User Guide

ManualsBrandsPLANET Technology ManualsStandard SwitchesL2+ 24-Port 100/1000X SFP + 8-Port Shared TP Managed Switch

Table Of Contents

Command Guide of GS-5220-16S8C and GS-5220-16S8CR

-1-

Summary of content (432 pages)

PAGE 1
Command Guide of GS-5220-16S8C and GS-5220-16S8CR -1-
PAGE 2
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Contents Chapter 1 COMMAND LINE INTERFACE......................................................... 20 1.1 Accessing the CLI ....................................................................................................... 20 1.2 Command Line Modes................................................................................................ 20 1.3 Requirements ...........................................................................................
PAGE 3
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.1.20 clear ip igmp snooping vlan ...............................................................................................................................36 4.1.21 clear ip statistics icmp icmp-msg .......................................................................................................................37 4.1.22 clear ip statistics icmp interface vlan .......................................................................................
PAGE 4
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.5 aaa authentication login http radius .....................................................................................................................54 4.2.6 aaa authentication login http tacacs ....................................................................................................................55 4.2.7 aaa authentication login ssh local.................................................................................................
PAGE 5
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.46 erps <1-64> rpl owner .......................................................................................................................................78 4.2.47 erps <1-64> sub ................................................................................................................................................78 4.2.48 erps <1-64> topology-change propagate.................................................................................
PAGE 6
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.22 evc l2cp peer(GG) ...............................................................................................................................105 4.2.65.23 evc update dei .....................................................................................................................................106 4.2.65.24 excessive-restart .................................................................................................................
PAGE 7
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.63 loop-protect tx-mode ...........................................................................................................................126 4.2.65.64 mac address-table learning .................................................................................................................127 4.2.65.65 media-type..................................................................................................................................
PAGE 8
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.104 qos storm unknown ...........................................................................................................................149 4.2.65.105 qos tag-remark ..................................................................................................................................150 4.2.65.106 qos tag-remark mapped .................................................................................................................
PAGE 9
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.66.6 ip address dhcp fallback ........................................................................................................................173 4.2.66.7 ip dhcp server........................................................................................................................................174 4.2.66.8 ip igmp snooping ...................................................................................................................
PAGE 10
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.12 host .....................................................................................................................................................196 4.2.73.13 lease....................................................................................................................................................197 4.2.73.14 netbios-name-server .................................................................................................
PAGE 11
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.97 ipv6 mld snooping............................................................................................................................................217 4.2.98 ipv6 mld snooping vlan ....................................................................................................................................218 4.2.99 ipv6 mld ssm-range ......................................................................................................
PAGE 12
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.124 mep aps ......................................................................................................................................240 4.2.125 mep cc ........................................................................................................................................240 4.2.126 mep client domain...............................................................................................
PAGE 13
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.165 no ..................................................................................................................................................................265 4.2.166 ntp .................................................................................................................................................................266 4.2.167 ntp server .........................................................................................
PAGE 14
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.200 rmon event ....................................................................................................................................................294 4.2.201 sflow agent-ip ................................................................................................................................................295 4.2.202 sflow collector-address ........................................................................................
PAGE 15
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.220 transport email to...........................................................................................................................................317 4.2.221 upnp ..............................................................................................................................................................317 4.2.222 upnp advertising-duration ....................................................................................
PAGE 16
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.12 exit............................................................................................................................ 334 4.12.1 exit...................................................................................................................................................................334 4.13 firmware................................................................................................................... 334 4.13.
PAGE 17
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.16 show green-ethernet......................................................................................................................................355 4.21.17 show green-ethernet energy-detect...............................................................................................................356 4.21.18 show green-ethernet short-reach......................................................................................................
PAGE 18
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.57 show ipv6 route .............................................................................................................................................384 4.21.58 show ipv6 statistics........................................................................................................................................385 4.21.59 show lacp ...........................................................................................................
PAGE 19
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.98 show switchport forbidden .............................................................................................................................420 4.21.99 show tacacs-server........................................................................................................................................421 4.21.100 show terminal ..............................................................................................................
PAGE 20
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Chapter 1 COMMAND LINE INTERFACE 1.1 Accessing the CLI When accessing the management interface for the switch over a direct connection to the server’s console port, or via a Telnet connection, the switch can be managed by entering command keywords and parameters at the prompt. Using the switch's command-line interface (CLI) is very similar to entering commands on a UNIX system. This chapter describes how to use the Command Line Interface (CLI). 1.
PAGE 21
Command Guide of GS-5220-16S8C and GS-5220-16S8CR The CLI provides the following modes:  User Mode When the operator logs into the CLI, the User Mode is the initial mode. The User Mode contains a limited set of commands. The command prompt shown at this level is: Command Prompt: switch>  Privileged Mode To have access to the full suite of commands, the operator must enter the Privileged Mode. The Privileged Mode requires password authentication.
PAGE 22
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Chapter 2 CONSOLE CLI MANAGEMENT 2.1 Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ-45 type of serial (console) port of the Managed Switch. Figure 2-1 Managed Switch Console Connectivity The console port of the Managed Switch is a RJ-45 type, RS-232 serial port connector. It is an interface for connecting a terminal directly.
PAGE 23
Command Guide of GS-5220-16S8C and GS-5220-16S8CR  Baud : 115200  Data bits :8  Parity : None  Stop bits :1  Flow control : None Figure 2-3 Hyper Terminal COM Port Configuration You can change these settings, if desired, after you log on. This management method is often preferred because you can remain connected and monitor the system during system reboots.
PAGE 24
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 2.2 Logon to the Console Once the terminal is connected to the device, power on the Managed Switch, and the terminal will display “running testing procedures”. Then, the following message asks to log-in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 3-1 appears.
PAGE 25
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address and Subnet Mask as shown in Figure 3-2. Figure 3-2: IP Information Screen  Configuring IP Address 3. At the “#” prompt, enter the following command and press . As shown in Figure 3-3. # configure terminal (config)# interface vlan 1 (config-if-vlan)# ip address 192.168.1.100 255.255.255.
PAGE 26
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.  Repeat step 1 to check if the IP address is changed. Store current switch configuration 5. At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 3-4: Saving Current Configuration Command Screen If the IP is successfully configured, the Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Managed Switch through the new IP address.
PAGE 27
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Chapter 3 TELNET CLI MANAGEMENT 3.1 Telnet Login The Managed Switch also supports telnet for remote management. The switch asks for user name and password for remote login when using telnet, please use “admin” for username & password. Default IP address: 192.168.0.
PAGE 28
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Chapter 4 Commands for CLI Configuration Before read the Command for CLI configuration, please refer to the table below and know what the main command type for which models is. Command Type Models PoE WGSW-48040HP / XGSW-28040HP 10G XGSW-28040HP / MGSW-28240F ERPS XGSW-28040HP / MGSW-28240F / MGSD-10080F MEP XGSW-28040HP / MGSW-28240F / MGSD-10080F EVC None GVRP None sflow None Link OAM None 4.1 clear 4.1.
PAGE 29
Command Guide of GS-5220-16S8C and GS-5220-16S8CR clear access-list ace statistics Default: N/A Usage Guide: To clear the Access list entry statistics. Example: To clear the Switch’s Access list entry statistics. Switch# clear access-list ace statistics 4.1.3 clear dot1x statistics interface Command: clear dot1x statistics interface GigabitEthernet | 10GigabitEthernet Default: N/A Usage Guide: To clear the dot1x statistics. Example: To clear the Switch’s GigabitEthernet 1/25 dot1x statistics.
PAGE 30
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To clear the EPS instance number. 4.1.5 clear erps Command: clear erps < ERPS group numbers > statistics Default: N/A Usage Guide: To clear the ERPS group numbers statistics. Example: To clear the Switch’s ERPS group 1 statistics. Switch# # clear erps 1 statistics 4.1.6 clear erps statistics Command: clear erps statistics Default: N/A Usage Guide: To clear the ERPS statistics. Example: To clear the Switch’s ERPS statistics.
PAGE 31
Command Guide of GS-5220-16S8C and GS-5220-16S8CR clear evc statistics Default: N/A Usage Guide: To clear the Ethernet Virtual Connections statistics. Example: To clear the Switch’s Ethernet Virtual Connections statistics. Switch# clear evc statistics 4.1.8 clear ip arp Command: clear ip arp Default: N/A Usage Guide: To clear the ARP cache. Example: To clear the Switch’s ARP cache. Switch# clear ip arp 4.1.
PAGE 32
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To clear the Switch’s DHCP detailed statistics for all. Switch# clear ip dhcp detailed statistics all 4.1.10 clear ip dhcp detailed statistics client Command: clear ip dhcp detailed statistics client Default: N/A Usage Guide: To clear the DHCP client statistics. Example: To clear the Switch’s DHCP client statistics. Switch# clear ip dhcp detailed statistics client 4.1.
PAGE 33
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To clear the Switch’s DHCP normal L2 or L3 forward statistics. Switch# clear ip dhcp detailed statistics helper 4.1.12 clear ip dhcp detailed statistics server Command: clear ip dhcp detailed statistics server Default: N/A Usage Guide: To clear the DHCP server statistics. Example: To clear the Switch’s DHCP server statistics. Switch# clear ip dhcp detailed statistics server 4.1.
PAGE 34
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To clear the Switch’s DHCP normal L2 or L3 forward statistics. Switch# clear ip dhcp detailed statistics snooping 4.1.14 clear ip dhcp relay statistics Command: clear ip dhcp relay statistics Default: N/A Usage Guide: To clear the DHCP relay statistics. Example: To clear the Switch’s DHCP relay statistics. Switch# clear ip dhcp relay statistics 4.1.15 clear ip dhcp server binding Command: clear ip dhcp server binding A.B.C.
PAGE 35
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To clear the DHCP server binding cache. Example: To clear the Switch’s DHCP server(192.168.0.100) binding cache. Switch# clear ip dhcp server binding 192.168.0.100 4.1.16 clear ip dhcp server binding automatic Command: clear ip dhcp server binding automatic Default: N/A Usage Guide: To clear the DHCP automatic bindings cache. Example: To clear the Switch’s DHCP automatic bindings cache. Switch# clear ip dhcp server binding automatic 4.1.
PAGE 36
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: clear ip dhcp server binding manual Default: N/A Usage Guide: To clear the DHCP server manual binding cache. Example: To clear the Switch’s DHCP server manual binding cache. Switch# clear ip dhcp server binding manual 4.1.19 clear ip igmp snooping statistics Command: clear ip igmp snooping statistics Default: N/A Usage Guide: To clear the IGMP snooping statistics. Example: To clear the Switch’s IGMP snooping statistics.
PAGE 37
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To clear the IGMP snooping vlan < vlan_list> statistics. Example: To clear the Switch’s IGMP snooping vlan 1 statistics. Switch# clear ip igmp snooping vlan 1 statistics 4.1.21 clear ip statistics icmp icmp-msg Command: clear ip statistics icmp icmp-msg ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv4 ICMP traffic for designated message type.
PAGE 38
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To clear the IPv4 interface/ICMP statistics for specific VLAN. Example: To clear the Switch’s IP interface/ICMP statistics for specific VLAN 1. Switch# clear ip statistics icmp interface vlan 1 4.1.
PAGE 39
Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To clear the IPv4 ICMP interface statistics for specific VLAN. Example: To clear the Switch’s IPv4 ICMP interface statistics for specific VLAN 1. Switch# clear ip statistics system icmp interface vlan 1 4.1.25 clear ipv6 mld snooping statistics Command: clear ipv6 mld snooping statistics Default: N/A Usage Guide: To clear the ipv6 mld snooping statistics. Example: To clear the Switch’s ipv6 mld snooping statistics.
PAGE 40
Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To clear the ipv6 mld snooping statistics for specific VLAN. Example: To clear the Switch’s ipv6 mld snooping statistics for specific VLAN 1. Switch# clear ipv6 mld snooping vlan 1 statistics 4.1.27 clear ipv6 neighbors Command: clear ipv6 neighbors Default: N/A Usage Guide: To clear the ipv6 neighbors. Example: To clear the Switch’s ipv6 neighbors. Switch# clear ipv6 neighbors 4.1.
PAGE 41
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To clear the IPv6 ICMP traffic for designated message type. Example: To clear the Switch’s IPv6 ICMP traffic for designated message type 0. Switch# clear ipv6 statistics icmp icmp-msg 0 4.1.29 clear ipv6 statistics icmp interface vlan Command: clear ipv6 statistics icmp interface vlan VLAN identifier(s): VID Default: N/A Usage Guide: To clear the IPv6 interface/ICMP statistics for specific VLAN.
PAGE 42
Command Guide of GS-5220-16S8C and GS-5220-16S8CR ICMP message type ranges from 0 to 255 Default: N/A Usage Guide: To clear the IPv6 ICMP statistics for specific ICMP message type. Example: To clear the Switch’s IPv6 ICMP statistics for specific ICMP message type 0. Switch# clear ipv6 statistics system icmp icmp-msg 0 4.1.
PAGE 43
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To clear the lacp statistics. Example: To clear the Switch’s lacp statistics. Switch# clear lacp statistics 4.1.33 clear lldp statistics Command: clear lldp statistics Default: N/A Usage Guide: To clear the lldp statistics. Example: To clear the Switch’s lldp statistics. Switch# clear lldp statistics 4.1.
PAGE 44
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To clear the logging error info. Example: To clear the Switch’s logging error info. Switch# clear logging error info 4.1.35 clear logging error warning Command: clear logging error warning Default: N/A Usage Guide: To clear the logging error warning. Example: To clear the Switch’s logging error warning. Switch# clear logging error warning 4.1.
PAGE 45
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To clear the logging info error. Example: To clear the Switch’s logging info error. Switch# clear logging info error 4.1.37 clear logging info warning Command: clear logging info warning Default: N/A Usage Guide: To clear the logging info warning. Example: To clear the Switch’s logging info warning. Switch# clear logging info warning 4.1.
