User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Standard Mode (default)
Power
PoE IP Camera
PoE
100 meters (328 feet)
PoE
100BASE-TX UTP with PoE
GSD-2022P
Standard
VLAN
Extend
VLAN Isolation Mode
NVR
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
PoE
100BASE-TX UTP with PoE
GSD-2022P
IP Camera
IP Camera
IP Camera
Ports 17~18 and SFP Ports 19~20
to Ports 1~16 Access Permitted
1000BASE-T UTP
Standard
VLAN
Extend
Extend Mode
Ports 1 to 8
Power
250 meters (820 feet)
PoE
PoE
10BASE-T UTP with PoE
PoE IP Camera
GSD-2022P
Standard
VLAN
Extend
5. Hardware Installation
5.1 Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the
instructions described below.
Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with
the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+
Switch with supplied screws attached to the package. Figure
5-1 shows how to attach brackets to one side of the 802.3at
PoE+ Switch.
2 106 14 18 20
1 95 13 17 19
PoE Max
PWR
4 12
8 16
3 117 15
16-Port 10/100/1000T 802.3at PoE
+
2-Port
10/100/1000T
+
2-Port 1000X SFP Desktop Switch
19 20
1000X SFP
Standard
VLAN
Extend
PoE-in-Use
LNK
ACT
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
GSD-2022P
Figure 5-1: Attaching the Brackets to the 802.3at PoE+ Switch.
Caution
You must use the screws supplied with the mounting
brackets. Damage caused to the parts by using incorrect
screwswouldinvalidatethewarranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the
opposite side.
4.4 Rear Panel
The rear panel of the 802.3at PoE+ Switch indicates an AC power
socket,whichacceptsinputpowerfrom 100to240VAC,50-60Hz,5A.
50/60Hz
100-240V , 5A max.
Figure 4-2: GSD-2022P Switch Rear Panel
 AC Power Receptacle
Power
Notice
The device is a power-required device, which means
it will not work till it is powered. If your networks
should be active all the time, please consider using UPS
(Uninterrupted Power Supply) for your device. It will
preventyoufromnetworkdatalossornetworkdowntime.
Power
Notice
In some areas, installing a surge suppression device may
also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch,
use suitable screws to securely attach the brackets to the
rack, as shown in Figure 5-2.
2 106 14 18 20
1 95 13 17 19
PoE Max
PWR
4 12
8 16
3 117 15
16-Port 10/100/1000T 802.3at PoE
+
2-Port
10/100/1000T
+
2-Port 1000X SFP Desktop Switch
19 20
1000X SFP
Standard
VLAN
Extend
PoE-in-Use
LNK
ACT
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
GSD-2022P
Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack
Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at
compliedPDsandothernetworkdevices.
A. Connect one end of a standard network cable to the
10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at
PoE+ Switch.
B. Connecttheother end ofthecable tothenetwork devicessuchas
printerservers,workstationsorrouters,etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall
outlet.
When the 802.3at PoE+ Switch receives power, the power LED should
remain solid Green.
5.2 Installing the SFP Transceiver
The sections describe how to insert an SFP transceiver into an SFP slot
of the 802.3at PoE+ Switch.
TheSFPtransceiversarehot-pluggableandhot-swappable.You can plug
inandoutthetransceiverto/fromanySFPportwithout having topower
down the 802.3at PoE+ Switch, as the Figure 5-3 shows.
MGB-Series
SFP Transceiver
LC Fiber Cable
1
2
Figure 5-3: Plug In the SFP Transceiver
 Approved PLANET SFP Transceivers
PLANET 802.3at PoE+ Switch supports both single mode and multi-
mode SFP transceivers. The website link of approved PLANET SFP
transceiversisshownbelow:
https://www.planet.com.tw/en/product/mgb-series-transceiver
Note
It is recommended to use PLANET SFP on the 802.3at
PoE+ Switch. If you insert an SFP trans-ceiver that is not
supported,the802.3atPoE+Switchwillnotrecognizeit.
1. Before we connect the 802.3at PoE+ Switch to the other network
device, we have to make sure both sides of the SFP transceivers are
with the same media type, for example, 1000BASE-SX to 1000BASE-
SX; 1000BASE-LX to 1000BASE-LX.
2.Check whetherthe ber-opticcabletype matcheswith theSFP trans-
ceiverrequirement.
To connect to 1000BASE-SX SFP transceiver, please use the
multi-mode ber cable with one side being the male duplex LC
connector type.
To connect to 1000BASE-LX SFP transceiver, please use the
single-mode ber cable with one side being the male duplex LC
connector type.
Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET Web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address
[e-mail]
Copyright © PLANET Technology Corp. 2020
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.