User's Manual
- 9 -
- 10 -
- 11 -
- 12 - - 13 -
Wall-mounted installation
Step 1: Find the wall that you want the GSD-504UP to be
mounted on.
Step 2: Please refer to the picture below and screw the two
screws into the marked areas of the wall.
122
Step 3: Hang the GSD-504UP on the screws from the wall.
Step 4: Repeat step 6 for the desktop Installation of the
power supply to the GSD-504UP.
Note
Before mounting the device to the wall, please
check the location of the electrical outlet and the
length of the Ethernet cable.
Power
Requirements
55V DC, 2.8A
Surge
Protection
Dierence Mode: ±4KV;
Common mode: ±6KV
ESD Protection Contact 4KV; air 6KV
Power
Consumption
Max. 136 watts, 464.05 BTU
Dimensions
(W x D x H)
168 x 93 x 32 mm
Weight 414g
Power over Ethernet
PoE Standard
IEEE 802.3at Power over Ethernet Plus/PSE
IEEE 802.3bt Power over Ethernet Plus Plus/
PSE
PoE Power
Supply Type
Port 1-2: End-span + Mid-span
Port 3-4: End-span
Power Pin
Assignment
Port 1-2: 4 pairs 1/2 (-), 3/6 (+) and
4/5 (+), 7/8 (-)
Port 3-4: 2 pairs 1/2 (-), 3/6 (+)
PoE Power
Output
Port 1-2: 90W max.;
Port 3-4: 30W max.
Total PoE
Power Budget
120 watts
8.ProductSpecications
Model
GSD-504UP
2-Port 10/100/1000T 802.3bt PoE + 2-Port
10/100/1000T 802.3at PoE + 1-Port Gigabit
Desktop Switch
Hardware Specications
Network
Connector
5 10/100/1000BASE-T RJ45 auto MDI/MDIX
ports
PoE Inject
Port
2 ports with 802.3bt PoE++ injector function
(Ports 1 to 2)
2 ports with 802.3af/at PoE+ injector
function (Ports 3 to 4)
LED Display
System: PWR (Orange)
Per PoE port: PoE (Orange, port 1 to port 4)
Ethernet port: LNK (Green)
Thermal Fan Fanless design
Switch
Architecture
Store and Forward
MAC Address
Table
2K MAC address table with auto learning
function
Switch Fabric 10Gbps
Switch
Throughput
7.44Mpps @64 bytes
Jumbo Packet 9K bytes
Flow Control
Back pressure for half duplex. IEEE 802.3x
pause frame for full duplex
Standard Conformance
EMI Safety FCC Part 15 Class A, CE
Standard
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Environment
Operating
Environment
0 ~ 50 degrees C
Storage
Environment
-10 ~ 70 degrees C
Operating
Humidity
5 ~ 95%, relative humidity, non-condensing
Storage
Humidity
5 ~ 95%, relative humidity, non-condensing
9. Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Website rst to check if it
could solve your issue. If you need more support information,
please contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq?method=category&c1=1
Support team mail address:
support@planet.com.tw
Copyright © PLANET Technology Corp. 2022
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
FCC Warning
This device has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
WEEE Warning
To avoid the potential eects on the environment and
human health as a result of the presence of
hazardous substances in electrical and electronic
equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.