PAGE 46
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.1.39 clear logging warning info Command: clear logging warning info Default: N/A Usage Guide: To clear the logging warning info. Example: To clear the Switch’s logging warning info. Switch# clear logging warning info 4.1.40 clear mac address-table Command: clear mac address-table Default: N/A Usage Guide: To clear the mac address-table. Example: To clear the Switch’s mac address-table. Switch# clear mac address-table 4.1.
PAGE 47
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To clear the MEP instance profiles. 4.1.42 clear mvr name Command: clear mvr name MVR multicast VLAN name Default: N/A Usage Guide: To clear the mvr name profiles. 4.1.43 clear mvr statistics Command: clear mvr statistics Default: N/A Usage Guide: To clear the mvr statistics. Example: To clear the Switch’s mvr statistics. Switch# clear mvr statistics 4.1.
PAGE 48
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To clear the mvr vlan statistics for specific VLAN. Example: To clear the Switch’s mvr vlan statistics for specific VLAN 1. Switch# clear mvr vlan 1 statistics 4.1.45 clear network-clock clk-source Command: clear network-clock clk-source Clock source number Default: N/A Usage Guide: To clear the ERPS WTR timer for a specific profile. Example: To clear the Switch’s ERPS WTR timer for a specific profile 1.
PAGE 49
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.1.47 clear spanning-tree detected-protocols interface * Command: clear spanning-tree detected-protocols interface * Default: N/A Usage Guide: To clear the spanning-tree detected-protocols for all. Example: To clear the Switch’s spanning-tree detected-protocols for all. Switch# clear spanning-tree detected-protocols interface * 4.1.
PAGE 50
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.1.49 clear spanning-tree detected-protocols interface 10GigabitEthernet Command: clear spanning-tree detected-protocols interface 10GigabitEthernet Port list in X/X-XX Default: N/A Usage Guide: To clear the spanning-tree detected-protocols for specific 10GigabitEthernet port. Example: To clear the Switch’s spanning-tree detected-protocols for specific 10GigabitEthernet 1/1.
PAGE 51
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To clear the spanning-tree statistics for specific GigabitEthernet port. Example: To clear the Switch’s spanning-tree statistics for specific GigabitEthernet 1/1. Switch# clear spanning-tree statistics interface GigabitEthernet 1/1 4.1.
PAGE 52
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To clear the Switch’s statistics for all. Switch# clear statistics * 4.1.54 clear statistics GigabitEthernet Command: clear statistics GigabitEthernet Port list in X/X-XX Default: N/A Usage Guide: To clear the statistics for specific GigabitEthernet port. Example: To clear the Switch’s statistics for specific GigabitEthernet 1/1. Switch# clear statistics GigabitEthernet 1/1 4.1.
PAGE 53
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2 configure terminal 4.2.1 aaa authentication login console local Command: aaa authentication login console local Default: console : local Usage Guide: To authenticate the local account via console only. Example: To authenticate the local account via console. Switch# configure terminal Switch (config)# aaa authentication login console local 4.2.
PAGE 54
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: aaa authentication login console tacacs Default: console : local Usage Guide: To authenticate the tacacs account via console only. Example: To authenticate the local and radius and tacacs account via console. Switch# configure terminal Switch (config)# aaa authentication login console local radius tacacs 4.2.
PAGE 55
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To authenticate the radius account via http only. Example: To authenticate the local and radius account via http. Switch# configure terminal Switch (config)# aaa authentication login http local radius 4.2.6 aaa authentication login http tacacs Command: aaa authentication login http tacacs Default: http : local Usage Guide: To authenticate the tacacs account via http only.
PAGE 56
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# aaa authentication login ssh local 4.2.8 aaa authentication login ssh radius Command: aaa authentication login ssh radius Default: ssh : local Usage Guide: To authenticate the radius account via ssh only. Example: To authenticate the local and radius account via ssh. Switch# configure terminal Switch (config)# aaa authentication login ssh local radius 4.2.
PAGE 57
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.10 aaa authentication login telnet local Command: aaa authentication login telnet local Default: telnet : local Usage Guide: To authenticate the local account via telnet only. Example: To authenticate the local account via telnet. Switch# configure terminal Switch (config)# aaa authentication login telnet local 4.2.
PAGE 58
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.12 aaa authentication login telnet tacacs Command: aaa authentication login telnet tacacs Default: telnet : local Usage Guide: To authenticate the tacacs account via telnet only. Example: To authenticate the local and radius and tacacs account via telnet. Switch# configure terminal Switch (config)# aaa authentication login telnet local radius tacacs 4.2.
PAGE 59
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To enable the access management profile to allow SNMP / Telnet / HTTP services. Example: To create a Profile 1 enabling all services for VLAN 1 (IPv6 address 2001::7788) . Switch# configure terminal Switch (config)# access management 1 1 2001::7788 all 4.2.
PAGE 60
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To create and set up a profile for the access list. Example: To set a Profile 1 up (action: permit, dmac-type: unicast, frametype: ipv4-icmp, ingress: any, logging: disable, policy: 1, rate-limiter: 1, tag-priority: 1. vid: 1). Switch# configure terminal Switch (config)# access-list ace 1 action permit dmac-type unicast frametype ipv4-icmp ingress any logging disable policy 1 rate-limiter 1 tag-priority 1 vid 1 4.2.
PAGE 61
Command Guide of GS-5220-16S8C and GS-5220-16S8CR tag-priority Tag priority vid VID field Default: N/A Usage Guide: To update the specific profile for the access list. Example: Original: Profile 1 (action: permit, dmac-type: unicast, frametype: ipv4-icmp, ingress: any, logging: disable, policy: 1, rate-limiter: 1, tag-priority: 1. vid: 1). Updated: Profile 1 (action: deny, dmac-type: any, frametype: ipv4-icmp, ingress: any, logging: disable, policy: 1, rate-limiter: 1, tag-priority: 1. vid: 1).
PAGE 62
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.17 access-list rate-limiter pps Command: access-list rate-limiter pps Rate value Default: 0 Usage Guide: To set pps rate for all rate-limiter ID. Example: To set pps rate(10000 pps) for all rate-limiter ID. Switch# configure terminal Switch (config)# access-list rate-limiter pps 100 4.2.
PAGE 63
Command Guide of GS-5220-16S8C and GS-5220-16S8CR distribution only. Switch# configure terminal Switch (config)# access-list rate-limiter pps 100 4.2.
PAGE 64
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure banner-text. Example: To configure banner-text with word “ddddd”. Switch# configure terminal Switch (config)# banner 1 Enter TEXT message. End with the character '1'. ddddd 1 Telnet 192.168.0.100 ddddd Username: 4.2.21 banner exec Command: banner login c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure login banner-text.
PAGE 65
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Telnet 192.168.0.100: Username: admin Password: gggggg # 4.2.22 banner login Command: banner login c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure login banner-text. Example: To configure login banner-text with word “wwwwwwwwww”. Switch# configure terminal Switch (config)# banner login 1 Enter TEXT message. End with the character '1'.
PAGE 66
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.23 banner motd Command: banner motd c banner-text c, where 'c' is a delimiting character Default: N/A Usage Guide: To configure motd banner-text. Example: To configure motd banner-text with word “ffffff”. Switch# configure terminal Switch (config)# banner motd 1 Enter TEXT message. End with the character '1'. ffffff 1 Console: ffffff Press ENTER to get started Username: 4.2.
PAGE 67
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To set daylight saving. Example: To set daylight saving (Started time: Feb, 3. 2013 8:8AM, End time: Dec, 31. 2013 8:8AM, Offset time: 60 minutes). Switch# configure terminal Switch (config)# clock summer-time 1 date 2 3 2013 8:8 12 31 2013 8:8 60 4.2.25 clock timezone Command: clock timezone name of time zone Default: 0 Usage Guide: To set timezone. Example: To set timezone (GMT -15) with profile 1.
PAGE 68
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# default access-list rate-limiter 1 4.2.27 dot1x authentication timer inactivity Command: dot1x authentication timer inactivity <10-1000000> Default: Aging period: 300 Usage Guide: To set the Aging period for Network Access Server. Example: To set the Aging period (147 seconds). Switch# configure terminal Switch (config)# dot1x authentication timer inactivity 147 4.2.
PAGE 69
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.29 dot1x feature Command: dot1x feature guest-vlan | radius-qos | radius-vlan Default: Disable Usage Guide: To enable the guest-vlan, radius-qos, radius-vlan for Network Access Server Example: To enable the guest-vlan, radius-qos, radius-vlan for Network Access Server. Switch# configure terminal Switch (config)# dot1x authentication timer re-authenticate 777 4.2.
PAGE 70
Command Guide of GS-5220-16S8C and GS-5220-16S8CR dot1x guest-vlan supplicant supplicant The switch remembers if an EAPOL frame has been received on the port for the life-time of the port. Once the switch considers whether to enter the Guest VLAN, it will first check if this option is enabled or disabled.
PAGE 71
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disable Usage Guide: To enable 802.1X service for Network Access Server Example: To enable 802.1X service for Network Access Server Switch# configure terminal Switch (config)# dot1x system-auth-control 4.2.34 dot1x timeout quiet-period Command: dot1x timeout quiet-period <10-1000000> quiet-period Time in seconds before a MAC-address that failed authentication gets a new authentication chance. Default: 10 Usage Guide: To configure 802.
PAGE 72
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure 802.1X EPOAL timeout (45 seconds) for Network Access Server Switch# configure terminal Switch (config)# dot1x timeout tx-period 45 4.2.36 enable password Command: enable password The UNENCRYPTED (cleartext) password.
PAGE 73
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disable Usage Guide: To configure enable password and specific level for user Example: To configure enable password(admin) and specific level(15) for user Switch# configure terminal Switch (config)# enable password level 15 admin Press ENTER to get started Username: Password: > enable Password: admin # 4.2.
PAGE 74
Command Guide of GS-5220-16S8C and GS-5220-16S8CR enable secret 5 level 15 FC89368B9513DE0760290BCE9A1DA90A …………… Press ENTER to get started Username: Password: > enable Password: cisco # 4.2.39 end Command: end Default: N/A Usage Guide: To level the configure terminal mode Example: To level the configure terminal mode Switch# configure terminal Switch (config)# end # 4.2.
PAGE 75
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: erps <1-64> guard <10-2000> <1-64> ERPS group number <10-2000> Guard time in ms Default: 500 Usage Guide: To configure the Guard Time for ERPS. Example: To configure the Guard Time(178 ms) for ERPS(Profile 1) Switch# configure terminal Switch (config)# erps 1 guard 178 4.2.
PAGE 76
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: erps <1-64> major port0 interface {10GigabitEthernet, GigabitEthernet} port1 interface {10GigabitEthernet, GigabitEthernet} [ interconnect ] <1-64> ERPS group number interconnect Major ring is interconnected Default: 0 Usage Guide: To create a profile and configure the Major ERPS interface port 0, port 1.
PAGE 77
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# erps 1 mep port0 sf 2 aps 1 port1 sf 4 aps 3 4.2.44 erps <1-64> mep Command: erps <1-64> revertive <1-64> ERPS group number Wait-to-restore time in minutes Default: 0 Usage Guide: To configure WTR time for specific ERPS profile. Example: To configure WTR time(5 minuites) for specific ERPS profile 1. Switch# configure terminal Switch (config)# erps 1 revertive 5 4.2.
PAGE 78
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.46 erps <1-64> rpl owner Command: erps <1-64> rpl owner { port0 | port1 } port0 ERPS Port 0 interface port1 ERPS Port 1 interface Default: N/A Usage Guide: To configure Ring Protection Link Owner Role for specific ERPS interface. Example: To configure Ring Protection Link Owner Role for specific ERPS interface.. Switch# configure terminal Switch (config)# erps 1 rpl owner port0 4.2.
PAGE 79
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# erps 3 sub port0 interface GigabitEthernet 1/5 port1 interface GigabitEthernet 1/6 Example 2: To create a profile 2 and configure the Sub ERPS interface port 0(GigabitEthernet 1/3), port 1(GigabitEthernet 1/4) with interconnected mode and Major RIng group 1 and virtual-channel Switch# configure terminal Switch (config)# erps 1 sub port0 interface GigabitEthernet 1/3 interconnect 1 virtual-channel 4.2.
PAGE 80
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: V2 Usage Guide: To configure ERPS version number for the specific profile. Example: To configure ERPS version 1 for the specific profile 1. Switch# configure terminal Switch (config)# erps 1 version 1 4.2.
PAGE 81
Command Guide of GS-5220-16S8C and GS-5220-16S8CR vid EVC identifier Setup EVC VLAN ID ivid EVC VLAN ID Setup internal EVC VLAN ID Internal VLAN ID interface Setup NNI learning Setup learning policer Policer (ingress bandwidth profile) discard none Policer ID List of VLANs Map to policer discarding all frames Map to policer allowing all frames Default: 0 Usage Guide: To configure Ethernet Virtual Circuits
PAGE 82
Command Guide of GS-5220-16S8C and GS-5220-16S8CR direction ECE idenfifier Setup ECE direction both Bidirectional traffic flow nni-to-uni NNI-to-UNI traffic flow uni-to-nni UNI-to-NNI traffic flow evc EVC mapping EVC identifier none Map to no EVC ID frame-type Setup matched frame type any Match any frame type ipv4 Match IPv4 frames ipv6 Match IPv6 frames inner-tag Setup inner tag options add Setup inner tag add properties.
PAGE 83
Command Guide of GS-5220-16S8C and GS-5220-16S8CR s-tagged Match S-tagged frames tagged Match tagged frames untagged Match untagged frames vid Setup matched VLAN ID Matched VLAN ID value/range any interface next Match any VLAN ID Setup UNI Setup the ECE ID of the next entry Select ECE ID of an existing entry last Make the ECE the last entry outer-tag add Setup outer tag options Setup outer tag add properties dei Setup added tag DEI mode A
PAGE 84
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure EVC Control Entry as tabled below. Switch# configure terminal Switch (config)# evc ece 1 direction both evc 2 frame-type ipv4 inner-tag add dei 1 pcp 4 preserve type s-custom-tag vid 5 interface GigabitEthernet 1/3 outer-tag add dei 0 mode enable pcp 2 vid 7 match dei any pcp any type c-tagged vid 6 policer 8 policy 9 pop 2 4.2.
