User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the contents of your package for the following parts:
Gigabit Ethernet Switch x 1 AC Adapter x 1
User’s Manual x 1 Rubber Feet x 4
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.
In the following sections, the term “Gigabit Ethernet
Switch” means the GSD-603F.
3. Hardware Introduction
3.1 Switch Front Panel
Figure 3-1 shows the front panel of GSD-603F.
PWR SFP 1 2 3 4 5
ACT
LNK
GSD-603F
5-Port 10/100/1000T +1-Port 100/1000X SFP Gigabit Ethernet Switch
Figure 3-1: GSD-603F Front Panel
3.2 Switch Rear Panel
Figure 3-2 shows the rear panel of GSD-603F.
12345
10/100/1000T
5V , 1A max.
SFP
100/1000X
Figure 3-2: GSD-603F Rear Panel
Step 4: Connect your Gigabit Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100/1000Mbps RJ45 ports on the
back of the Gigabit Ethernet Switch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstations, routers, etc.
Note
Connection to the Gigabit Ethernet Switch
requires UTP Category 5 network cabling with
RJ45 tip.
Step 5: Supply power to the Gigabit Ethernet Switch.
A. Connect one end of the power cable to the
Gigabit Ethernet Switch.
B. Connect the power plug of the power cable to
a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the
Power LED should remain solid Green.
Wall-mount Installation
Step 1: PleasendthewallthatcanmounttheGSD-603F.
Step 2: Screw two screws on the wall.
Step 3: Hang the GSD-603F on the screws from the wall.
Step 4: Repeat Step 5 of Desktop Installation for power
supply to the GSD-603F.
4. LED Indicators
System
LED Color Function
PWR Green
Lights to indicate that the Switch has
power.
Per 10/100/1000BASE-T RJ45 Port (Port 1 ~ Port 5)
LED Color Function
LNK/
ACT
Green
Lights to indicate the link through that port
is successfully established.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
100/1000BASE-X SFP Port
LED Color Function
LNK/
ACT
Green
Lights to indicate that the Switch is
successfully connecting to the network at
100/1000Mbps.
2. Product Features
Physical
¾Five 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
¾One 100/1000BASE-X SFP Slot
Layer 2 Features
¾Features Store-and-Forward mode with wire-speed
lteringandforwardingrates
¾IEEE 802.3x, full-duplex ow control compliant; back-
pressure,half-duplexowcontrol
¾Integrated address look-up engine, supporting 2K abso-
lute MAC addresses
¾1.5Mbiton-chipframebuer
¾9K jumbo packet
¾Power saving ability for Green networking
Hardware Features
¾DC 5V, 1A external power
¾Compact size, wall-mountable design
¾Metal case, good for heat dissipation
¾Easy installation; ideal solution for space-limited locations
Power
Note
1. The device is a power-required device,
meaning it will not work till it is powered.
If your network remains to be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or
network downtime.
2. In some areas, installing a surge suppression
device may also help to protect your Switch
from being damaged by unregulated surge or
current to the Switch or the power adapter.
5. Installing the Switch
This part describes how to install your Gigabit Ethernet
Switch and make connections to it. Please read the
following topics and perform the procedures in the order
being presented.
Note
This Gigabit Ethernet Switch does not need
software configuration.
Desktop Installation
To install the Gigabit Ethernet Switch on desktop, simply
follow the steps below:
Step 1: Attach the rubber feet to the recessed areas on
the bottom of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on desktop near
an DC power source.
Step 3: Keep enough ventilation space between the
Gigabit Ethernet Switch and the surrounding
objects.
Note
Before mounting the device to the wall, please
check the location of the electrical outlet and
the length of the Ethernet cable.
800 mm
GSD-603F Switch Bottom Side
12345
10/100/1000T
5V DC
SFP
1000X
RJ45 UTP Cable