GS-5220-Series (V4) User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 IGMP Snooping
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 Link OAM
- 4.4 Routing
- 4.5 Quality of Service
- 4.6 Security
- 4.7 Power over Ethernet
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of GS-5220 PoE Series Managed Switch
259
is advertised by the OSPF router.
Default Metric User specified default metric value for the OSPF routing protocol. The field is significant only when
the arugment 'IsSpecificDefMetric' is TRUE
Auto: The default metric is calculated automatically based on the routing protocols.
Specific: User specified default metric.
Static Redistribute
Metric Type
The OSPF redistributed metric type for the connected interfaces.
None: The static routes are not redistributed.
Specified Metric Value: User specified metric for the static routes.
External Type 1: External Type 1 of the static routes.
External Type 2: External Type 2 of the static routes.
Static Redistribute
Metric Value
User specified metric value for the connected interfaces. The field is significant only when the
arugment 'ConnectedRedistMetricType' is configured as 'metricTypeSpecified'.
The allowed range is 0 to 1677214.
Connected
Redistribute Metric
Type
The OSPF redistributed metric type for the static routes.
None: The connected interfaces are not redistributed.
Specified Metric Value: User specified metric for the connected interfaces routes.
External Type 1: External Type 1 of the connected interfaces routes.
External Type 2: External Type 2 of the connected interfaces routes.
Connected
Redistribute Metric
Value
User specified metric value for the static routes.The field is significant only when the arugment
'StaticRedistMetricType' is configured as 'metricTypeSpecified'.
The allowed range is 0 to 1677214.
Buttons
Click to reset the current OSPF process.
Click to save changes.
: Click to undo any changes made locally and revert to previously saved values.