PAGE 85
Command Guide of GS-5220-16S8C and GS-5220-16S8CR [ | any] } policer { | discard | evc | none} policy pop direction ECE identifier Setup ECE direction both Bidirectional traffic flow nni-to-uni NNI-to-UNI traffic flow uni-to-nni UNI-to-NNI traffic flow evc EVC mapping EVC identifier none Map to no EVC ID frame-type Setup matched frame type any Match any frame type ipv4 Match IPv4 frames ip
PAGE 86
Command Guide of GS-5220-16S8C and GS-5220-16S8CR any Match tagged and untagged frames c-tagged Match C-tagged frames s-tagged Match S-tagged frames tagged Match tagged frames untagged Match untagged frames vid Setup matched VLAN ID Matched VLAN ID value/range any interface next Match any VLAN ID Setup UNI Setup the ECE ID of the next entry Select ECE ID of an existing entry last Make the ECE the last entry outer-tag add Setup outer tag options Setup
PAGE 87
Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To update EVC Control Entry for specific ECE profile. Example 1: To update “direction nni-to-uni” for ECE profile 1. Switch# configure terminal Switch (config)# evc ece 1 direction nni-to-uni 4.2.
PAGE 88
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure a profile for EVC Policer (Ingress Bandwidth Profile) . Example: To configure EVC Policer (Ingress Bandwidth Profile) as tabled below. Switch# configure terminal Switch (config)# evc policer 1 enable cbs 20 cir 30 ebs 40 eir 50 mode aware rate-type data type mef 4.2.
PAGE 89
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To update a profile for EVC Policer (Ingress Bandwidth Profile). Example: To update EVC Policer (Ingress Bandwidth Profile) with EIR 1000 for policer 1 Switch# configure terminal Switch (config)# evc policer update 1 eir 1000 4.2.
PAGE 90
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.57 exit Command: exit Default: N/A Usage Guide: To exit configure terminal mode. Example: To exit configure terminal mode. Switch# configure terminal Switch (config)# exit # 4.2.58 green-ethernet led interval Command: green-ethernet led interval <0~24> intensity <0-100> <0~24> Interval from 00.00 to 24.00 (00 is used to start at midnight, while 24 is used to stop at midnight). intensity <0-100> LEDs intensity.
PAGE 91
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# green-ethernet led interval 8-13 intensity 80 4.2.59 green-ethernet led on-event Command: green-ethernet led on-event error | link-change <0-65535> error Set LEDs intensity to 100% if an error occurs. link-change Specifies how long to turn LEDs intensity into 100%, when a link changes state. <0-65535> Number of seconds to set LEDs intensity at 100% at link change.
PAGE 92
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To enable GVRP. Switch# configure terminal Switch (config)# gvrp 4.2.61 gvrp max-vlans Command: gvrp max-vlans <1-4095> Default: 20 Usage Guide: To configure how many VLANs will be in GVRP. Example: To configure 200 VLANs in GVRP. Switch# configure terminal Switch (config)# gvrp max-vlans 200 4.2.
PAGE 93
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure Join-time, Leave-time, Leave all-time for GVRP. Example: To configure Join-time, Leave-time, Leave all-time for GVRP as tabled below. Switch# configure terminal Switch (config)# gvrp time join-time 5 leave-all-time 1200 leave-time 150 4.2.63 help Command: help Default: N/A Usage Guide: To explain how to use commands. Example: To explain how to use commands.
PAGE 94
Command Guide of GS-5220-16S8C and GS-5220-16S8CR (e.g. 'show pr?'.) 4.2.64 hostname Command: hostname < WORD > < WORD > This system's network name Default: N/A Usage Guide: To configure switch’s hostname. Example: To configure switch’s hostname with “planetbestswitch” Switch# configure terminal Switch (config)# hostname planetbestswitch planetbestswitch(config)# 4.2.
PAGE 95
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# interface 10GigabitEthernet 1/2 Switch (config-if) # 4.2.65.1 access-list action permit Command: access-list action permit action Access list action Default: Permit Usage Guide: To configure Permit for the ACL action. Example: To configure Permit ACL action for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list action permit 4.2.65.
PAGE 96
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.3 access-list logging Command: access-list logging logging Logging frame information. Note: The logging feature only works when the packet length is less than 1518 (without VLAN tags) and the System Log memory size and logging rate is limited. Default: Disable Usage Guide: To enable Logging function for the ACL. Example: To enable ACL Logging function for the GigabitEthernet X/X.
PAGE 97
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.5 access-list port-state Command: access-list port-state port-state Re-enable shutdown port that was shutdown by access-list module Default: Enable Usage Guide: To enable Port-state function for the ACL. Example: To configure ACL Port-state function for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # access-list port-state 4.2.65.
PAGE 98
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.7 access-list redirect interface Command: access-list redirect interface 10GigabitEthernet | GigabitEthernet redirect Redirect frame to specific port Default: Disable Usage Guide: To redirect frames to specific Port. Example: To redirect GigabitEthernet X/X frames to GigabitEthernet 1/2.
PAGE 99
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.9 aggregation group Command: aggregation group aggregation Create an aggregation group Create an aggregation group The aggregation group id Default: N/A Usage Guide: To configure aggregation group. Example: To configure aggregation group 7 for the GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # aggregation group 7 4.2.65.
PAGE 100
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.11 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands in configure terminal mode Example: To run “show aaa” in configure terminal mode. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # do show aaa console : local telnet ssh http : local : local : local 4.2.65.
PAGE 101
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.13 dot1x port-control Command: dot1x port-control auto | force-authorized | force-unauthorized | mac-based | multi | single dot1x IEEE Standard for port-based Network Access Control port-control Sets the port security state. auto Port-based 802.1X Authentication force-authorized Port access is allowed force-unauthorized Port access is not allowed mac-based Switch authenticates on behalf of the client multi Multiple Host 802.
PAGE 102
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To enable RADIUS-assigned QoS for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x radius-qos 4.2.65.15 dot1x radius-vlan Command: dot1x radius-vlan dot1x IEEE Standard for port-based Network Access Control radius-vlan Enables/disables per-port state of RADIUS-assigned VLAN. Default: Disable Usage Guide: To enable RADIUS-assigned VLAN for 802.
PAGE 103
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To restart 802.1X authentication process for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # dot1x re-authenticate 4.2.65.17 duplex Command: duplex auto | full | half duplex Interface duplex auto Auto negotiation of duplex mode. full Forced full duplex. half Forced half duplex. Default: Auto Usage Guide: To configure duplex mode for interface.
PAGE 104
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # end Switch# 4.2.65.19 evc dei Command: evc dei colored | fixed evc Ethernet Virtual Connections dei Setup DEI mode colored Allow policer to set DEI fixed Use classified DEI Default: Fixed Usage Guide: To configure EVC DEI mode Example: To configure EVC DEI mode (Colored) for GigabitEthernet X/X.
PAGE 105
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Select BPDU addresses (0-15) and GARP addresses (16-31) Default: N/A Usage Guide: To configure policy ID of L2CP discard Example: To configure policy ID 1 of L2CP discard for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc l2cp discard 1 4.2.65.
PAGE 106
Command Guide of GS-5220-16S8C and GS-5220-16S8CR evc l2cp forward evc Ethernet Virtual Connections l2cp Setup L2CP forwarding peer Redirect L2CP frames to local protocol entity Select BPDU addresses (0-15) and GARP addresses (16-31) Default: N/A Usage Guide: To configure policy ID of L2CP peer Example: To configure policy 1 of L2CP peer for GigabitEthernet X/X.
PAGE 107
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# interface GigabitEthernet X/X Switch (config-if) # evc update dei colored 4.2.65.24 excessive-restart Command: excessive-restart excessive-restart Restart backoff algorithm after 16 collisions (No excessive-restart means discard frame after 16 collisions) Default: Discard Usage Guide: To enable Backoff Algorithm for the specific interface Example: To enable Backoff Algorithm for the GigabitEthernet X/X.
PAGE 108
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.26 flowcontrol Command: flowcontrol off | on flowcontrol Traffic flow control. off Disable flow control. on Enable flow control. Default: Disable Usage Guide: To enable Flow-control for specific interface Example: To enable Flow-control for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # flowcontrol on 4.2.65.
PAGE 109
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.28 green-ethernet short-reach(GG) Command: green-ethernet short-reach green-ethernet short-reach Green ethernet (Power reduction) Enable power saving for ports which is connect to link partner with short cable.
PAGE 110
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.30 gvrp leave-request vlan(GG) Command: gvrp leave-request vlan gvrp Enable GVRP on port(s) leave-request Emit a Leave-Request for test purpose Default: N/A Usage Guide: To send GVRP Leave-Request to specific interface Example: To send GVRP Leave-Request(VLAN 1) to GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # gvrp leave-request vlan 1 4.2.65.
PAGE 111
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-if) # ip arp inspection check-vlan 4.2.65.
PAGE 112
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure Trusted into ARP inspection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip arp inspection trust 4.2.65.
PAGE 113
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip igmp snooping filter 1 4.2.65.
PAGE 114
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.
PAGE 115
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.40 ip verify source limit Command: ip verify source limit <0-2> <0-2> the number of limit Default: Unlimited Usage Guide: To limit numbers of Dynamic Client for specific interface Example: To limit 2 numbers of Dynamic Client for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ip verify source limit 2 4.2.65.
PAGE 116
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.42 ipv6 mld snooping immediate-leave Command: ipv6 mld snooping immediate-leave Default: Disabled Usage Guide: To enable MLD Snooping Immediate-leave (Fast Leave) for specific interface Example: To enable MLD Snooping Immediate-leave (Fast Leave) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ipv6 mld snooping immediate-leave 4.2.65.
PAGE 117
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.
PAGE 118
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.46 lacp key Command: lacp key <1-65535> | auto lacp Enable LACP on this interface key Key of the LACP aggregation <1-65535> Key value auto Choose a key based on port speed Default: Auto Usage Guide: To configure LACP key for specific interface Example: To configure LACP key (555) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lacp key 555 4.2.65.
PAGE 119
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.
PAGE 120
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-if) # lacp timeout slow 4.2.65.
PAGE 121
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp med media-vlan policy-list 2 4.2.65.52 lldp med transmit-tlv Command: lldp med transmit-tlv [ capabilities ] [ location ] [ network-policy ] lldp LLDP configurations med Media Endpoint Discovery transmit-tlv LLDP-MED Location Type Length Value parameter. capabilities Enable transmission of the optional capabilities TLV.
PAGE 122
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure LLDP Rx only mode for specific interface Example: To configure LLDP Rx only mode for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp receive 4.2.65.54 lldp tlv-select management-address Command: lldp tlv-select management-address lldp LLDP configurations tlv-select To transmit which optional TLVs. management-address Enable/Disable transmission of management address.
PAGE 123
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To enable port-description of LLDP TLV for specific interface Example: To enable port-description of LLDP TLV for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select port-description 4.2.65.56 lldp tlv-select system-capabilities Command: lldp tlv-select system-capabilities lldp LLDP configurations tlv-select To transmit which optional TLVs.
PAGE 124
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To enable system-description of LLDP TLV for specific interface Example: To enable system-description of LLDP TLV for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp tlv-select system-description 4.2.65.58 lldp tlv-select system-name Command: lldp tlv-select system-name lldp LLDP configurations tlv-select To transmit which optional TLVs.
PAGE 125
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Both (Tx +Rx) Usage Guide: To configure LLDP Tx only mode for specific interface Example: To configure LLDP Tx only mode for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # lldp transmit 4.2.65.
PAGE 126
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Shutdown Usage Guide: To configure action mode of Loop protection for specific interface Example: To configure action mode (log and shutdown) of Loop protection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect action shutdown log 4.2.65.
PAGE 127
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Enabled Usage Guide: To enable tx-mode of Loop protection for specific interface Example: To enable tx-mode of Loop protection for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # loop-protect tx-mode 4.2.65.
PAGE 128
Command Guide of GS-5220-16S8C and GS-5220-16S8CR rj45 rj45 interface (copper interface). sfp sfp interface (fiber interface). Default: N/A Usage Guide: To configure Copper or Fiber mode of media type for specific interface Example: To configure Copper mode of media type for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # media-type rj45 4.2.65.
PAGE 129
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable Immediate-leave of MVR for specific interface Example: To enable Immediate-leave of MVR for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # mvr immediate-leave 4.2.65.
PAGE 130
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: mvr vlan type [source | receiver ] mvr Multicast VLAN Registration configuration vlan MVR multicast vlan MVR multicast VLAN list type MVR port role configuration receiver MVR receiver port source MVR source port Default: Inactive Usage Guide: To configure port role of specific MVR VLAN ID for specific interface Example: To configure port role (source) of MVR VLAN ID (111) for GigabitEthernet X/X Switch# configu
PAGE 131
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-if) # network-clock synchronization ssm 4.2.65.71 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function for specific interface Example: To enable the function (network-clock synchronization ssm) for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # no network-clock synchronization ssm 4.2.65.
PAGE 132
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # ping ip 10.10.10.10 size 88 4.2.65.73 poe mode Command: poe mode { standard | plus } poe Power Over Ethernet. mode PoE mode. plus Set mode to PoE+ (Maximum power 30.0 W) standard Set mode to PoE (Maximum power 15.4 W) Default: N/A Usage Guide: To configure 802.3at/af mode for specific interface Example: To configure 802.3at mode for GigabitEthernet X/X.
PAGE 133
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure Ping PD IP Address of PoE for specific interface Example: To configure Ping PD IP Address (10.101.10.10) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck IP 10.101.10.10 4.2.65.75 poe pdcheck action Command: poe pdcheck action { reboot | alarm | reboot-alarm } poe Power Over Ethernet.
PAGE 134
Command Guide of GS-5220-16S8C and GS-5220-16S8CR poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. enable PD alive check enable. Default: Disabled Usage Guide: To enable PD Ping Alive Check function of PoE for specific interface. Example: To enable PD Ping Alive Check function of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck enable 4.2.65.
