L3 8-Port 10/100/1000T 802.
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 4 3. Terminal Setup............................................................................................ 5 3.1 Logging on to Console.......................................................................... 6 3.2 Configuring IP Address...............................
1. Package Contents Thank you for purchasing PLANET Managed PoE Switch, GS-5220-8P2T2X/GS5220-8UP2T2X. The descriptions of these models are shown below: GS-5220-8P2T2X L3 8-Port 10/100/1000T 802.3at PoE + 2-Port 10/100/1000T + 2-Port 10G SFP+ Managed Switch GS-5220-8UP2T2X L3 8-Port 10/100/1000T 802.3bt PoE + 2-Port 10/100/1000T + 2-Port 10G SFP+ Managed Switch “Managed PoE Switch” is used as an alternative name in this Quick Installation Guide.
2. Requirements zz Workstations running Windows XP/2003/2008/2012/Vista/7/8/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS232 converter. The above Workstations have been installed with terminal emulator, such as Tera Term, PuTTY or Hyper Terminal included in Windows XP/2003.
3. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial port of the Managed PoE Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port RJ45 Console Port Figure 3-1: Managed PoE Switch Console Connectivity A terminal program is required to make the software connection to the Managed PoE Switch. Putty or Tera Term may be a good choice. 1. Run terminal program on the OS. 2.
3.1 Logging on to Console Once the terminal is connected to the device, power on the Managed PoE Switch, and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 3-3 appears. Username: admin Password: admin Note The following console screen based on the GS-5220-8UP2T2X will be the same as that of the GS-5220-8P2T2X.
3.2 Configuring IP Address The Managed PoE Switch is shipped with default IP address shown below. IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows: Showing the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address as shown in Figure 3-4.
Configuring IP Address 3. At the “#” prompt, enter the following command and press as shown in Figure 3-5. GS-5220-8UP2T2X # configure terminal GS-5220-8UP2T2X (config)# interface vlan 1 GS-5220-8UP2T2X (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the Managed PoE Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Figure 3-5: Configuring IP Address Screen 4.
3.3 Storing Current Switch Configuration In the Managed PoE Switch, the running configuration sequence running-config can be saved from the RAM to FLASH by “copy” command, so that the running configuration sequence becomes the start-up configuration file, which is called configuration save. At the “#” prompt, enter the following command and press .
4. Starting Web Management The following shows how to start up the Web Management of the Managed PoE Switch. Note the Managed PoE Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Managed PoE Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Note The following web screen based on the GS-5220-8UP2T2X will be the same as that of the GS-5220-8P2T2X. 3. After entering the password, the main screen appears as Figure 4-3 shows. Figure 4-3: Web Main Screen of Managed PoE Switch The Switch Menu on the top of the Web page lets you access all the commands and statistics the Managed PoE Switch provides.
Figure 4-6: Switch Sub-menu Note If you are not familiar with Switch functions or the related parameter, press “Help icon” anytime on the Web page to get the help description. Now, you can use the Web management interface to continue the Switch management or manage the Switch by console interface. Please refer to the user’s manual for more. 4.2.
2. Press the “Save Configuration” button. 3. Or the other way to save the setting is to Click Maintenance, Save Startup Config.
5. Recovering Back to Default Configuration IP address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to default value, press the hardware-based reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. L3 8-Port 10/100/1000T 802.
6. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQs resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq Switch support team mail address: support@planet.com.tw GS-5220-8P2T2X/GS-5220-8UP2T2X User’s Manual: https://www.planet.com.
