(V4) User Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET GSD-908HP 8-Port
10/100/1000T 802.3at PoE + 1-Port 10/100/1000T Desktop
Switch. “802.3at PoE+ Switch” mentioned in this Guide
refers to the GSD-908HP.
Open the box of the 802.3at PoE+ Switch and carefully unpack
it. The box should contain the following items:
The 802.3at PoE+ Switch x 1 User’s Manual x 1
AC to DC Power
Adapter x 1
Power Cord x 1 Rubber Feet x 4
 Switching
 Hardware-based 10/100/1000Mbps auto-negotiation and
auto MDI/MDI-X
 Flow control for full duplex operation and back pressure
for half duplex operation
 Integrates address look-up engine, supporting 2K absolute
MAC addresses
 9K jumbo frame supports all speeds (10/100/1000Mbps)
 IEEE 802.1Q VLAN transparency
 Automatic address learning and address aging
 Solid DIP switch to isolate ports to prevent broadcast
storm and defend DHCP spoong
 Hardware
 Made of metal, desktop size and wall-mount design
 LED indicators for system power, per port PoE-in-Use (Port
1 to port 8), per port Link/Act (10/100/1000Mbps, port 1
to port 9).
 55V DC, 2.3A external power adapter
 FCC, CE Class A compliant
4. Hardware Introduction
4.1 Front Panel
The front panel of the 802.3at PoE+ switch consists of 9
auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED
indicators are also located on the front panel of the 802.3at
PoE+ switch.
1 2 3 4 5 6 7 8 9-
GSD-908HP
PWR
Uplink
PoE-in-Use ACTLNK
Default
VLAN
Figure 4-1: GSD-908HP Switch Front Panel
The front panel of 802.3at PoE+ switch provides one DIP
switch for “Default” or “VLAN” mode selection. The detailed
descriptions are shown in the following table.
DIP Switch Mode Function
Default
This mode makes the 802.3at PoE+
Switch operate as a general switch and all
ports operate at 10/100/1000Mbps auto-
negotiation.
VLAN
This mode makes the 802.3at PoE+ Switch
operate as a VLAN isolation switch and
port 1 to port 8 will isolate respectively.
Port 1 to port 8 can only communicate
with port 9 (uplink port).
Weight 419g
Power Requirements 55V DC, 2A
Power Consumption/
Dissipation
Max. 100 watts / 341BTU
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/
PSE
IEEE 802.3at Power over Ethernet
Plus/PSE
PoE Power Supply
Type
End-span: 1/2 (+), 3/6 (-)
PoE Power Output
Per port 54V DC, 300mA. max.
15.4 watts (IEEE 802.3af)
Per port 54V DC, 600mA. max.
30 watts (IEEE 802.3at)
PoE Power Budget 100 watts
Number of PDs, 7
watts
8
Number of PDs, 15.4
watts
6
Number of PDs, 30
watts
3
If any of these pieces are missing or damaged, please contact
your dealer immediately; if possible, retain the carton including
the original packing material, and use them again to repack
the product in case there is a need to return it to us for repair.
2. Product Features
 Physical Port
 9-port 10/100/1000BASE-T Gigabit RJ45 copper
 Power over Ethernet
 Complies with IEEE 802.3at Power over Ethernet Plus
 Complies with IEEE 802.3af Power over Ethernet
 Up to 8 ports of IEEE 802.3af/802.3at devices powered
 Supports PoE Power up to 30.8 watts for each PoE port
 Each port supports 54V DC power to PoE powered device
 100-watt PoE budget
 Auto detects powered device (PD)
 Circuit protection prevents power interference between
ports
 Remote power feeding up to 100m
3.ProductSpecications
Model GSD-908HP
Hardware Specications
10/100/1000BASE-T
Copper Ports
9 auto-MDI/MDI-X ports
802.3af/802.3at
PoE+ Injector Port
8
Switch Architecture Store-and-Forward
Switch Fabric 18Gbps
Switch
Throughput@64bytes
13.3Mpps
MAC Address Table 2K entries
Jumbo Frame 9216 bytes
Flow Control
IEEE 802.3x pause frame for full
duplex; back pressure for half duplex
LED
System: Power (Amber)
10/100/1000T RJ45 Interfaces
PoE-in-Use (Amber)
10/100/1000 LNK/ACT (Green)
DIP Switch
Default mode for switch
architecture
VLAN mode for Port-based VLAN
Dimensions
(W x D x H)
168 x 94 x 32 mm
Enclosure Metal
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3x ow control and back
pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet
Plus
Environment
Operating
Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95%
(non-condensing)
Storage
Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95%
(non-condensing)
Note
After changing the mode, you need to manually
restart the 802.3at PoE+ Switch to make the
corresponding configuration take effect.
4.2 LED Indicators
 System
LED Color Function
PWR Amber Lights to indicate the Switch has power.
 Per 10/100/1000BASE-T Port
LED Color Function
PoE in Use Amber
Lights to indicate the port is providing
PoE in-line power.
10/100/1000
LNK/ACT
Green
Lights to indicate the link through
that port is successfully established at
10/10/1000Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.