PAGE 135
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck interval 100 4.2.65.78 poe pdcheck reboot-time Command: poe pdcheck reboot-time <30-180> poe Power Over Ethernet. pdcheck Allows user to enable or disable per port PD Alive Check function. reboot-time set the PoE device rebooting time. <30-180> reboot-time <30-180> Default: 90 Usage Guide: To configure PD Ping Alive Check rebooting time of PoE for specific interface.
PAGE 136
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure PD Ping Alive Check retry count (5) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe pdcheck retry-count 5 4.2.65.80 poe power limit Command: poe power limit { } poe Power Over Ethernet. power limit Setting maximum power for port in allocation mode. The maximum power. Maximum power for the interface (0-15.
PAGE 137
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 2 Usage Guide: To configure interface priority of PoE for specific interface. Example: To configure interface priority (low) of PoE for GigabitEthernet X/X. Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # poe priority low 4.2.65.82 poe time-range Command: poe time-range { profile1 | profile2 | profile3 | profile4 } poe Power Over Ethernet. time-range To bind a PoE time-range to the corresponding port.
PAGE 138
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable Port-security for specific interface Example: To enable Port-security for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # port-security 4.2.65.84 port-security maximum Command: port-security maximum port-security maximum Enable/disable port security per interface.
PAGE 139
Command Guide of GS-5220-16S8C and GS-5220-16S8CR violation The action involved with exceeding the limit.
PAGE 140
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # port-security violation trap-shutdown 4.2.65.87 pvlan Command: pvlan pvlan Private VLAN list of PVLANs. Range is from 1 to number of ports.
PAGE 141
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # pvlan isolation 4.2.65.
PAGE 142
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dei 1 4.2.65.
PAGE 143
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure DSCP Classify of QoS for specific interface Example: To configure DSCP Classify (Any) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dscp-classify any 4.2.65.
PAGE 144
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure DSCP ingress translation of QoS for specific interface Example: To configure DSCP ingress translation of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos dscp-translate 4.2.65.
PAGE 145
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-if) # qos map cos-tag cos 1 dpl 1 pcp 6 dei 0 4.2.65.
PAGE 146
Command Guide of GS-5220-16S8C and GS-5220-16S8CR pcp Priority Code Point configuration Specific Priority Code Point Default: 0 Usage Guide: To configure PCP of QoS for specific interface Example: To configure PCP (6) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos pcp 6 4.2.65.
PAGE 147
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.
PAGE 148
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure Egress Queue (4) Shapers Rate (9999 Kbps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos queue-shaper queue 4 9999 4.2.65.
PAGE 149
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: 500 Usage Guide: To configure Broadcast Frames Storm Control Rate of QoS for specific interface Example: To configure Broadcast Frames Storm Control Rate (999 fps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos storm broadcast 999 fps 4.2.65.
PAGE 150
Command Guide of GS-5220-16S8C and GS-5220-16S8CR unknown Police unknown (flooded) frames fps Policer rate (default kbps) Rate is fps Default: 500 Usage Guide: To configure Unknown Frames Storm Control Rate of QoS for specific interface Example: To configure Unknown Frames Storm Control Rate (999 fps) of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos storm unicast 999 fps 4.2.65.
PAGE 151
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos tag-remark pcp 1 dei 1 4.2.65.
PAGE 152
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To enable DSCP Classification of QoS for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # qos trust dscp 4.2.65.
PAGE 153
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure RMON History Configuration for specific interface Example: To configure RMON History Configuration as below table for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # rmon collection history 1 buckets 5 interval 3 4.2.65.
PAGE 154
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # rmon collection stats 2 4.2.65.111 shutdown Command: shutdown shutdown Shutdown of the interface. Default: No shutdown Usage Guide: To shut down specific interface Example: To shut down GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # shutdown 4.2.65.
PAGE 155
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree 4.2.65.
PAGE 156
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree bpdu-guard 4.2.65.
PAGE 157
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To enable point to point mode (shared) of CIST Normal Port Configuration for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree edge 4.2.65.
PAGE 158
Command Guide of GS-5220-16S8C and GS-5220-16S8CR port-priority STP priority of this port Range (lower higher priority) auto Use auto cost Default: Auto Usage Guide: To configure Path Cost of CIST / MST Normal Port Configuration for specific interface Example: To enable Path Cost (32) of CIST / MST Normal Port Configuration (CIST) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # spanning-tree mst 0 port-priority 32
PAGE 159
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.
PAGE 160
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # speed 1000 4.2.65.
PAGE 161
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To add forbidden VLAN ID for specific interface Example: To add forbidden VLAN ID (5) for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport forbidden vlan add 5 4.2.65.
PAGE 162
Command Guide of GS-5220-16S8C and GS-5220-16S8CR hybrid Change PVID for hybrid port acceptable-frame-type all Set acceptable frame type on a port.
PAGE 163
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure VLAN list (None) of Hybrid VLAN for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport hybrid allowed vlan none 4.2.65.
PAGE 164
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Enabled Usage Guide: To enable Ingress-filtering with Hybrid VLAN mode for specific interface Example: To enable Ingress-filtering with Hybrid VLAN mode for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport hybrid ingress-filtering 4.2.65.
PAGE 165
Command Guide of GS-5220-16S8C and GS-5220-16S8CR port-type Set port type c-port Customer port s-custom-port Custom Provider port s-port Provider port unaware Port in not aware of VLAN tags.
PAGE 166
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport mode trunk 4.2.65.132 switchport vlan ip-subnet Command: switchport vlan ip-subnet id <1-128> vlan switchport Switching mode characteristics vlan VLAN commands ip-subnet VCL IP Subnet-based VLAN configuration. id id keyword <1-128> Unique VCE ID for each VCL entry (1-128) vlan Source IP address and mask (Format: xx.xx.xx.xx/mm.mm.
PAGE 167
Command Guide of GS-5220-16S8C and GS-5220-16S8CR mac MAC-based VLAN commands vlan 48 bit unicast MAC address: xx:xx:xx:xx:xx:xx vlan keyword VLAN ID required for the group to VLAN mapping (Range: 1-4095) Default: None Usage Guide: To configure MAC-based VLAN for specific interface Example: To configure MAC-based VLAN as below table for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport vlan mac 00:55:44
PAGE 168
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.65.
PAGE 169
Command Guide of GS-5220-16S8C and GS-5220-16S8CR oui Detect telephony device by OUI address Default: OUI Usage Guide: To configure Discovery-protocol in the Voice VLAN for specific interface Example: To configure Discovery-protocol (LLDP) in the Voice VLAN for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport voice vlan discovery-protocol lldp 4.2.65.
PAGE 170
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: switchport voice vlan security switchport Switching mode characteristics voice Voice appliance attributes vlan Vlan for voice traffic security Enable Voice VLAN port security mode Default: Disabled Usage Guide: To enable Voice VLAN security for specific interface Example: To enable Voice VLAN security for GigabitEthernet X/X Switch# configure terminal Switch (config)# interface GigabitEthernet X/X Switch (config-if) # switchport voice vlan
PAGE 171
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands in configure terminal mode Example: To run “show aaa” in configure terminal mode. Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# do show aaa console : local telnet : local ssh : local http : local 4.2.66.
PAGE 172
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# exit Switch (config)# 4.2.66.
PAGE 173
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: ip address dhcp ip Interface Internet Protocol config commands address Address configuraton dhcp Enable DHCP Default: None Usage Guide: To configure IP address mode for specific VLAN Example: To configure IP address mode (DHCP) for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip address dhcp 4.2.66.
PAGE 174
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.66.7 ip dhcp server Command: ip dhcp server ip Interface Internet Protocol config commands dhcp Configure DHCP server parameters server Enable DHCP server per VLAN Default: None Usage Guide: To enable IPv4 DHCP Server for specific VLAN Example: To enable IPv4 DHCP Server for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip dhcp server 4.2.66.
PAGE 175
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping 4.2.66.
PAGE 176
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 0 - 31744 tenths of seconds Default: 10 Usage Guide: To configure Last-member-query-interval of IGMP snooping for specific VLAN Example: To configure Last-member-query-interval (100 seconds) of IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping last-member-query-interval 1000 4.2.66.
PAGE 177
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.66.12 ip igmp snooping querier address Command: ip igmp snooping querier address ip Interface Internet Protocol config commands igmp Internet Group Management Protocol snooping Snooping IGMP querier IGMP Querier configuration address IGMP Querier address configuration A valid IPv4 unicast address Default: 0.0.0.
PAGE 178
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping querier election 4.2.66.
PAGE 179
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: 125 Usage Guide: To configure Querier-interval of IGMP snooping for specific VLAN Example: To configure Querier-interval (60 seconds) of IGMP snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ip igmp snooping query-max-response-time 600 4.2.66.
PAGE 180
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.66.
PAGE 181
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-if-vlan)# ipv6 address 2001::7788/64 4.2.66.19 ipv6 mld snooping Command: ipv6 mld snooping ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping Snooping MLD Default: Disabled Usage Guide: To enable MLD snooping for specific VLAN Example: To enable MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping 4.2.66.
PAGE 182
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure MLD snooping V2 for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping compatibility v2 4.2.66.
PAGE 183
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: 0 Usage Guide: To configure CoS priority of MLD snooping for specific VLAN Example: To configure CoS priority (5) of MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping priority 5 4.2.66.
PAGE 184
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.66.
PAGE 185
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping query-max-response-time 600 4.2.66.
PAGE 186
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure Unsolicited-Report-Interval of MLD snooping for specific VLAN Example: To configure Unsolicited-Report-Interval (99 seconds) of MLD snooping for VLAN X Switch# configure terminal Switch (config)# interface vlan X Switch (config-if-vlan)# ipv6 mld snooping unsolicited-report-interval 99 4.2.66.
PAGE 187
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# ip arp inspection 4.2.
PAGE 188
Command Guide of GS-5220-16S8C and GS-5220-16S8CR ip arp inspection translate ip Internet Protocol arp Address Resolution Protocol inspection translate ARP inspection arp inspection translate all entries Default: N/A Usage Guide: To translate dynamic entries into static ARP inspection table. Example: To translate dynamic entries into static ARP inspection table. Switch# configure terminal Switch (config)# ip arp inspection translate ARP Inspection: Translate 1 dynamic entries into static entries. 4.
PAGE 189
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# ip arp inspection translate interface GigabitEthernet 1/1 1 00:11:22:33:44:55 192.168.0.18 4.2.
PAGE 190
Command Guide of GS-5220-16S8C and GS-5220-16S8CR dhcp Dynamic Host Configuration Protocol excluded-address Prevent DHCP from assigning certain addresses Low IP address Default: N/A Usage Guide: To configure excluded IP range of DHCP Server. Example: To configure excluded IP range (192.168.0.100~192.168.0.101) of DHCP Server. Switch# configure terminal Switch (config)# ip dhcp excluded-address 192.168.0.100 192.168.0.101 4.2.
PAGE 191
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.1 broadcast Command: broadcast broadcast Broadcast address in use on the client's subnet Broadcast IP address Default: None Usage Guide: To configure Broadcast IP address (DHCP option 28) of DHCP Server Example: To configure Broadcast IP address (192.168.0.66) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# broadcast 192.168.0.
PAGE 192
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: client-identifier mac-address client-identifier mac-address Client identifier MAC address type of client identifier MAC address of client Default: None Usage Guide: To configure Bind IP to MAC of DHCP Server Example: To configure Bind IP to MAC (00:11:22:33:44:55) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# client-identifier mac-addres
PAGE 193
Command Guide of GS-5220-16S8C and GS-5220-16S8CR default-router default-router Default routers Router's IP address Default: None Usage Guide: To configure Default Gateway of DHCP Server Example: To configure Default Gateway (192.168.0.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# default-router 192.168.0.1 4.2.73.6 dns-server Command: dns-server dns-server DNS servers
PAGE 194
Command Guide of GS-5220-16S8C and GS-5220-16S8CR do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# do show aaa console : local telnet ssh http : local : local : local 4.2.73.
PAGE 195
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# end Switch# 4.2.73.10 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode.
PAGE 196
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: hardware-address hardware-address Client hardware address Client MAC address Default: None Usage Guide: To configure MAC address of DHCP Server while the pool is in the host type. Example: To configure MAC address (00:11:22:33:44:55) of DHCP Server for pool “planetbestswitch” while the pool is in the host type.
PAGE 197
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.13 lease Command: lease <0-365> <0-23> <0-59> | infinite lease Address lease time <0-365> Days <0-23> Hours <0-59> Minutes infinite Infinite lease Default: 1 day Usage Guide: To configure Lease Time of DHCP Server. Example: To configure Lease Time (119 minutes) of DHCP Server for pool “planetbestswitch”. Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# lease 0 1 59 4.2.73.
PAGE 198
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.15 netbios-node-type Command: netbios-node-type b-node | h-node | m-node | p-node netbios-node-type NetBIOS node type b-node Broadcast node h-node Hybrid node m-node Mixed node p-node Peer-to-peer node Default: None Usage Guide: To configure NetBIOS node type of DHCP Server. Example: To configure NetBIOS node type (B-node) of DHCP Server for pool “planetbestswitch”.
PAGE 199
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.17 network Command: network network Network number and mask Network number Network mask in dotted-decimal notation, excluding 255.255.255.255 Default: None Usage Guide: To configure Network IP address of DHCP Server. Example: To configure Network IP address (192.168.1.11/24) of DHCP Server for pool “planetbestswitch”.
PAGE 200
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.19 nis-server Command: nis-server nis-server Network information servers Server's IP address Default: None Usage Guide: To configure NIS Server of DHCP Server Example: To configure NIS Server (1.1.1.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# nis-server 1.1.1.1 4.2.73.
PAGE 201
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.73.21 ntp-server Command: ntp-server ntp-server NTP servers Server's IP address Default: None Usage Guide: To configure NTP Server of DHCP Server Example: To configure NTP Server (1.1.1.1) of DHCP Server for pool “planetbestswitch” Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# ntp-server 1.1.1.1 4.2.73.
