GST-80x Series (V2) User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Item Description
OAM Setting ProvidesOAMCongurationonGST-80x.
Ingress Rate
Limit
DenesreceiverateforbandwidthcontrolfromTP
and Fiber ports of GST-80x.
Egress
Shaping
Denestransmitrateforbandwidth controlfrom
TP and Fiber ports of GST-80x.
Note
Please refer to the manual of Management Media
Coverter Chassis (MC-1610MR/MC-1610MR48) for
more details about OAM Setting and bandwidth control
function.
7. Cable Connection Parameter
The wiring details are shown below:
Duplex Connection Limitation (max.)
Twisted Pair
Half/Full
Node to Node
Node to Switch/Hub
100 meters
Fiber Optic Cables:
Standard
(Wavelength)
1000BASE-SX
(850nm)
1000BASE-LX
(1310nm)
Fiber Type & Cable
Specications
Multi-mode 50/125μmor62.5/125μm
Single-mode 9/125μm
8.ProductSpecications
Model GST-802 GST-802S GST-805A
HardwareSpecications
Copper Interface
10/100/1000BASE-T RJ45 port, Auto-MDI/MDI-X,
Twisted Pair
Optic Interface
1000BASE-SX
Multi-mode,
Duplex SC
1000BASE-LX
Single mode,
Duplex SC
1000BASE-X
SFP slot
Optic Wavelength 850nm 1310nm NA
5. Link fault pass-through (LFP)
The LFP function includes the Link-Fault-Passthrough function
(LLCF/LLR) and the DIP Switch design. LLCF/LLR can immediately
alarm administrators the issue of the link media and provide
ecient solution to monitor the network. The DIP Switch will
disable or enable the LFP function.
LLCF (Link Loss Carry Forward) means when a device is connected
tothe converterandtheTPline loses the link, the converter’sber
will disconnect transmission link. LLR (Link Loss Return) means
whenadeviceisconnectedtotheconverterand theber lineloses
thelink,theconverter’sberwilldisconnecttransmissionlink.
Note
LFP function is ON by default setting. If you are
familiar with the network installation and for
diagnostic purpose (i.e. check which end is broken),
you can turn it off and reset the converter to make
it take effect. Otherwise, please keep it in the default
position.
6. Duplex Mode Support
The GST-80x Smart Media Converter TP port supports triple speeds
-- 10/100/1000BASE-T – in the auto-negotiation mode. It will auto
detect the link speed and the duplex mode by default with its link
partner. The ber port (1000BASE-SX/LX) runs at 1000Mbps in
the full-duplex transmission in the auto-negotiation mode. Please
also check the setting of the link partner.
Fiber Maximum
Distance
220/550m 20km
Vary of SFP
module
Speed
Twisted-
pair
10/20Mbps for Half/Full Duplex
100/200Mbps for Half/Full Duplex
2000Mbps for Full Duplex
Fiber-optic 2000Mbps for Full Duplex
Cable
Twisted-
pair
10BASE-T: 2-pair UTP Cat. 3,4,5, up to 100 m
100BASE-TX: 2-pair UTP Cat. 5, up to 100 m
1000BASE-T: 4-pair STP Cat 5 up to 100m
Fiber-optic
Cable
50/125μmor62.5/125μm multi-modebercable,
up to 220/550m/2km.
9/125μmsingle-modecable,provideslongdistance
for10/20/40/80/120km(varyonbertransceiveror
SFP module)
LED Indicator
PWR (Green)
TP: 1000, LINK/ACT (Green)
Fiber: LINK/ACT (Green)
DIP Switch
Fiber (Auto-negotiation/Manual),
LFP (Disable/Enable)
Power Consumption 2.3 watts/7.8BTU (maximum)
OAM TS-1000, IEEE 802.3ah terminal
Jumbo Frame size 16K
Power Input DC 5V/2A
Dimensions
(W x D x H)
93 x 80 x 26 mm
Weight 207g
Operating
Environment
Temperature: 0~50 degrees C
Humidity: 5~95% non-condensing
Storage
Environment
Temperature: -10~70 degrees C
Humidity: 5~95% non-condensing
Emissions FCC Class A, CE Class A
Standards
IEEE 802.3, 10BASE-T
IEEE 802.3u, 100BASE-TX
IEEE 802.3ab, 1000BASE-T
IEEE 802.3z, 1000BASE-SX/LX
IEEE 802.3ah OAM
Model GST-806A15 GST-806B15 GST-806A60 GST-806B60
HardwareSpecications
Copper Interface
10/100/1000BASE-T RJ45 port, Auto-MDI/MDI-X,
Twisted Pair
Optic Interface
1000BASE-BX Single mode WDM
Simplex SC
Optic Wavelength
TX:1310nm
RX:1550nm
TX:1550nm
RX:1310nm
TX:1310nm
RX:1550nm
TX:1550 nm
RX:1310 nm
Fiber Maximum
Distance
20km 60km
Speed
Twisted-
pair
10/20Mbps for Half/Full Duplex
100/200Mbps for Half/Full Duplex
2000Mbps for Full Duplex
Fiber-
optic
2000Mbps for Full Duplex
Cable
Twisted-
pair
10BASE-T: 2-pair UTP Cat. 3,4,5, up to 100 m
100BASE-TX: 2-pair UTP Cat. 5, up to 100 m
1000BASE-T: 4-pair STP Cat 5 up to 100m
Cable
Fiber-
optic
Cable
9/125μmsingle-modecable,provideslongdistancefor
20/60km
LED Indicator
PWR (Green)
TP: 1000, LINK/ACT (Green)
Fiber: LINK/ACT (Green)
DIP Switch
Fiber (Auto-negotiation/Manual),
LFP (Disable/Enable)
Power
Consumption
2.3 watts/7.8BTU (maximum)
OAM TS-1000, IEEE 802.3ah terminal
Jumbo Frame size 16K
Power Input DC 5V/2A
Dimensions
(W x D x H)
93 x 80 x 26 mm
Weight 207g
Operating
Environment
Temperature: 0~50 degrees C
Humidity: 5~95% non-condensing
Storage
Environment
Temperature: -10~70 degrees C
Humidity: 5~95% non-condensing
Emissions FCC Class A, CE Class A
Standards
IEEE 802.3, 10BASE-T
IEEE 802.3u, 100BASE-TX
IEEE 802.3ab, 1000BASE-T
IEEE 802.3z, 1000BASE-LX
IEEE 802.3ah OAM