User Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
Step 4: Connect your Gigabit Ethernet Switch to
network devices.
A. Connect one end of a standard network
cable to the 10/100/1000Mbps RJ45 ports
on the back of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations, routers, etc.
Note
Connection to the Gigabit Ethernet Switch
requires UTP Category 5 network cabling
with RJ45 tip.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable
to a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Wall-mount Installation
Step 1: Please nd the wall that can mount the
GSD-603F.
Step 2: Screw two screws on the wall.
1. Package Contents
Check the contents of your package for the following
parts:
Gigabit Ethernet Switch x 1 User's Manual x 1
AC Adapter x 1 Rubber Feet x 4
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
In the following sections, the term “Gigabit Ethernet
Switch” means the GSD-603F.
3. Hardware Introduction
3.1 Switch Front Panel
Figure 3-1 shows the front panel of GSD-603F.
Figure 3-1: GSD-603F Front Panel
3.2 Switch Rear Panel
Figure 3-2 shows the rear panel of GSD-603F.
12345
10/100/1000T
5V DC
SFP
1000X
Figure 3-2: GSD-603F Rear Panel
4. LED Indicators
System
LED Color Function
PWR
Green
Lights to indicate that the Switch
has power.
Per 10/100/1000BASE-T RJ45 Port (Port 1 ~ Port 5)
LED Color Function
LNK/ACT Green
Lights to indicate the link through
that port is successfully
established.
Blinks to indicate that the Switch
is actively sending or
receiving data over that
port.
1000BASE-X SFP Port
LED Color Function
LNK/ACT Green
Lights to indicate that the Switch
is successfully connecting to
the network at 1000Mbps.
2. Product Features
Physical
z Five 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
z One 1000BASE-X slot
Layer 2 Features
z Features Store-and-Forward mode with wire-speed
lteringandforwardingrates
z IEEE 802.3x, full-duplex ow control compliant; back-
pressure,half-duplexowcontrol
z Integrated address look-up engine, supporting 2K
absolute MAC addresses
z 1.5Mbit on-chip frame buffer
z 9K jumbo packet
z Power saving ability for Green networking
Hardware Features
z DC 5V, 1A external power
z Compact size, wall-mountable design
z Metal case, good for heat sinking
z Easy installation; ideal solution for space-limited
locations
Note
1. The device is a power-required device,
meaning it will not work till it is powered.
If your network remains to be active all
the time, please consider using UPS (Un-
interrupted Power Supply) for your de-
vice. It will prevent you from network
data loss or network downtime.
2. In some areas, installing a surge sup-
pression device may also help to protect
your Switch from being damaged by un-
regulated surge or current to the Switch
or the power adapter.
Step 3: Hang the GSD-603F on the screws from the
wall.
Step 4: Repeat Step 5 of Desktop Installation for
power supply to the GSD-603F.
Note
Before mounting the device to the wall,
please check the location of the electrical
outlet and the length of the Ethernet cable.
800 mm
GSD-603F Switch Bottom Side
12345
10/100/1000T
5V DC
SFP
1000X
RJ45
UTP Cable
5. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please read the
following topics and perform the procedures in the order
being presented.
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on desktop, simply
follow the steps below:
Step 1: Attach the rubber feet to the recessed areas
on the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on desktop
near an AC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.