PAGE 202
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# ip dhcp pool planetbestswitch Switch (config-dhcp-pool)# vendor class-identifier "0x8" specific-info 0x8 4.2.74 ip dns proxy Command: ip dns proxy ip Internet Protocol dns Domain Name System proxy DNS proxy service Default: Disabled Usage Guide: To enable DNS proxy. Example: To enable DNS proxy. Switch# configure terminal Switch (config)# ip dns proxy 4.2.
PAGE 203
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# ip helper-address 1.1.1.1 4.2.76 ip http secure-redirect Command: ip http secure-redirect ip Internet Protocol http Hypertext Transfer Protocol secure-redirect Secure HTTP web redirection Default: Disabled Usage Guide: To redirect WebUI from HTTP to HTTPs Example: To redirect WebUI from HTTP to HTTPs Switch# configure terminal Switch (config)# ip http secure-redirect 4.2.
PAGE 204
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To enable HTTPs WebUI. Switch# configure terminal Switch (config)# ip http secure-server 4.2.78 ip igmp host-proxy Command: ip igmp host-proxy ip Internet Protocol igmp Internet Group Management Protocol host-proxy IGMP proxy configuration Default: Disabled Usage Guide: To enable IGMP Proxy Example: To enable IGMP Proxy. Switch# configure terminal Switch (config)# ip igmp host-proxy 4.2.
PAGE 205
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To enable IGMP leave-proxy. Switch# configure terminal Switch (config)# ip igmp host-proxy leave-proxy 4.2.80 ip igmp snooping Command: ip igmp snooping ip Internet Protocol igmp Internet Group Management Protocol snooping Snooping IGMP Default: Disabled Usage Guide: To enable IGMP Snooping. Example: To enable IGMP Snooping. Switch# configure terminal Switch (config)# ip igmp snooping 4.2.
PAGE 206
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To enable IGMP Snooping for specific VLAN. Example: To enable IGMP Snooping for VLAN 1. Switch# configure terminal Switch (config)# ip igmp snooping vlan 1 4.2.
PAGE 207
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: ip igmp unknown-flooding ip Internet Protocol igmp Internet Group Management Protocol unknown-flooding Flooding unregistered IPv4 multicast traffic Default: Enabled Usage Guide: To flood unregistered IPv4 multicast traffic. Example: To flood unregistered IPv4 multicast traffic. Switch# configure terminal Switch (config)# ip igmp unknown-flooding 4.2.
PAGE 208
Command Guide of GS-5220-16S8C and GS-5220-16S8CR ip name-server dhcp ip Internet Protocol name-server dhcp Domain Name System Dynamic Host Configuration Protocol Default: None Usage Guide: To configure DNS IP address via DHCP Server. Example: To configure DNS IP address via DHCP Server. Switch# configure terminal Switch (config)# ip name-server 8.8.8.8 4.2.
PAGE 209
Command Guide of GS-5220-16S8C and GS-5220-16S8CR ip route ip Internet Protocol route Add IP route Network Netmask Gateway Default: None Usage Guide: To configure static route Example: To configure static route as below table. Switch# configure terminal Switch (config)# ip route 192.168.1.0 255.255.255.0 192.168.0.1 4.2.
PAGE 210
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.
PAGE 211
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To enable SSH service Switch# configure terminal Switch (config)# ip ssh 4.2.91 ip verify source Command: ip verify source ip Internet Protocol verify verify command source verify source Default: Disabled Usage Guide: To enable IP Source Guard Example: To enable IP Source Guard Switch# configure terminal Switch (config)# ip verify source 4.2.
PAGE 212
Command Guide of GS-5220-16S8C and GS-5220-16S8CR translate ip verify source translate all entries Default: Disabled Usage Guide: To translate dynamic entries to IP Source Guard table Example: To translate dynamic entries to IP Source Guard table Switch# configure terminal Switch (config)# ip verify source translate 4.2.
PAGE 213
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enter IPMC profile mode Example: To enter IPMC profile mode (planet) Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# 4.2.94.
PAGE 214
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To configure description for specific IPMC Profile Example: To configure description (999) for specific IPMC Profile (planet) Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# description 999 4.2.94.3 do Command: do < exec commands > do To run exec commands in config mode Default: N/A Usage Guide: To run exec commands Example: To run “show aaa”.
PAGE 215
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)#end Switch# 4.2.94.5 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# exit Switch (config)# 4.2.94.
PAGE 216
Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To default the function. Example: To enable the function (description 999). Switch# configure terminal Switch (config)# ipmc profile planet Switch (config-ipmc-profile)# no description 999 4.2.94.
PAGE 217
Command Guide of GS-5220-16S8C and GS-5220-16S8CR host-proxy MLD proxy configuration Default: Disabled Usage Guide: To enable MLD Proxy Example: To enable MLD Proxy. Switch# configure terminal Switch (config)# ipv6 mld host-proxy 4.2.
PAGE 218
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable MLD Snooping. Example: To enable MLD Snooping. Switch# configure terminal Switch (config)# ipv6 mld snooping 4.2.98 ipv6 mld snooping vlan Command: ipv6 mld snooping vlan ipv6 IPv6 configuration commands mld Multicast Listener Discovery snooping vlan Snooping MLD MLD VLAN VLAN identifier(s): VID Default: Disabled Usage Guide: To enable MLD Snooping for specific VLAN.
PAGE 219
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Prefix length ranges from 8 to 128 Default: ff3e:: /96 Usage Guide: To enable SSM Range of MLD. Example: To enable SSM Range (ff3e::7788/128) of MLD. Switch# configure terminal Switch (config)# ipv6 mld ssm-range ff3e::7788 128 4.2.
PAGE 220
Command Guide of GS-5220-16S8C and GS-5220-16S8CR interface vlan IPv6 unicast address (except link-local address) of next-hop Select an interface to configure VLAN Interface VLAN identifier(s): VID IPv6 link-local address of next-hop Default: None Usage Guide: To configure static route for IPv6 Example 1: To configure static route as below table for IPv6.
PAGE 221
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure LACP system-priority (99). Switch# configure terminal Switch (config)# lacp system-priority 99 4.2.103 line Command: line { <0~16> | console 0 | vty <0~15> } line Configure a terminal line <0~16> List of line numbers console Console terminal line vty Virtual terminal Default: N/A Usage Guide: To enter line mode Example: To enter line mode (vty 1) Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# 4.
PAGE 222
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# do show aaa console : local telnet ssh http : local : local : local 4.2.103.2 editing Command: editing editing Enable command line editing Default: Enabled Usage Guide: To allow user editing command line. Example: To allow user editing command line.
PAGE 223
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)#end Switch# 4.2.103.
PAGE 224
Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To configure EXEC timeout Example: To configure EXEC timeout (10 minutes) Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# exec-timeout 10 4.2.103.
PAGE 225
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To exit current mode. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# exit Switch (config)# 4.2.103.8 history size Command: history size <0-32> history size Control the command history function Set history buffer size <0-32> Number of history commands, 0 means disable Default: None Usage Guide: To exit current mode Example: To exit current mode.
PAGE 226
Command Guide of GS-5220-16S8C and GS-5220-16S8CR None Usage Guide: To configure displayed lines on a screen. Example: To configure displayed lines on a screen. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# length 10 4.2.103.10 location Command: location location Enter terminal location description One text line describing the terminal's location Default: None Usage Guide: To configure description of location.
PAGE 227
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To enable MOTD banner.. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# motd-banner 4.2.103.12 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (motd-banner) for vty 1 Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# no motd-banner 4.2.103.
PAGE 228
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure privilege level (5) for vty 1. Switch# configure terminal Switch (config)# line vty 1 Switch (config-line)# privilege level 5 4.2.103.14 width Command: width <0 or 40-512> width Set width of the display terminal <0 or 40-512> Number of characters on a screen line (0 for unlimited width) Default: 0 Usage Guide: To configure width of the display terminal. Example: To configure width (50) of the display terminal for vty 1.
PAGE 229
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To enable LLDP hold time Example: To enable LLDP hold time (5) Switch# configure terminal Switch (config)# lldp holdtime 5 4.2.105 lldp med datum Command: lldp med datum nad83-mllw | nad83-navd88 | wgs84 lldp LLDP configurations.
PAGE 230
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4 Usage Guide: To configure frame transmission time of LLDP Example: To configure frame transmission time (6) of LLDP Switch# configure terminal Switch (config)# lldp med fast 6 4.2.107 lldp med location-tlv altitude Command: lldp med location-tlv altitude [floors ] | [meters ] lldp LLDP configurations.
PAGE 231
Command Guide of GS-5220-16S8C and GS-5220-16S8CR elin-addr Emergency Location Identification Number, (e.g. E911 and others), such as defined by TIA or NENA. ELIN value Default: 0 Usage Guide: To configure Emergency Location Identification Number of LLDP-MED Example: To configure Emergency Location Identification Number (911) of LLDP-MED Switch# configure terminal Switch (config)# lldp med location-tlv elin-addr 911 4.2.
PAGE 232
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: lldp med location-tlv longitude east | west lldp LLDP configurations. med Media Endpoint Discovery location-tlv LLDP-MED Location Type Length Value parameter longitude Longitude parameter east Setting longitude direction to east. west Setting longitude direction to west. Longitude degrees (0.0000-180.
PAGE 233
Command Guide of GS-5220-16S8C and GS-5220-16S8CR The VLAN the policy uses tagged frames. dscp Differentiated Services Code Point. <0-63> DSCP value 0-63 l2-priority <0-7> Layer 2 priority. Priority 0-7 Default: 0 Usage Guide: To configure media-VLAN-policy of LLDP-MED Example: To configure media-VLAN-policy as below table of LLDP-MED Switch# configure terminal Switch (config)# lldp med media-vlan-policy 1 guest-voice tagged 1 dscp 45 l2-priority 5 4.2.
PAGE 234
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.113 lldp timer Command: lldp timer <5-32768> lldp LLDP configurations. timer Sets LLDP TX interval (The time between each LLDP frame transmitted in seconds) <5-32768> 5-32768 seconds. Default: 30 Usage Guide: To configure Tx interval time of LLDP Example: To configure Tx interval time (555) of LLDP Switch# configure terminal Switch (config)# lldp timer 555 4.2.
PAGE 235
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 2 Usage Guide: To configure Tx transmission-delay time of LLDP Example: To configure Tx transmission-delay time (88) of LLDP Switch# configure terminal Switch (config)# lldp transmission-delay 88 4.2.
PAGE 236
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Info Usage Guide: To configure level of log server Example: To configure level of log server Switch# configure terminal Switch (config)# logging level error 4.2.117 logging on Command: logging on logging on Syslog Enable syslog server Default: Disabled Usage Guide: To enable log server Example: To enable log server Switch# configure terminal Switch (config)# logging on 4.2.
PAGE 237
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To enable Loop Protection Switch# configure terminal Switch (config)# loop-protect 4.2.
PAGE 238
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure Transmission Time of Loop Protection Example: To configure Transmission Time (8) of Loop Protection Switch# configure terminal Switch (config)# loop-protect transmit-time 8 4.2.
PAGE 239
Command Guide of GS-5220-16S8C and GS-5220-16S8CR interface * Select an interface to configure All switches or All ports GigabitEthernet 1 Gigabit Ethernet Port 10GigabitEthernet 10 Gigabit Ethernet Port Default: 300 Usage Guide: To configure Static MAC Address Table Example: To configure Static MAC Address Table as below table Switch# configure terminal Switch (config)# mac address-table static 00:11:22:33:44:55 vlan 1 interface GigabitEthernet 1/1 4.2.
PAGE 240
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 1 ais fr1s 4.2.124 mep aps Command: mep aps [ multi | uni ] { laps | { raps [ octet ] } } mep Maintenance Entity Point The MEP instance number. aps Automatic Protection Switching protocol laps Linear Automatic Protection Switching protocol. multi OAM PDU is transmitted with multicast MAC. Must me 'multi' in case of RAPS.
PAGE 241
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: mep cc fr100s | fr10s | fr1m | fr1s | fr300s | fr6h | fr6m mep Maintenance Entity Point The MEP instance number. cc Continuity Check Priority in case of tagged OAM. In the EVC domain this is the COS-ID. fr100s Frame rate is 100 f/s. fr10s Frame rate is 10 f/s. fr1m Frame rate is 1 f/min. fr1s Frame rate is 1 f/s. fr300s Frame rate is 300 f/s. fr6h Frame rate is 6 f/hour.
PAGE 242
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: EVC Usage Guide: To configure Client Domain of MEP Example: To configure Client Domain (EVC) of MEP 1 Switch# configure terminal Switch (config)# mep 1 client domain evc 4.2.127 mep client flow Command: mep client flow level [ ais-prio [ | ais-highest ] ] [ lck-prio [ | lck-highest ] ] mep Maintenance Entity Point level The MEP instance number.
PAGE 243
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 1 client flow 5 level 4 ais-prio ais-highest lck-prio 3 4.2.128 mep dm Command: mep dm [ multi | { uni mep-id } ] [ single | dual ] [ rdtrp | flow ] interval last-n mep Maintenance Entity Point The MEP instance number. dm Delay Measurement Priority in case of tagged OAM.
PAGE 244
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 1 dm 5 rdtrp interval 10 last-n 10 4.2.129 mep dm ns Command: mep dm ns mep Maintenance Entity Point The MEP instance number. dm Delay Measurement ns Nano Seconds Default: us Usage Guide: To configure Delay Measurement of MEP Example: To configure Delay Measurement unit (ns) of MEP 1 as below table. Switch# configure terminal Switch (config)# mep 1 dm ns 4.2.
PAGE 245
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Keep Usage Guide: To reset Delay Measurement of MEP while overflowing Example: To reset Delay Measurement of MEP 1 while overflowing Switch# configure terminal Switch (config)# mep 1 dm overflow-reset 4.2.131 mep dm proprietary Command: mep dm proprietary mep Maintenance Entity Point dm The MEP instance number.
