GS-5220-Series (V4) User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 IGMP Snooping
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 Link OAM
- 4.4 Routing
- 4.5 Quality of Service
- 4.6 Security
- 4.7 Power over Ethernet
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-5220 PoE Series Managed Switch
264
4.4.4.6 Area Range
This is OSPF area range configuration table. It is used to summarize the intra area paths from a specific address range in one
summary-LSA(Type-3) and advertised to other areas or configure the address range status as 'DoNotAdvertise' which the
summary-LSA(Type-3) is suppressed. The area range configuration is used for Area Border Routers (ABRs) and only
router-LSAs(Type-1) and network-LSAs (Type-2) can be summarized. The AS-external-LSAs(Type-5) cannot be summarized
because the scope is OSPF autonomous system (AS). The AS-external-LSAs(Type-7) cannot be summarized because the
feature is not supported yet.. The screen in Figure 4-4-4-6 appears.
Figure 4-4-4-6: Area Range Page Screenshot
The page includes the following fields:
Object Description
Area ID The OSPF area ID.
Network Address IPv4 network address.
Mask Length IPv4 network mask length.
Advertised When the value is true, it summarizes intra area paths from the address range in one
summary-LSA(Type-3) and advertised to other areas. Otherwise, the intra area paths from the
address range are not advertised to other areas.
Auto/Specific When 'Auto' is selected, the cost value is set to 0 automatically and isn't allowed to be configured.
Cost User specified cost (or metric) for this summary route. It is allowed to be configured only when
'Specific' is selected and the allowed range is 0 to 65535.. The allowed range is 1 to 16777215
and the default setting is 'auto cost' mode.
Buttons
Click to add new entry.
Click to save changes.
: Click to undo any changes made locally and revert to previously saved values.