GST-80x Series (V2) User Manual
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Checklist
Your GST-80x carton should contain the following items:
The descriptions of the Smart Media Converter series are shown
below:
GST-802
10/100/1000BASE-T to 1000BASE-SX Smart Gigabit
Media Converter
GST-802S
10/100/1000BASE-T to 1000BASE-LX Smart Gigabit
Media Converter
GST-805A
10/100/1000BASE-T to 1000BASE-SX/LX Smart
Gigabit Media Converter (mini-GBIC,SFP)
GST-806A15
10/100/1000BASE-T to 1000BASE-LX WDM Smart
Gigabit Media Converter-TX: 1310 –20km
GST-806B15
10/100/1000BASE-T to 1000BASE-LX WDM Smart
Gigabit Media Converter-TX: 1550 –20km
GST-806A60
10/100/1000BASE-T to 1000BASE-LX WDM Smart
Gigabit Media Converter-TX:1310 – 60km
GST-806B60
10/100/1000BASE-T to 1000BASE-LX WDM Smart
Gigabit Media Converter-TX: 1550 – 60km
AC-DC Power Adapter (Output: 5V DC, 2A max.)
This User’s Manual
If any item is missing or damaged, please consult the dealer from
whom you purchased your Gigabit Ethernet Media Converter.
Note
The GST-805A comes with one vacant SFP module
slot. The mini GBIC SFP module is not bundled in the
package.
Hardware:
Used as a stand-alone device or work with Managed Media
Converter Chassis for up to 16 converters with redundant power
supply for optional expansion use
LED indicators for converter status
Choice of ber connectors from SC, LC, WDM, multi-mode/
single-modeber/1000BASE-SX/LXminiGBICmodule
EMI standards complies with FCC, CE class A
3. Product Outlook
Right View: There are one RJ45 twisted-pair jack (Auto-MDI/
MDI-X),oneber-opticconnector(vary by model) and four LED
indicators.
Left View: There is one DC jack for DC 5V power adapter.
Power Information
The power jack of Smart Media Converter measures 2.5mm in the
central post and requires +5VDC power input. It conforms to the
bundled AC-DC adapter and PLANET’s Media Chassis. Should you
have any issue of power connection, please contact your local sales
representative.
The AC-DC adapter is used as a spare part when your Smart Media
Converter is installed to a Media Chassis.
2.5mm
DC Receptacle 2.5mm +5V for each slot
DC receptacle is 2.5mm wide that conforms to the Gigabit
Ethernet Media Converter’s 2.5mm DC jack’s central post.
Do not install any improper unit.
Note
When two converters are used at the same time, they
MUST be set to the “Forced” mode; if not, either
mode can be set to according to your requirements.
The Management Media Coverter Chassis-MC-1610MR/
MC-1610MR48 displays the status of GST-80x; besides, the
Management Media Coverter Chassis controls the function and
OAM/Bandwidth setting through its management system.
Through the Management Media Converter Chassis System, you
can control the setting of GST-80X, such as device (disable/enable),
LFP (disable/enable), UTP (auto-negotiation/manual), speed
(10/100/1000Mbps), duplex mode (half/full duplex mode) and ow
control(disable/enable),andber(auto-negotiation/manual).
LED Indicators
LED Color Status Indication
PWR Green
LightsO Powero.
Lights On
Power on when +5V DC is
detected.
Fiber
LNK/ACT
Green
LightsO
Indicates the link through that
port is not established.
Lights On
Indicates the link through
that port is successfully
established.
Lights Blink
Indicates that port is actively
sending or receiving data.
TP
LINK/ACT
Green
LightsO
The link through that port is
not established.
Lights On
The link through that port is
successfully established.
Lights Blink
Indicates that port is actively
sending or receiving data.
TP 1000 Green
LightsO
Indicates that the port is
operating at 10Mbps or
100Mbps.
Lights On
Indicates that the port is
operating at 1000Mbps.