PAGE 246
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Enabled Usage Guide: To configure Time Sync of MEP. Example: To configure Time Sync of MEP 1 Switch# configure terminal Switch (config)# mep 1 dm syncronized 4.2.133 mep down Command: mep [ mip ] down domain { port | evc | vlan } [ vid ] flow level interface mep Maintenance Entity Point mip This MEP instance is a half-MIP down The MEP instance number.
PAGE 247
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 1 down domain port flow 1 level 0 interface GigabitEthernet 1/1 4.2.134 mep lb Command: mep lb [ dei ] [ multi | { uni { { mep-id } | { mac } } } ] count size interval mep Maintenance Entity Point lb The MEP instance number. Loop Back count Priority in case of tagged OAM. In the EVC domain this is the COS-ID.
PAGE 248
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 2 lb 1 dei count 10 size 64 interval 100 4.2.135 mep lck Command: mep lck fr1m | fr1s mep Maintenance Entity Point lck fr1m fr1s The MEP instance number. Locked Signal Frame rate is 1 f/min. Frame rate is 1 f/s. Default: 1 frame/sec Usage Guide: To configure Locked Frame Rate of MEP. Example: To configure Locked Frame Rate (1 frame/sec) of MEP 2.
PAGE 249
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure MEG level of MEP. Example: To configure MEG level (2) of MEP 2. Switch# configure terminal Switch (config)# mep 2 level 2 4.2.137 mep lm Command: mep lm [ multi | uni ] [ single | dual ] [ fr10s | fr1s | fr6m | fr1m | fr6h ] [ flr ] mep Maintenance Entity Point lm The MEP instance number. Loss Measurement Priority in case of tagged OAM. In the EVC domain this is the COS-ID.
PAGE 250
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 2 lm 5 uni flr 4 4.2.138 mep lt Command: mep lt { { mep-id } | { mac } } ttl mep Maintenance Entity Point lt The MEP instance number. Link Trace mac Priority in case of tagged OAM. In the EVC domain this is the COS-ID. Link Trace target unicast MAC to be used in case of LT against MIP.
PAGE 251
Command Guide of GS-5220-16S8C and GS-5220-16S8CR meg-id The MEP instance number. The ITU/IEEE MEG-ID The MEG-ID string. This is either the ITU MEG-ID or the IEEE Short MA, depending on the selected MEG-ID format. The ITU max. is 13 characters. The ITU-CC max. is 15 characters. The IEEE max. is 16 characters.. ieee itu The MEG-ID (Short MA Name) has IEEE Character String format. The meg-id max. is 16 characters. The MEG-ID has ITU format (ICC - UMC). The meg-id max.
PAGE 252
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure MEP-ID (5) of MEP 1. Switch# configure terminal Switch (config)# mep 1 mep-id 5 4.2.141 mep peer-mep-id Command: mep peer-mep-id [ mac ] mep Maintenance Entity Point peer-mep-id The MEP instance number. The peer MEP-ID The peer MEP-ID value mac The peer MAC. this will be overwritten by any learned MAC – through CCM reception.
PAGE 253
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable Performance Monitoring of MEP. Example: To enable Performance Monitoring of MEP 1 Switch# configure terminal Switch (config)# mep 1 performance-monitoring 4.2.143 mep tst Command: mep tst [ dei ] mep-id [ sequence ] [ all-zero | all-one | one-zero ] rate size mep Maintenance Entity Point tst The MEP instance number.
PAGE 254
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To enable Test Signal of MEP. Example: To enable Test Signal of MEP 1 as below table Switch# configure terminal Switch (config)# mep 1 tst 3 dei mep-id 2 sequence one-zero rate 10 size 68 4.2.144 mep up Command: mep [mip] up domain { port | evc | vlan } [ vid ] flow level interface mep Maintenance Entity Point The MEP instance number.
PAGE 255
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 2 up domain port vid 1 flow 1 level 2 interface GigabitEthernet 1/1 4.2.145 mep vid Command: mep vid mep Maintenance Entity Point The MEP instance number. vid The MEP VID The MEP VID value Default: 0 Usage Guide: To set VID of MEP. Example: To set VID (8) of MEP 1. Switch# configure terminal Switch (config)# mep 1 vid 8 4.2.
PAGE 256
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mep 1 voe 4.2.147 monitor destination Command: monitor destination interface 10GigabitEthernet | GigabitEthernet monitor Set monitor configuration destination The destination port.
PAGE 257
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# monitor source interface GigabitEthernet 1/1 both 4.2.149 mvr Command: mvr mvr Multicast VLAN Registration configuration Default: Disabled Usage Guide: To enable MVR Example: To enable MVR Switch# configure terminal Switch (config)# mvr 4.2.
PAGE 258
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# mvr name 123 channel 1 4.2.
PAGE 259
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure frame tagged of MVR profile Example: To configure frame tagged (frame tagged) of MVR profile (123) Switch# configure terminal Switch (config)# mvr name 123 frame tagged 4.2.
PAGE 260
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: 5 Usage Guide: To configure the Last Member Query Interval of MVR profile Example: To configure the Last Member Query Interval (50 seconds) of MVR profile (123) Switch# configure terminal Switch (config)# mvr name 123 last-member-query-interval 500 4.2.
PAGE 261
Command Guide of GS-5220-16S8C and GS-5220-16S8CR vlan MVR multicast vlan MVR multicast VLAN list Default: None Usage Guide: To create a profile of MVR VLAN Example: To create a profile of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 4.2.
PAGE 262
Command Guide of GS-5220-16S8C and GS-5220-16S8CR mvr vlan frame priority mvr Multicast VLAN Registration configuration vlan MVR multicast vlan MVR multicast VLAN list frame MVR control frame in TX priority Interface CoS priority CoS priority ranges from 0 to 7 Default: 0 Usage Guide: To configure the frame priority of MVR VLAN Example: To configure the frame priority (5) of MVR VLAN (123) Switch# configure terminal Switch (config)
PAGE 263
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.160 mvr vlan igmp-address Command: mvr vlan igmp-address mvr Multicast VLAN Registration configuration vlan MVR multicast vlan igmp-address MVR multicast VLAN list MVR address configuration used in IGMP A valid IPv4 unicast address Default: 0.0.0.0 Usage Guide: To configure the MVR address of MVR VLAN Example: To configure the MVR address (192.168.0.
PAGE 264
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure the Last Member Query Interval of MVR VLAN Example: To configure the Last Member Query Interval (50 seconds) of MVR VLAN (123) Switch# configure terminal Switch (config)# mvr vlan 123 last-member-query-interval 500 4.2.
PAGE 265
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To configure profile name of MVR VLAN Example: To configure profile name (6) of MVR VLAN (5) Switch# configure terminal Switch (config)# mvr vlan 5 name 6 4.2.164 network-clock clk-source aneg-mode Command: network-clock clk-source aneg-mode { master | slave | forced } network-clock network-clock clk-source clk-source - commands related to a specific clock source.
PAGE 266
Command Guide of GS-5220-16S8C and GS-5220-16S8CR no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (loop-protect) Switch# configure terminal Switch (config)# no loop-protect 4.2.166 ntp Command: ntp ntp Configure NTP Default: Disabled Usage Guide: To enable the NTP service Example: To enable the NTP service Switch# configure terminal Switch (config)# ntp 4.2.
PAGE 267
Command Guide of GS-5220-16S8C and GS-5220-16S8CR ipv6 address Default: None Usage Guide: To configure the IP addresses of NTP Server Example: To configure the IP address (9.9.9.9) of NTP Server for index 1 Switch# configure terminal Switch (config)# ntp server 1 ip-address 9.9.9.9 4.2.168 poe admin-mode enable Command: poe admin-mode enable poe Power Over Ethernet admin-mode enable Enable or disable global PoE management function.
PAGE 268
Command Guide of GS-5220-16S8C and GS-5220-16S8CR management mode Use management mode to configure PoE power management method. mode allocation-consumption Max. port power determined by allocated, and power is managed according to power consumption. allocation-reserved-power class-consumption class-reserved-power lldp-consumption Max. port power determined by alocated, and is managed according to reserved power. Max. port power determined by class, and power is managed according to power consumption.
PAGE 269
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# poe sequential enable 4.2.171 poe sequential interval Command: poe sequential interval <1-30> poe Power Over Ethernet sequential interval PoE sequential is to delay power feeding when the switch is completely booted. Set how long system should feeding power to next PoE interface <1-30> <1-30> poe sequential enable Default: 5 Usage Guide: To configure Sequential Power up Interval.
PAGE 270
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# poe sequential rule priority 4.2.173 poe supply Command: poe supply <1-XXX> poe Power Over Ethernet supply Use poe supply to specify the maximum power the power supply can deliver. <1-XXX> Maximum power the power supply can deliver. Default: Maximum Usage Guide: To configure Power Supply Budget. Example: To configure Power Supply Budget (200 watts).
PAGE 271
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# poe temperature-protection enable 4.2.175 poe temperature-threshold Command: poe temperature-threshold <0-100> poe Power Over Ethernet temperature-threshold <0-100> Set a lower high temperature threshold for the secondary temperature alarm in degrees C. Specifies the new threshold temperature. Default: 80 Usage Guide: To enable PoE Temperature Protection.
PAGE 272
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# poe usage-threshold 90 4.2.177 poe-time-range Command: poe-time-range {profile1 | profile2 | profile3 | profile4} poe-time-range Used to create PoE time-range for the switch and enter Power Time-range Create Configuration Mode.
PAGE 273
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#do show aaa console : local telnet : local ssh : local http : local 4.2.177.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#end Switch# 4.2.177.
PAGE 274
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)#exit Switch (config)# 4.2.177.4 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function. Example: To enable the function (description 999).
PAGE 275
Command Guide of GS-5220-16S8C and GS-5220-16S8CR < start_h: 0-23> <0-23> start hour < start_m: 0-59> <0-59> start minute to start to end < end_h: 0-23> <0-23> end hour < end_m: 0-59> <0-59> end minute reboot Enable reboot function < reboot_h: 0-23> <0-23> reboot hour < reboot_m:0-59> <0-59> reboot minute Default: N/A Usage Guide: To configure the Power Over Ethernet Schedule for specific profile. Example: To configure the Power Over Ethernet Schedule (below table) for specific profile 1.
PAGE 276
Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To configure the Power Over Ethernet Reboot Schedule for specific profile. Example: To configure the Power Over Ethernet Reboot Schedule (below table) for specific profile. Switch# configure terminal Switch (config)# poe-time-range profile1 Switch (config-poe-time-range)# reboot Mon 0 0 4.2.
PAGE 277
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable the Port Aging Example: To enable the Port Aging Switch# configure terminal Switch (config)# port-security port-security aging 4.2.
PAGE 278
Command Guide of GS-5220-16S8C and GS-5220-16S8CR dhcp-pool DHCP Pool Configuration Mode exec Exec mode if-vlan VLAN Interface Mode interface Port List Interface Mode ipmc-profile IPMC Profile Mode line Line configuration mode rfc2544-profile RFC2544 Profile Mode snmps-host SNMP Server Host Mode stp-aggr STP Aggregation Mode level Set privilege level of command <0-15> Privilege level Initial valid words and literals of the command to modify Default: None Usage Guide: To configu
PAGE 279
Command Guide of GS-5220-16S8C and GS-5220-16S8CR af21 Assured Forwarding PHB AF21(DSCP 18) af22 Assured Forwarding PHB AF22(DSCP 20) af23 Assured Forwarding PHB AF23(DSCP 22) af31 Assured Forwarding PHB AF31(DSCP 26) af32 Assured Forwarding PHB AF32(DSCP 28) af33 Assured Forwarding PHB AF33(DSCP 30) af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assured Forwarding PHB AF42(DSCP 36) af43 Assured Forwarding PHB AF43(DSCP 38) be Default PHB(DSCP 0) for best effort traffic cs1 Class Select
PAGE 280
Command Guide of GS-5220-16S8C and GS-5220-16S8CR af12 Assured Forwarding PHB AF12(DSCP 12) af13 Assured Forwarding PHB AF13(DSCP 14) af21 Assured Forwarding PHB AF21(DSCP 18) af22 Assured Forwarding PHB AF22(DSCP 20) af23 Assured Forwarding PHB AF23(DSCP 22) af31 Assured Forwarding PHB AF31(DSCP 26) af32 Assured Forwarding PHB AF32(DSCP 28) af33 Assured Forwarding PHB AF33(DSCP 30) af41 Assured Forwarding PHB AF41(DSCP 34) af42 Assured Forwarding PHB AF42(DSCP 36) af43 Assured Forwardi
PAGE 281
Command Guide of GS-5220-16S8C and GS-5220-16S8CR map Global QoS Map/Table dscp-cos Map for dscp to cos Specific DSCP af11 Assured Forwarding PHB AF11(DSCP 10) af12 Assured Forwarding PHB AF12(DSCP 12) af13 Assured Forwarding PHB AF13(DSCP 14) af21 Assured Forwarding PHB AF21(DSCP 18) af22 Assured Forwarding PHB AF22(DSCP 20) af23 Assured Forwarding PHB AF23(DSCP 22) af31 Assured Forwarding PHB AF31(DSCP 26) af32 Assured Forwarding PHB AF32(DSCP 28) af33 Assured Forwa
PAGE 282
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.
PAGE 283
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure the DSCP Egress Translation Example: To configure the DSCP Egress Translation (AF11 to AF12) Switch# configure terminal Switch (config)# qos map dscp-egress-translation af11 to af12 4.2.
PAGE 284
Command Guide of GS-5220-16S8C and GS-5220-16S8CR va Voice Admit PHB(DSCP 44) Default: None Usage Guide: To configure the DSCP Ingress Translation Example: To configure the DSCP Ingress Translation (AF11 to AF12) Switch# configure terminal Switch (config)# qos map dscp-ingress-translation af11 to af12 4.2.
