User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
GSD-604HP User's Manual Rubber Feet x 4
54V Power Adapter Power Cord
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.
 Switching
• Hardware-based 10/100/1000Mbps, auto-negotiation and
autoMDI/MDI-X
• Flow control for full duplex operation and back pressure
for half duplex operation
• Integratesaddress look-upengine, supporting 4K absolute
MAC addresses
• Automaticaddresslearningandaddressaging
• Supportsport-basedVLAN
 Hardware
• LEDindicatorsforPoEready/activityandLINK/ACT
• One54VDCpowerjack
• Fanlessdesign
3. Switch Front Panel
Figure3-1showsthefrontpanelofthePoESwitch
GSD-604HP
PoE
1
Extend
Standard
2 3 4
5 Uplink 6
ACTLNK
PoE-in-Use
PWR
Default
VLAN
1 2 3 4
ON
Figure 3-1: Front Panel
6.2. Extended Feature
Standard
ThismodemakesthePoESwitchoperateas
ageneralswitchandallPoEportsoperateat
10/100/1000Mbpsinauto-negotiation.
Extend
Thismodewiththedatarateof10Mbpsmakesthe
PoESwitch’sPorts1to4supportalong-distance
data transmission of up to 250 meters.
5. Switch Rear Panel
Figure5-1showstherearpanelofthePoESwitch.
54-56V
Figure 5-1: Rear Panel
Power
Note
1.The device is a power-required device, meaning
it will not work till it is powered. If your
networks should be active all the time, please
consider using UPS (Uninterrupted Power
Supply) for your device. It will prevent you from
network data loss or network downtime.
2. In some areas, installing a surge suppression
device may also help to protect your GSD-
604HP from being damaged by unregulated
surge or current to the GSD-604HP or the power
adapter..
2. Product Features
 RJ45 Interface
• 6 10/100/1000BASE-T RJ45 ports with 4-port IEEE
802.3af/atinjectorfunction
 PoweroverEthernet
• Complies with IEEE 802.3af/at Power over Ethernet end-
spanPSE
• Upto4portsofIEEE802.3af/802.3atdevicespowered
• SupportsPoEpowerupto30wattsforeachPoEport
• Eachportsupports54VDCpowertoPoEpowereddevice
• 65-wattPoEbudget
• Autodetectspowereddevice(PD)
• Circuit protection prevents power interference between
ports
• Remote power feeding up to 100m in standard mode and
250m in extend mode
4 LED Indicators
 System
LED Color Function
PWR Orange
Lights: Indicates the Switch has power.
TheLEDisshownonPort6
 Per 10/100/1000Mbps Port
LED Color Function
LNK Green
Lights: Indicates the link through that
port is successfully established at
10/10/1000Mbps.
Blinks: IndicatesthattheSwitchisactively
sendingorreceivingdataoverthat
port.
 PoE-in-Use Port
LED Color Function
PoE Orange
Lights:Indicatestheportisproviding54V
DC in-line power.
6. DIP Switch
6.1 Port-based VLAN Feature
TheGSD-604HPhasonefeaturecalledPort-basedVLAN. When
switching the DIP to the “Enable” position, port 1 to port 4
wouldn’tabletocommunicatewitheachother.
GSD-604HP
PoE
1
Extend
Standard
2 3 4
5 Uplink 6
ACTLNK
PoE-in-Use
PWR
Default
VLAN
1 2 3 4
ON
Port 1 to Port 4 can only communicate with Uplink Port 5 &
Port 6.
Port-based VLAN
Uplink Ports
GSD-604HP
PoE
1
Extend
Standard
2 3 4
5 Uplink 6
ACTLNK
PoE-in-Use
PWR
Default
VLAN
1 2 3 4
ON
7. Installing the Switch
This part describes how to install your PoE Switch and make
connections to it. Please follow the procedures:
Desktop Installation
To install the PoE Switch on desktop, simply follow the
following steps:
Step 1: Attach the rubber feet to the recessed areas on the
bottomofthePoESwitch.
Step 2: Place the PoE Switch on desktop near AC power
source for its power adapter.
Step 3: Keep enough ventilation space between the PoE
Switchandthesurroundingobjects.
Note
When choosing a location, please keep in mind the
environmental restrictions discussed in Chapter 8
-- Product Specifications.
Step 4: ConnectyourPoESwitchtonetworkdevices.
A. Connect one end of a standard network cable to port-5
and port-6 10/100/1000Mbps RJ45 ports on the front of
thePoESwitchSwitch.
B.Connectthe otherendof the cabletothe network devices
such as NVR (Network Video Recorder), workstations or
routers.