2. Product Features
GST-80x Smart Media Converter:
Standards:
Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-
TX, IEEE 802.3ab 1000BASE-T, IEEE 802.3z 1000BASE-SX/LX
Ethernet Standard
Interface:
One 10/100/1000BASE-T port with RJ45 connector
One 1000BASE-SX/LX port with LC/SC/WDM connector
supportingmulti-modeorsingle-modeberopticcable
Auto-negotiation and Auto-MDI/MDI-X for 10/100/1000BASE-T
port
Layer 2 Features:
Flow control: Back pressure for half duplex and IEEE 802.3x for
full duplex
Full wire-speed forwarding rate
16K Jumbo Frame size supported
Link Loss Return (LLR) switch on each ber optic to aid in trou-
bleshooting remote network connections
Link Loss Carry Forward (LLCF) works with LLR in diagnosing
network connections
Smart Management:
Provides DIP switch for ber (Auto-negotiation/Manual) and LFP
function (Disable/Enable) setting
Manageable through Managed Media Converter Chassis System
(MC-1610MR/MC-1610MR48)
Bandwidth control/TS-1000 OAM/IEEE 802.3ah OAM/Loop Back
Test function provided with MC-1610MR/MC-1610MR48 Managed
Media Converter Chassis System
GST-802/GST-802S:
Gigabit Ethernet Converter
10/100/1000Base-T to 1000Base-SX/LX
1000
10/100/1000Base-T
1000Base-SX/LX
PWR
TP
Fiber
LNK
ACT
5V DC
Gigabit Ethernet Converter
10/100/1000Base-T to 1000Base-SX/LX
GST-805A:
Gigabit Ethernet Converter
10/100/1000Base-T to 1000Base-SX/LX
1000
10/100/1000Base-T
Mini-GBIC
PWR
TP
Fiber
LNK
ACT
5V DC
Gigabit Ethernet Converter
10/100/1000Base-T to 1000Base-SX/LX
GST-806A15/GST-806B15/GST-806A60/GST-806B60:
Gigabit Ethernet Converter
10/100/1000Base-T to 1000Base-LX
1000
10/100/1000Base-T
WDM
PWR
TP
Fiber
LNK
ACT
Gigabit Ethernet Converter
10/100/1000Base-T to 1000Base-LX
5V DC
4. Managing the Media Converter
This section describes how to operate the GST-80x Smart Media
Converter through its DIP Switch and Web Management Media
converter chassis. Before using the GST-80x smart function, please
read this chapter carefully.
Please refer to the table below for DIP switch usages.
1 2
ON
Switch 1: onForce Mode
oAuto
Negotiation Mode
Switch 2: onLFP enable
oLFP disable
DIP Switch Mode Description
DIP Switch 1
On
It will be in the Forced Mode when
switched to “On”.
O
It will be in the Auto-Negotiation mode by
defaultwhenswitchedto“O”.
DIP Switch 2
On
When switched to “On”, LFP will be enabled
by default.
O
Whenswitchedto“O”,LFPwillbe
disabled.
Item Description
Device To enable or disable per GST-80x Converter board.
LFP
To enable or disable the LFP function from GST-80x
Converter board.
TP AN
Mode
To set the UTP port to Auto-negotiation or Forced
Mode.
TP Speed
To set the UTP port to 1000Mbps, 100Mbps or
10Mbps.
TP Duplex
To set the UTP port to Full duplex or Half duplex
mode.
TP FC
To set the Flow Control of the UTP port to enable or
disable.
Fiber AN
Mode
To set the Fiber port to Auto-negotiation or Forced
Mode.
Note
Please note that if the converter is connected with
a switch which is in the auto negotiation mode, the
converter must also be set to the auto neogtiaiton
mode. If both devices are conveters, auto negotiation
mode must be disabled.
To easily know the TP/Fiber port link status of the other end of the
device, the Management Media Converter Chassis System provides
OAM Setting that includes TS-1000 OAM/IEEE 802.3ah OAM/Loop
Back Test function. In addition, the bandwidth control function
allows to dene the available transmit/receive bandwidth on TP/
Fiber port of GST-80x.