PAGE 285
Command Guide of GS-5220-16S8C and GS-5220-16S8CR interface Interfaces last Place QCE at the end next Place QCE before the next QCE ID smac tag Setup matched SMAC Setup tag options Default: None Usage Guide: To configure the QCE Example: To configure the QCE 1 (below table) for interface GigabitEthernet 1/1-2 Switch# configure terminal Switch (config)# qos qce 1 interface GigabitEthernet 1/1-2 tag type tagged vid 5 pcp 3 dei 1 dmac unicast frame-type ipv4 proto udp dscp 19 frag no sport 55 action c
PAGE 286
Command Guide of GS-5220-16S8C and GS-5220-16S8CR [ inner-tag { [ type { untagged | tagged | c-tagged | s-tagged | any } ] [ vid { | any } ] [ pcp { | any } ] [ dei { | any } ] } ] [ frame-type { any | { etype [ { | any } ] } | { llc [ dsap { | any } ] [ ssap { | any } ] [ control { | any } ] } | { snap [ { | any } ] } | { ipv4 [ proto { | tcp | udp | any } ] [ sip { | any } ] [ dip { | any } ] [ dscp
PAGE 287
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.189 qos qce refresh Command: qos qce refresh qos Quality of Service qce QoS Control Entry refresh Refresh QCE tables in hardware Default: None Usage Guide: To refresh the QCE Example: To refresh the QCE. Switch# configure terminal Switch (config)# qos qce refresh 4.2.
PAGE 288
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Specific drop probability in percent Default: Usage Guide: To configure the Weighted Random Early Detection Example: To configure the Weighted Random Early Detection (below table) Switch# configure terminal Switch (config)# qos wred queue 1 min-th 2 mdp-1 3 mdp-2 4 mdp-3 5 4.2.
PAGE 289
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# radius-server attribute 32 planet 4.2.192 radius-server attribute 4 Command: radius-server attribute 4 radius-server 4 Configure RADIUS NAS-IP-Address Default: None Usage Guide: To configure the NAS-IP-Address Example: To configure the NAS-IP-Address (7.7.7.7) Switch# configure terminal Switch (config)# radius-server attribute 4 7.7.7.7 4.2.
PAGE 290
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.194 radius-server deadtime Command: radius-server deadtime radius-server deadtime Configure RADIUS Time to stop using a RADIUS server that doesn't respond Time in minutes Default: 0 Usage Guide: To configure the Deadtime of Radius-Server Example: To configure the Deadtime (15) of Radius-Server Switch# configure terminal Switch (config)# radius-server deadtime 15 4.2.
PAGE 291
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To configure the Host of Radius-Server Example: To configure the Host (below table) of Radius-Server Switch# configure terminal Switch (config)# radius-server host planet.com.tw timeout 10 retransmit 6 key 123456789 4.2.
PAGE 292
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.197 radius-server retransmit Command: radius-server retransmit radius-server retransmit Configure RADIUS Specify the number of retries to active server Number of retries for a transaction Default: 3 Usage Guide: To configure the retransmitted time of Radius-Server Example: To configure the retransmitted time (5) of Radius-Server Switch# configure terminal Switch (config)# radius-server retransmit 5 4.2.
PAGE 293
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.
PAGE 294
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To configure the Alarm of RMON Example: To configure the Alarm (below table) of RMON Switch# configure terminal Switch (config)# rmon alarm 1 .1.3.6.1.2.1.2.2.1.10.15 50 absolute rising-threshold 1000 1 falling-threshold 520 1 falling 4.2.
PAGE 295
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.201 sflow agent-ip Command: sflow agent-ip { ipv4 | ipv6 } sflow Statistics flow agent-ip The agent IP address used as agent-address in UDP datagrams. Defaults to IPv4 loopback address. Default: None Usage Guide: To configure the agent IP address of sFlow Example: To configure the agent IP address (10.10.10.10) of sFlow Switch# configure terminal Switch (config)# sflow agent-ip ipv4 10.10.10.10 4.2.
PAGE 296
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.203 sflow collector-port Command: sflow collector-port sflow Statistics flow collector-port Collector UDP port Port number Default: None Usage Guide: To configure the Collector port number of sFlow Example: To configure the Collector port number (555) of sFlow Switch# configure terminal Switch (config)# sflow collector-port 555 4.2.
PAGE 297
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.205 sflow timeout Command: sflow timeout sflow Statistics flow timeout Receiver timeout measured in seconds. The switch decrements the timeout once per second, and as long as it is non-zero, the receiver receives samples. Once the timeout reaches 0, the receiver and all its configuration is reset to defaults.
PAGE 298
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# sfp temperature-threshold 55 4.2.207 snmp-server Command: snmp-server snmp-server Set SNMP server's configurations Default: Enabled Usage Guide: To enable the SNMP Service Example: To enable the SNMP Service Switch# configure terminal Switch (config)# snmp-server 4.2.
PAGE 299
Command Guide of GS-5220-16S8C and GS-5220-16S8CR write view name Default: None Usage Guide: To configure the Access of SNMP Example: To configure the Access (below table) of SNMP Switch# configure terminal Switch (config)# snmp-server access default_rw_group model v2c level priv read default_view write default_view 4.2.
PAGE 300
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# snmp-server community v3 public 192.168.0.15 255.255.255.0 4.2.
PAGE 301
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure the Engine IDof SNMP Example: To configure the Engine ID (1234567890) of SNMP Switch# configure terminal Switch (config)# snmp-server engine-id local 1234567890 4.2.
PAGE 302
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To run “show aaa”. Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#do show aaa console : local telnet : local ssh http : local : local 4.2.212.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#end Switch# 4.2.212.
PAGE 303
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To exit current mode Example: To exit current mode. Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)#exit Switch (config)# 4.2.212.
PAGE 304
Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.212.5 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (host planet.com 66 informs) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# no ip address dhcp 4.2.212.
PAGE 305
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# informs retries 2 timeout 55 4.2.212.7 shutdown Command: shutdown shutdown Disable the trap configuration Default: Disabled Usage Guide: To disable Trap mode of SNMP Example: To disable Trap mode of SNMP Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# shutdown 4.2.212.
PAGE 306
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To configure Trap event of SNMP Example: To configure Trap event (STP, RMON) of SNMP Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# traps switch rmon stp 4.2.212.
PAGE 307
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-snmps-host)# version v2 planet 4.2.213 spanning-tree aggregation Command: spanning-tree aggregation spanning-tree aggregation Spanning Tree protocol Aggregation mode Default: None Usage Guide: To enter aggregation mode of STP Example: To enter aggregation mode of STP Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)# 4.2.213.1 do Command: do < exec commands > do To run exec commands.
PAGE 308
Command Guide of GS-5220-16S8C and GS-5220-16S8CR ssh http : local : local 4.2.213.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# spanning-tree aggregation Switch (config-stp-aggr)#end Switch# 4.2.213.3 exit Command: exit exit Exit from current mode Default: None Usage Guide: To exit current mode Example: To exit current mode.
PAGE 309
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# 4.2.213.4 no Command: no no Negate a command or set its defaults Default: N/A Usage Guide: To default the function Example: To disable the function (spanning-tree auto-edge) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# no spanning-tree auto-edge 4.2.213.
PAGE 310
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config-snmps-host)# spanning-tree auto-edge 4.2.213.6 spanning-tree bpdu-guard Command: spanning-tree bpdu-guard spanning-tree bpdu-guard Spanning Tree protocol Enable/disable BPDU guard Default: Disabled Usage Guide: To enable the BPDU Guard of CIST Aggregated Port Example: To enable the BPDU Guard of CIST Aggregated Port Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree bpdu-guard 4.
PAGE 311
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree edge 4.2.213.
PAGE 312
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure the Path Cost of MSTI Port Example: To configure the Path Cost (321) of MSTI Port (MST 2) Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree mst 2 cost 321 4.2.213.
PAGE 313
Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable the Restricted Role of CIST Example: To enable the Restricted Role of CIST Switch# configure terminal Switch (config)# snmp-server host planet Switch (config-snmps-host)# spanning-tree restricted-role 4.2.213.
PAGE 314
Command Guide of GS-5220-16S8C and GS-5220-16S8CR VLAN list < translation_vlan > translation VLAN ID Default: None Usage Guide: To configure the VLAN Translation Example: To enable the VLAN Translation (below table) Switch# configure terminal Switch (config)# switchport vlan mapping 1 3 5 4.2.
PAGE 315
Command Guide of GS-5220-16S8C and GS-5220-16S8CR tacacs-server host [ port ] [ timeout ] [ key ] tacacs-server host Configure TACACS+ Specify a TACACS+ server Hostname or IP address key Server specific key (overrides default) port TCP port for TACACS+ server timeout TCP port number Time to wait for this TACACS+ server to reply (overrides default) Wait time in seconds The shared key D
PAGE 316
Command Guide of GS-5220-16S8C and GS-5220-16S8CR To configure SMTP authentication's username (123@planet.com.tw) and password (456) Switch# configure terminal Switch (config)# transport email authentication username 123@planet.com.tw password 456 4.2.218 transport email from Command: transport email from subject transport Enable or disable transport email function. email Enable or disable transport email function.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-317.html>PAGE 317</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR <1-65535> port_number: Specifies the port number. The range is from 1 to 65535. The default port number is 25. Default: N/A Usage Guide: To configure SMTP Server address and port number. Example: To configure SMTP Server address (mail.planet.com.tw) and port number (123) Switch# configure terminal Switch (config)# transport email smtp-server mail.planet.com.tw port 123 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-318.html>PAGE 318</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: Disabled Usage Guide: To enable the UPnP service Example: To enable the UPnP service Switch# configure terminal Switch (config)# upnp 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-319.html>PAGE 319</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: 4 Usage Guide: To configure the TTL of UPnP Example: To configure the TTL (8) of UPnP Switch# configure terminal Switch (config)# upnp ttl 8 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-320.html>PAGE 320</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Password: 1234 # 4.2.225 vlan Command: vlan <vlist> vlan VLAN commands <vlan_list> VLAN IDs 1~4095 Default: None Usage Guide: To create the VLAN Profiles Example: To create the VLAN Profiles (VLAN 5) Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# 4.2.225.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-321.html>PAGE 321</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# vlan 5 Switch (config-vlan)#do show aaa console : local telnet : local ssh http : local : local 4.2.225.2 end Command: end end Go back to EXEC mode Default: Auto Usage Guide: To back to EXEC mode Example: To back to EXEC mode Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)#end Switch# 4.2.225.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-322.html>PAGE 322</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# exit Switch (config)# 4.2.225.4 name Command: name <vlan_name> name ASCII name of the VLAN <vword32> The ASCII name for the VLAN Default: None Usage Guide: To configure description of VLAN Example: To configure description (FAE) of VLAN Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# name FAE 4.2.225.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-323.html>PAGE 323</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# configure terminal Switch (config)# vlan 5 Switch (config-vlan)# no name FAE 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-324.html>PAGE 324</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR llc LLC-based VLAN group <0x0-0xff> DSAP (Range: 0x00 - 0xFF) <0x0-0xff> SSAP (Range: 0x00 - 0xFF) snap SNAP-based VLAN group <0x0-0xffffff> rfc-1042 SNAP OUI (Range 0x000000 - 0XFFFFFF) SNAP OUI is rfc-1042 snap-8021h group SNAP OUI is 8021h Protocol-based VLAN group commands <grp_id> Group Name (Range: 1 - 16 characters) Default: None Usage Guide: To configure the Protocol-based VLAN Example: To configure the Protocol-based VLAN (below table</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-325.html>PAGE 325</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.2.229 voice vlan aging-time Command: voice vlan aging-time <aging_time> voice vlan Voice appliance attributes Vlan for voice traffic aging-time Set secure learning aging time <agingtime : 10-10000000> Aging time, 10-10000000 seconds Default: 86400 Usage Guide: To configure the Aging Time of Voice VLAN Example: To configure the Aging Time of Voice VLAN Switch# configure terminal Switch (config)# voice vlan aging-time 8888 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-326.html>PAGE 326</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure the Traffic Class (5) of Voice VLAN Switch# configure terminal Switch (config)# voice vlan class 5 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-327.html>PAGE 327</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Usage Guide: To configure the VID of Voice VLAN Example: To configure the VID (66 ) of Voice VLAN Switch# configure terminal Switch (config)# voice vlan vid 66 4.2.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-328.html>PAGE 328</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch (config)# web privilege group Aggregation level cro 3 crw 4 sro 3 srw 5 4.3 copy 4.3.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-329.html>PAGE 329</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To configure Description of Debug Prompt Example: To configure Description (1233) of Debug Prompt Switch # debug prompt 1233 1233# 4.5 delete 4.5.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-330.html>PAGE 330</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # dir Directory of flash: r- 1970-01-01 00:00:00 648 default-config rw 1970-01-01 07:26:26 1833 startup-config 2 files, 2481 bytes total. 4.6 dir 4.6.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-331.html>PAGE 331</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR disable Turn off privileged commands Default: None Usage Guide: To exit enable mode Example: To exit enable mode Switch # disable Switch > 4.8 do 4.8.1 do Command: do < exec commands > do To run exec commands. Default: N/A Usage Guide: To run exec commands. Example: To run “show aaa”.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-332.html>PAGE 332</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.9 dot1x 4.9.1 dot1x initialize Command: dot1x initialize [ interface ( <port_type> [ <plist> ] ) ] dot1x IEEE Standard for port-based Network Access Control initialize Force re-authentication immediately Default: N/A Usage Guide: To re-authenticate specific interface immediately. Example: To re-authenticate specific interface (GigabitEthernet 1/1) immediately. Switch# dot1x initialize interface GigabitEthernet 1/1 4.10 enable 4.10.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-333.html>PAGE 333</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch > enable Switch # 4.11 erps 4.11.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-334.html>PAGE 334</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.12 exit 4.12.1 exit Command: exit exit Exit from EXEC mode Default: None Usage Guide: To exit EXEC mode Example: To exit EXEC mode Switch # disable Switch > exit Press ENTER to get started 4.13 firmware 4.13.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-335.html>PAGE 335</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To swap Active and Alternate firmware image Switch # firmware swap 4.13.2 firmware upgrade Command: firmware upgrade <tftpserver_path_file> firmware Firmware upgrade/swap upgrade Firmware upgrade <tftpserver_path_file : word> TFTP Server IP address, path and file name for the server containing the new image. Default: None Usage Guide: To upgrade firmware via TFTP Server Example: To upgrade firmware via TFTP Server (File: tftp://192.168.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-336.html>PAGE 336</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To do DHCP renew for specific VLAN Example: To do DHCP renew for specific VLAN (6) Switch # ip dhcp retry interface vlan 6 4.15 logout 4.15.1 logout Command: logout logout Exit from EXEC mode Default: None Usage Guide: To exit EXEC mode Example: To exit EXEC mode Switch # logout Press ENTER to get started 4.16 more 4.16.