.1 Desktop Installation To install the 802.3at PoE+ Switch on desktop, simply follow the following steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the 802.3at PoE+ Ethernet Switch, as shown in Figure 3-1. Figure 3-1: Attaching the Rubber Feet to the 802.3at PoE+ Switch Step2: Place the 802.3at PoE+ Switch on desktop near an AC power source. Step3: Keep enough ventilation space between the 802.3at PoE+ Switch and the surrounding objects.
3.2 Rack Mounting To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below. Step1: Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side. Step2: Attach a rack-mount bracket to each side of the 802.3at PoE+ Switch with supplied screws attached to the package. Figure 3-2 shows how to attach brackets to one side of the 802.3at PoE+ Switch. Figure 3-2: Attaching the Brackets to the 802.3at PoE+ Switch.
Step6: 3.3 Proceed with Steps 4 and 5 of session 3.1 Desktop Installation to connect the network cabling and supply power to your Switch. Installing the SFP Transceiver (GSW-2620HP only) The sections describe how to insert an SFP transceiver into an SFP slot of the GSW-2620HP. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the GSW2620HP, as the Figure 3-4 shows.
MGB-LA10 SFP-Port 1000BASE-LX (WDM,TX:1310nm) - 10km MGB-LB10 SFP-Port 1000BASE-LX (WDM,TX:1550nm) - 10km MGB-LA20 SFP-Port 1000BASE-LX (WDM,TX:1310nm) - 20km MGB-LB20 SFP-Port 1000BASE-LX (WDM,TX:1550nm) - 20km MGB-LA40 SFP-Port 1000BASE-LX (WDM,TX:1310nm) - 40km MGB-LB40 SFP-Port 1000BASE-LX (WDM,TX:1550nm) - 40km Note It is recommended to use PLANET SFP on the GSW-2620HP. If you insert an SFP transceiver that is not supported, the GSW-2620HP will not recognize it. 1.
3.4 Product Applications Department/Workgroup PoE Switch: Providing 16/24 PoE in-line power interfaces, the 802.3at PoE+ Switch can easily build a power that centrally controls IP phone system, IP camera system and wireless AP group for enterprises. Cameras can be installed around the corner in the company or campus for surveillance demands. Without the power-socket limitation, the Switch makes the installation of cameras more easily and efficiently. 802.
3.5 Power over Ethernet Powered Devices 3~5 watts Voice over IP Phones As many as PoE VoIP phones, ATAs and other Ethernet/ non-Ethernet end-devices can be installed, but UPS is needed for uninterrupted power system and power control system. Wireless LAN Access Points Access points can readily be installed in museums, sightseeing sites, airports, hotels, campuses, factories and warehouses.
30 watts Note 20 High Power Speed Dome This state-of-the-art design fits very nicely in various network environments like traffic centers, shopping malls, railway stations, warehouses, airports and production facilities for the most demanding outdoor surveillance applications. Electrician is not needed to install AC sockets. Since each port of the 802.3at PoE+ Switch supports 52V DC PoE power output, please make sure the Powered Device’s (PD) acceptable DC power range is from 52V DC.
4. Power over Ethernet Overview What is PoE? PoE is an abbreviation of Power over Ethernet. The PoE technology means a system safely transmits both power and data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with Cat3 cable for low power levels.
intermediary device between a non PoE capable switch and a PoE device, it is called a mid-span. An external PoE injector is a mid-span device. Powered Device A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP phones, and IP cameras. Many powered devices have an auxiliary power connector for an optional, external power supply.
The data pairs are used. Since Ethernet pairs are transformers coupled at each end, it is possible to apply DC power to the center tap of the isolated transformer without upsetting the data transfer. In this mode of operation, the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
5. Troubleshooting This chapter contains information to help you solve issues. If the 802.3at PoE+ Switch is not functioning properly, make sure the 802.3at PoE+ Switch was set up according to instructions in this manual. The Link LED is not lit. Solution: Check the cable connection and also try to swap one new cable. 1000BASE-T port link LED is lit, but the traffic is irregular. Solution: Check that the attached device is not set to dedicate full duplex.
Appendix A Networking Connection A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T PIN NO MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. A.
The standard cable, RJ45 pin assignment The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
EC Declaration of Conformity For the following equipment: *Type of Product: *Model Number: 16-Port 10/100/1000Mbps 802.3at PoE Switch (220 Watts) GSW-1600HP * Produced by: Manufacturer‘s Name: Manufacturer‘s Address: Planet Technology Corp. 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
EC Declaration of Conformity For the following equipment: *Type of Product: 24-Port 10/100/1000T 802.3at PoE + 2-Port 1000X SFP Gigabit Ethernet Switch *Model Number: GSW-2620HP * Produced by: Manufacturer‘s Name: Manufacturer‘s Address: Planet Technology Corp. 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.).
