(V3) User Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
Gigabit Ethernet Switch x 1 User’s Manual x 1
Power Cord x 1 Rubber Feet x 4
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair
3. Hardware Introduction
3.1 Switch Front Panel
Figure 3-1 shows the front panel of the GSD-805
1 2 3 4 5 6 7 8
ACTLNK
GSD-805
PWR
Figure 3-1: GSD-805 Front Panel
3.2 LED Indicators
System
LED Color Function
PWR Green Lights: Indicates the Switch has power.
Per 10/100/1000Mbps Port
LED Color Function
LNK/
ACT
Green
Light: Indicates the link through that
port is successfully established at
10/100/1000Mbps.
OFF: Indicates that the Switch is actively
sending or receiving data over that
port.
Step 4: Connect your GSD-805 to network devices.
A. Connect one end of a standard network cable to
Port 1 or Port 8 on the front of the Gigabit Switch.
B. Connect the other end of the cable to a network
video recorder, workstation or router.
Note
Cable Distance for Switch
The UTP/STP cable distance between the GSD-805
and PC/PD devices should not exceed 100 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used for 10/100Mbps
operation. To reliably operate your network at
1000Mbps, you must use an unshielded twisted-
pair (UTP) Category 5/5e cable, or better data
grade cable. While a Category 3 or 4 cable may
initially seem to work, it will soon cause data loss.
Step 5: Supply power to the GSD-805.
A. Connect one end of the power cable to the
Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the GSD-805 receives power, the Power LED should
remain solid Green
3.4 DIP Switch - VLAN Isolation Feature
The GSD-805 has one feature called VLAN Isolation. When
switching the DIP to the “Enable” position, port 1 to port 7
wouldn’t able to communicate with each other.
1 2 3 4 5 6 7 8
ACTLNK
GSD-805
PWR
Port Isolation
Port 1 to Port 7 only can communicate with Uplink Port 8
1 2 3 4 5 6 7 8
ACTLNK
GSD-805
PWR
Port-based VLAN
Uplink
2. Product Features
RJ45 Interface
 8 10/100/1000Mbps Gigabit Ethernet ports
 Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u 100BASE-
TX, IEEE 802.3ab 1000BASE-T
 Supports auto MDI/MDI-X function
Switching
 Hardware-based 10/100Mbps in half/full duplex mode and
1000Mbps in full duplex mode, ow control, and auto-
negotiation
 Features Store-and-Forward mode with wire-speed ltering
and forwarding rates
 IEEE 802.3x ow control for full duplex operation and
backpressure for half duplex operation
 Integrated address look-up engine, supporting 8K absolute
MAC addresses
 9K jumbo packet size
 Automatic address learning and address aging
 Supports VLAN isolation mode
 Supports CSMA/CD protocol
Hardware
 Metal housing, desktop size and wall-mount design
 LED indicators for system power, Link/Act port
 Internal power adapter 100-240V AC, 50/60Hz, 0.2A
 FCC, CE Class B compliant
3.3 Switch Rear Panel
Figure 3-2 shows the rear panel of the GSD-805 where there is
a 100-240V, 50/60Hz AC inlet power socket.
100~240V AC, 50/60Hz
DisableEnable
Port-based VLAN Function
Please power off before switching DIP.
Figure 3-2: GSD-805 Rear Panel
Power
Notice
1. The device is a power-required device, meaning
it will not work till it is powered. If your
networks should be active all the time, please
consider using UPS (Uninterrupted Power Supply)
for your device. It will prevent you from network
data loss or network downtime.
2. In some areas, installing a surge suppression
device may also help to protect your GSD-805
from being damaged by unregulated surge or
current to the GSD-805 or the power adapter.
4. Installing the Switch
This part describes how to install your GSD-805 and make
connections to it. Please read the following topics and follow
the procedures as presented.
Note
The GSD-805 does not need software configuration.
Desktop Installation
To install the GSD-805 on desktop, simply follow the following
steps:
Step 1: Attach the rubber feet to the recessed areas on the
bottom of the GSD-805.
Step 2: Place the GSD-805 on desktop near AC power source.
Step 3: Keep enough ventilation space between the GSD-805
and the surrounding objects
Note
When choosing a location, please keep in mind the
environmental restrictions discussed in Chapter 5--
Product Specifications.
Wall-mount Installation
Step 1: Please nd the wall that can mount the GSD-805.
Step 2: Install two screws on the wall.
Step 3: Hang the GSD-805 on the screws from the wall.
Step 4: Repeat step 5 of Desktop Installation for power
supply to the GSD-805.
Note
Before mounting the device to the wall, please
check the location of the electrical outlet and the
length of the Ethernet cable.
RJ45
UTP Cable
100~240V AC, 50/60Hz
DisableEnable
Port-based VLAN Function
Light: Indicates the link through that port is
successfully established at 10/100/1000Mbps.
OFF: Indicates that the Switch is actively sending
or receiving data over that port.