GS-5220-Series (V4) User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 IGMP Snooping
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 Link OAM
- 4.4 Routing
- 4.5 Quality of Service
- 4.6 Security
- 4.7 Power over Ethernet
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-5220 PoE Series Managed Switch
36
GS-5220-24UP(L)4X(R) series
Product
GS-5220-24UP4X GS-5220-24UP4XR
GS-5220-24UPL4X
GS-5220-24UPL4XR
Hardware Specifications
Hardware Version
2
Copper Ports
24 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP/mini-GBIC Slots
4 100/1000BASE-X SFP interfaces, shared with Port-21 to Port-24
Compatible with 100BASE-FX SFP transceiver
SFP+ Slots
4 10GBASE-SR/LR SFP+ interfaces (Port-25 to Port-28)
Compatible with 1000BASE-SX/LX/BX SFP transceiver
Console
1 x RS232-to-RJ45 serial port (115200, 8, N, 1)
Switch Architecture
Store-and-Forward
Switch Fabric
128Gbps/non-blocking
Throughput
95.23Mpps@64Bytes
Address Table
16K entries, automatic source address learning and aging
Shared Data Buffer
32M bits
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Jumbo Frame
10K bytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
Dimensions (W x D x H)
440 x 300 x 44.5 mm, 1U height
Weight
4551g 4588g 5082g 5119g
Power Consumption
Max. 446.6
watts/1522.9 BTU
AC: Max. 446.6
watts/1522.9 BTU
DC: Max. 33.9
watts/115.5 BTU
Max. 659.9
watts/2249.2 BTU
AC: Max.659.9
watts/2249.2 BTU
DC: Max. 35.1
watts/119.7 BTU
Power Requirements – AC
AC 100~240V, 50/60Hz, 7A AC 100~240V, 50/60Hz, 10A
Power Requirements – DC
-- DC 36~60V, 2A -- DC 36~60V, 2A
ESD Protection
6KV DC
Fan
3 smart fans
Power over Ethernet
PoE Standard
IEEE 802.3af/802.3at/802.3bt Ultra PoE PSE
PoE Power Supply Type
End-span/Mid-span/UPoE
PoE Power Output
Per port 54V DC, 75 watts (max.) Per port 52V DC, 75 watts (max.)
Power Pin Assignment
End-span : 1/2(-), 3/6(+)
Mid-span : 4/5(+), 7/8(-)
UPoE : 1/2(-), 3/6(+),4/5(+), 7/8(-)
PoE Power Budget
400 watts (max.) 600 watts (max.)
PoE Ability PD @ 15 watts
24 units 24 units
PoE Ability PD @ 30 watts
13 units 20 units
PoE Ability PD @ 60 watts
6 units 10 units
Layer 2 Management Functions
Port Configuration
Port disable/enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable/enable