User's Manual
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000BASE-T RJ45 ports on the
front of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers, etc.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard
rack, follow the instructions described below:
Step 1: Place your Gigabit Ethernet Switch on a hard at
surface, with the front panel positioned towards
your front side.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please follow the
procedure below:
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on the desktop,
simply follow these steps:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on the desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
When choosing a location, please keep in mind
the environmental restrictions discussed in
Section 3 under Product Specifications.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 5 shows how to attach brackets to
one side of the Gigabit Ethernet Switch.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Standard
Flow Control Off
Extend
VLAN
GSW-2401
1 3 5 7 9 11 13 15
2
PWR
4 6 8 10 12 14 16
17 19 21 23
18 20 22 24
ACT1000 LNK
ACT10/100LNK
2 4 6 8
1 3 5 7
10 12 14 16
9 11 13 15
18 20 22 24
17 19 21 23
24-Port 10/100/1000T Gigabit
Ethernet Switch
Figure 5: Attaching the brackets to the Gigabit Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to the
parts by using incorrect screws would invalidate
your warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second
bracket to the opposite side.
Step 5: After the brackets are attached to the Gigabit
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in
Figure 6.
24-Port 10/100/1000T Gigabit Ethernet Switch
GSW-2401
ACT1000 LNK
ACT10/100LNK
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 23
1 3 5 7 9 11 13 15 17 19 21 23
PWR
2 4 6 8 10 12 14 16 18 20 22 24
Standard
Flow Control Off
Extend
VLAN
GSW-2401
1 3 5 7 9 11 13 15
2
PWR
4 6 8 10 12 14 16
17 19 21 23
18 20 22 24
ACT1000 LNK
ACT10/100LNK
2 4 6 8
1 3 5 7
10 12 14 16
9 11 13 15
18 20 22 24
17 19 21 23
24-Port 10/100/1000T Gigabit
Ethernet Switch
Figure 6: Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Desktop
Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
I hereby confirm that the following equipment complies with the requirements set out in the
Council Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility Directive on (2014/30/EU), and Low Voltage Directive on
(2014/35/EU).
Type of Product:
16-Port 10/100/1000T Gigabit Ethernet Switch
24-Port 10/100/1000T Gigabit Ethernet Switch
Models:
GSW-1601
GSW-2401
Produced by:
Manufacturer’s Name: Planet Technology Corporation
Manufacturer’s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan, R.O.C.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015 + AC:2016)
EN61000-3-2 (2014)
EN61000-3-3 (2013)
EN 55035 (2017)
EN 62368-1 (2014 + A11:2017)
Person responsible for making this declaration
Name: Kent Kang
Title: Director
Taiwan
Oct. 23, 2020
Country
Date
Legal Signature
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Web site rst to check
if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
support@planet.com.tw
Copyright © PLANET Technology Corp. 2020
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.