User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Standard Mode (default)
Power
PoE IP Camera
PoE
100 meters (328 feet)
PoE
100BASE-TX UTP with PoE
GSD-2022P
Standard
VLAN
Extend
VLAN Isolation Mode
NVR
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
PoE
100BASE-TX UTP with PoE
GSD-2022P
IP Camera
IP Camera
IP Camera
Ports 17~18 and SFP Ports 19~20
to Ports 1~16 Access Permitted
1000BASE-T UTP
Standard
VLAN
Extend
Extend Mode
Ports 1 to 8
Power
250 meters (820 feet)
PoE
PoE
10BASE-T UTP with PoE
PoE IP Camera
GSD-2022P
Standard
VLAN
Extend
5. Hardware Installation
5.1 Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the
instructions described below.
Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with
the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+
Switch with supplied screws attached to the package. Figure
5-1 shows how to attach brackets to one side of the 802.3at
PoE+ Switch.
2 106 14 18 20
1 95 13 17 19
PoE Max
PWR
4 12
8 16
3 117 15
16-Port 10/100/1000T 802.3at PoE
+
2-Port
10/100/1000T
+
2-Port 1000X SFP Desktop Switch
19 20
1000X SFP
Standard
VLAN
Extend
PoE-in-Use
LNK
ACT
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
GSD-2022P
Figure 5-1: Attaching the Brackets to the 802.3at PoE+ Switch.
Caution
You must use the screws supplied with the mounting
brackets. Damage caused to the parts by using incorrect
screws would invalidate the warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the
opposite side.
4.4 Rear Panel
The rear panel of the 802.3at PoE+ Switch indicates an AC power
socket,whichacceptsinputpowerfrom 100to240VAC,50-60Hz,5A.
50/60Hz
100-240V , 5A max.
Figure 4-2: GSD-2022P Switch Rear Panel
 AC Power Receptacle
Power
Notice
The device is a power-required device, which means
it will not work till it is powered. If your networks
should be active all the time, please consider using UPS
(Uninterrupted Power Supply) for your device. It will
prevent you from network data loss or network downtime.
Power
Notice
In some areas, installing a surge suppression device may
also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch,
use suitable screws to securely attach the brackets to the
rack, as shown in Figure 5-2.
2 106 14 18 20
1 95 13 17 19
PoE Max
PWR
4 12
8 16
3 117 15
16-Port 10/100/1000T 802.3at PoE
+
2-Port
10/100/1000T
+
2-Port 1000X SFP Desktop Switch
19 20
1000X SFP
Standard
VLAN
Extend
PoE-in-Use
LNK
ACT
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
GSD-2022P
Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack
Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at
complied PDs and other network devices.
A. Connect one end of a standard network cable to the
10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at
PoE+ Switch.
B. Connect the other end of the cable to the network devices such as
printer servers, workstations or routers, etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall
outlet.
When the 802.3at PoE+ Switch receives power, the power LED should
remain solid Green.
5.2 Installing the SFP Transceiver
The sections describe how to insert an SFP transceiver into an SFP slot
of the 802.3at PoE+ Switch.
The SFP transceivers are hot-pluggable and hot-swappable. You can plug
in and out the transceiver to/from any SFP port without having to power
down the 802.3at PoE+ Switch, as the Figure 5-3 shows.
MGB-Series
SFP Transceiver
LC Fiber Cable
1
2
Figure 5-3: Plug In the SFP Transceiver
 Approved PLANET SFP Transceivers
PLANET 802.3at PoE+ Switch supports both single mode and multi-
mode SFP transceivers. The website link of approved PLANET SFP
transceivers is shown below:
https://www.planet.com.tw/en/product/mgb-series-transceiver
Note
It is recommended to use PLANET SFP on the 802.3at
PoE+ Switch. If you insert an SFP trans-ceiver that is not
supported,the802.3atPoE+Switchwillnotrecognizeit.
1. Before we connect the 802.3at PoE+ Switch to the other network
device, we have to make sure both sides of the SFP transceivers are
with the same media type, for example, 1000BASE-SX to 1000BASE-
SX; 1000BASE-LX to 1000BASE-LX.
2.Check whether the ber-opticcable typematches with the SFP trans-
ceiver requirement.
To connect to 1000BASE-SX SFP transceiver, please use the
multi-mode ber cable with one side being the male duplex LC
connector type.
To connect to 1000BASE-LX SFP transceiver, please use the
single-mode ber cable with one side being the male duplex LC
connector type.
Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET Web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address
[e-mail]
Copyright © PLANET Technology Corp. 2020
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.