User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 IGMP Snooping
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 Link OAM
- 4.4 Routing
- 4.5 Quality of Service
- 4.6 Security
- 4.7 Power over Ethernet
- 4.8 Ring
- 4.9 ONVIF
- 4.10 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
- EC Declaration of Conformity
User’s Manual of GS-5220 PoE Series Managed Switch
27
GS-5220-48P(L)4X(R) series
Product
GS-5220-48P4X GS-5220-48P4XR GS-5220-48PL4X GS-5220-48PL4XR
Hardware Specifications
Hardware Version
3
Copper Ports
48 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP+ Slots
4 10GBASE-SR/LR SFP+ interfaces (Port-25 to Port-28)
Compatible with 1000BASE-SX/LX/BX SFP transceiver
Console
1 x RS232-to-RJ45 serial port (115200, 8, N, 1)
Switch Architecture
Store-and-Forward
Switch Fabric
176Gbps/non-blocking
Throughput
130Mpps@64Bytes
Address Table
16K entries, automatic source address learning and aging
Shared Data Buffer
32M bits
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame
10K bytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
Dimensions (W x D x H)
440 x 300 x 44.5 mm, 1U height
Weight
4950g 4955g 5040g 5071g
Power Consumption
Max. 461 watts/1582
BTU
AC: Max. 461
watts/11582 BTU
DC: Max. 36.6
watts/124.88 BTU
Max.
680watts/2333 BTU
AC: Max.680
watts/2333 BTU
DC: Max.
36.6watts/124.88BTU
Power Requirements – AC
AC 100~240V, 50/60Hz, 7A AC 100~240V, 50/60Hz, 8A
Power Requirements – DC
-- DC 36~60V, 2A -- DC 36~60V, 2A
ESD Protection
6KV DC
Fan
3 smart fans
Power over Ethernet
PoE Standard
IEEE 802.3at PoE+ PSE
PoE Power Supply Type
End-span
PoE Power Output
36 watts (max.)
Power Pin Assignment
End-span : 1/2(-), 3/6(+)
PoE Power Budget
400 watts (max.) 600 watts (max.)
PoE Ability PD @ 7 watts
48 units 48 units
PoE Ability PD @ 15.4 watts
26 units 40 units
PoE Ability PD @ 30.8 watts
13 units 20 units
Layer 2 Management Functions
Port Configuration
Port disable/enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable/enable
Port Status
Display each port’s speed duplex mode, link status, flow control status,
auto-negotiation status, trunk status
Port Mirroring
TX/RX/Both
Many-to-1 monitor