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-337.html>PAGE 337</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: None Usage Guide: To view the file Example: To view the file (222) Switch # copy running-config flash:222 Building configuration... % Saving 2038 bytes to flash:222 Switch # more flash:222 hostname Switch username admin privilege 15 password none ! vlan 1 ! vlan 5 ! ! ! 4.17 no 4.17.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-338.html>PAGE 338</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# no erps 1 command force port0 4.18 ping 4.18.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-339.html>PAGE 339</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.18.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-340.html>PAGE 340</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.19 reload 4.19.1 reload cold Command: reload cold reload Reload system cold Reload cold. Default: N/A Usage Guide: To restart the device. Example: To restart the device. Switch# reload cold 4.19.2 reload defaults Command: reload defaults [ keep-ip ] reload defaults keep-ip Reload system Reload defaults without rebooting. Attempt to keep VLAN1 IP setup. Default: N/A Usage Guide: To store the device factory default settings.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-341.html>PAGE 341</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch# reload defaults 4.20 send 4.20.1 send Command: send { * | console 0 | vty <vty_list> } <message> reload Reload system * All tty lines console vty Primary terminal line Virtual terminal Default: N/A Usage Guide: To send message for command line user. Example: To send message ( hi, I will upgrade the firmware, OK? ) for command line user (All). Switch # send * 1 Enter TEXT message. End with the character '1'.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-342.html>PAGE 342</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21 show 4.21.1 show aaa Command: show aaa show Show running system information aaa Login methods Default: N/A Usage Guide: To display the AAA services. Example: To display the AAA services Switch # show aaa console : local telnet ssh : local : local http : local 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-343.html>PAGE 343</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To display Access Management Statistics. Switch # show access management statistics Access Management Statistics: ----------------------------HTTP Receive: 0 Allow: 0 Discard: 0 HTTPS Receive: 0 Allow: 0 Discard: 0 SNMP Receive: 0 Allow: 0 Discard: 0 TELNET Receive: 0 Allow: 0 Discard: 0 SSH Receive: 0 Allow: 0 Discard: 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-344.html>PAGE 344</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch access-list rate limiter ID 4 is 1 pps Switch access-list rate limiter ID 5 is 1 pps Switch access-list rate limiter ID 6 is 1 pps Switch access-list rate limiter ID 7 is 1 pps Switch access-list rate limiter ID 8 is 1 pps Switch access-list rate limiter ID 9 is 1 pps Switch access-list rate limiter ID 10 is 1 pps Switch access-list rate limiter ID 11 is 1 pps Switch access-list rate limiter ID 12 is 1 pps Switch access-list rate limiter ID 13 is 1 pp</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-345.html>PAGE 345</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To display the ACL Statistics, Rate Limiter List, ACE Statistics. Example: To display the ACL Statistics, Rate Limiter List, ACE Statistics for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-346.html>PAGE 346</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-347.html>PAGE 347</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR LOAM: Link OAM User ID ---- -- Frame ----- Action Rate L. CPU Counter Conflict ------ -------- ------ ------- -------- DHCP 1 UDP Deny Disabled Yes 0 No DHCP 2 UDP Deny Disabled Yes 0 No PTP 1 EType Deny Disabled Yes 0 No PTP 2 EType Deny Disabled Yes 0 No Switch 1 access-list ace number: 4 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-348.html>PAGE 348</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To display the Aggregation mode status. Example: To display the Aggregation mode status. Switch # show aggregation mode Aggregation Mode: SMAC : Enabled DMAC : Disabled IP : Enabled Port : Enabled 4.21.8 show clock Command: show clock show Show running system information clock Configure time-of-day clock Default: N/A Usage Guide: To display the system time. Example: To display the system time.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-349.html>PAGE 349</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.9 show clock detail Command: show clock detail show Show running system information clock Configure time-of-day clock detail Display detailed information Default: N/A Usage Guide: To display the detailed system time. Example: To display the detailed system time. Switch # show clock detail System Time : 1970-01-01T00:29:25+00:00 Timezone : Timezone Offset : 0 ( 0 minutes) Timezone Acronym : Daylight Saving Time Mode : Disabled.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-350.html>PAGE 350</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.10 show dot1x statistics Command: show dot1x statistics show Show running system information dot1x IEEE Standard for port-based Network Access Control statistics all Shows statistics for either eapol or radius Show all dot1x statistics eapol Show EAPOL statistics radius Show Backend Server statistics interface Interface Default: N/A Usage Guide: To display the IEEE 802.1X statistics. Example: To display the All of IEEE 802.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-351.html>PAGE 351</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Rx Auth. Failures: 0 4.21.11 show dot1x status Command: show dot1x status [ interface ( <port_type> [ <v_port_type_list> ] ) ] [ brief ] show Show running system information dot1x IEEE Standard for port-based Network Access Control status Shows dot1x status, such as admin state, port state and last source. interface Interface brief Show status in a brief format Default: N/A Usage Guide: To display the IEEE 802.1X status.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-352.html>PAGE 352</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.12 show eps Command: show eps [ <inst> ] [ detail ] show Show running system information eps Ethernet Protection Switching <inst : range_list> detail The range of EPS instances Show detailed state including configuration information Default: N/A Usage Guide: To display the EPS instance information. Example: To display the EPS instance 1 detailed information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-353.html>PAGE 353</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.13 show erps Command: show erps [ <groups> ] [ detail | statistics ] show Show running system information erps Ethernet Ring Protection Switching <groups> Zero or more ERPS group numbers detail Show detailed information statistics Show statistics Default: N/A Usage Guide: To display the ERPS group information. Example: To display the ERPS group 1 detailed information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-354.html>PAGE 354</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Port 0 Block Status :BLOCKED Port 1 Block Status :BLOCKED R-APS Transmission :STOPPED R-APS Port 0 Reception :NONE R-APS Port 1 Reception :NONE FOP Alarm :OFF 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-355.html>PAGE 355</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.15 show evc statistics Command: show green-ethernet [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information green-ethernet Green ethernet (Power reduction) Default: N/A Usage Guide: To display the EVC statistics. Example: To display the EVC Red Frames statistics for all.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-356.html>PAGE 356</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show green-ethernet interface * 4.21.17 show green-ethernet energy-detect Command: show green-ethernet energy-detect [ interface ( <port_type> [ <port_list> ] ) ] show Show running system information green-ethernet energy-detect interface Green ethernet (Power reduction) Shows green ethernet energy-detect status for a specific port or ports. Shows green ethernet status for a specific port or ports.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-357.html>PAGE 357</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show green-ethernet short-reach interface * 4.21.19 show history Command: show history show Show running system information history Display the session command history Default: N/A Usage Guide: To display the command history. Example: To display the command history.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-358.html>PAGE 358</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR To display the SFP Transceiver information. Example: To display the SFP Transceiver information for interface GigabitEthernet 1/1. Switch # show interface GigabitEthernet 1/1 capabilities GigabitEthernet 1/1 Capabilities: SFP Type: None SFP Vendor name: SFP Vendor PN: SFP Vendor revision: 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-359.html>PAGE 359</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR ---------------------- ------------------ GigabitEthernet 1/1 ------------------ 0 0 4.21.22 show interface <port_type> <port_type_list> status Command: show interface <port_type> <port_type_list> status show Show running system information interface Interface status and configuration status Display status Default: N/A Usage Guide: To display the port status. Example: To display the port status for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-360.html>PAGE 360</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To display the VLAN mode for interface GigabitEthernet 1/1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-361.html>PAGE 361</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR GigabitEthernet 1/1 OK 3 Pair C Length Pair D Length ------ ------ ------ ------- OK 3 OK OK 3 3 4.21.25 show interface <port_type> <port_type_list> veriphy Command: show interface <port_type> <port_type_list> veriphy show Show running system information interface veriphy Interface status and configuration Run cable diagnostics and show result. Default: N/A Usage Guide: To display the result of Cable Diagnostics.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-362.html>PAGE 362</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR interface vlan Interface status and configuration VLAN status Default: N/A Usage Guide: To display the MAC address and IP address of specific VLAN. Example: To display the MAC address and IP address for all VLANs. Switch # show interface vlan VLAN1 LINK: 00-30-4F-00-99-00 Mtu:1500 <up broadcast running multicast> IPv4: 192.168.0.100/24 192.168.0.255 IPv6: fe80:2::201:c1ff:fe00:9900/64 <anycast tentative autoconf> 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-363.html>PAGE 363</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.28 show ip arp inspection Command: show ip arp inspection show ip arp Show running system information Internet Protocol Address Resolution Protocol inspection ARP inspection Default: N/A Usage Guide: To display the ARP Inspection Configuration. Example: To display the ARP Inspection Configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-364.html>PAGE 364</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To display the ARP Inspection Configuration. Example: To display the ARP Inspection Configuration. Switch # show ip arp inspection ARP Inspection Mode : disabled Port Port Mode Check VLAN ---------- Log Type ---- --------- -------- GigabitEthernet 1/1 disabled disabled NONE GigabitEthernet 1/2 disabled disabled NONE 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-365.html>PAGE 365</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-366.html>PAGE 366</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Rx NAK: 0 Tx NAK: 0 Rx Release: 0 Tx Release: 0 Rx Inform: 0 Tx Inform: 0 Rx Lease Query: 0 Tx Lease Query: 0 Rx Lease Unassigned: 0 Tx Lease Unassigned: 0 Rx Lease Unknown: 0 Tx Lease Unknown: 0 Rx Lease Active: 0 Tx Lease Active: 0 Rx Lease Active: 0 Tx Lease Active: 0 Rx Discarded checksum error: 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-367.html>PAGE 367</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 01 192.168.0.100 192.168.0.101 4.21.33 show ip dhcp pool Command: show ip dhcp pool [ <pool_name> ] show ip Show running system information Internet Protocol dhcp Dynamic Host Configuration Protocol pool DHCP pools information Default: N/A Usage Guide: To display the DHCP pools information. Example: To display the DHCP pools information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-368.html>PAGE 368</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Client name is - 4.21.34 show ip dhcp relay Command: show ip dhcp relay [ statistics ] show Show running system information ip Internet Protocol dhcp Dynamic Host Configuration Protocol relay DHCP relay agent configuration statistics Traffic statistics Default: N/A Usage Guide: To display the DHCP relay information. Example: To display the DHCP relay information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-369.html>PAGE 369</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR To display the DHCP Server Mode Configuration. Example: To display the DHCP Server Mode Configuration. Switch # show ip dhcp server DHCP server is globally disabled. All VLANs are disabled. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-370.html>PAGE 370</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.37 show ip dhcp server declined-ip (GG) Command: show ip dhcp server declined-ip show ip Show running system information Internet Protocol dhcp Dynamic Host Configuration Protocol server DHCP server information declined-ip Declined IP address Default: N/A Usage Guide: To display the DHCP Decline information. Example: To display the DHCP Decline information. Switch # show ip dhcp server declined-ip 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-371.html>PAGE 371</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show ip dhcp server statistics Database Counters ========================= POOL 2 Excluded IP 1 Declined IP 0 ========================= Binding Counters ========================= Automatic Manual Expired 0 0 0 ========================= Message Received Counters ========================= DISCOVER 0 REQUEST 0 DECLINE 0 RELEASE 0 INFORM 0 ========================= Message Sent Counters ========================= OFFER 0 ACK 0</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-372.html>PAGE 372</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR dhcp Dynamic Host Configuration Protocol snooping DHCP snooping interface Select an interface to configure Default: N/A Usage Guide: To display the DHCP Snooping configuration. Example: To display the DHCP Snooping configuration for GigabitEthernet 1/1. Switch # show ip dhcp snooping interface GigabitEthernet 1/1 GigabitEthernet 1/1 untrusted 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-373.html>PAGE 373</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.41 show ip http server secure status Command: show ip http server secure status show ip Show running system information Internet Protocol http Hypertext Transfer Protocol server HTTP web server secure Secure status Status Default: N/A Usage Guide: To display the DHCP Snooping table. Example: To display the DHCP Snooping table.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-374.html>PAGE 374</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To display the IGMP Snooping information. Example: To display the IGMP Snooping information (Detail). Switch # show ip igmp snooping detail IGMP Snooping is disabled to stop snooping IGMP control plane. Multicast streams destined to unregistered IGMP groups will be flooding. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-375.html>PAGE 375</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.44 show ip interface brief Command: show ip interface brief show Show running system information ip Internet Protocol interface brief IP interface status and configuration Brief IP interface status Default: N/A Usage Guide: To display the IP interface status. Example: To display the IP interface status. Switch # show ip interface brief Vlan Address Method Status ---- -------------------- -------- -----1 192.168.0.100/24 Manual UP 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-376.html>PAGE 376</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Current DNS server is 8.8.8.8 set by STATIC. 4.21.46 show ip route Command: show ip route show ip Show running system information Internet Protocol route Display the current ip routing table Default: N/A Usage Guide: To display the IP Routing table. Example: To display the IP Routing table. Switch # show ip route 11.11.11.0/24 via 192.168.0.14 <up gateway hw_rt> 127.0.0.1/32 via 127.0.0.1 <up host> 192.168.0.0/24 via VLAN1 <up hw_rt> 224.0.0.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-377.html>PAGE 377</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To display the Static IP Source Guard Table. Example: To display the Static IP Source Guard Table. Switch # show ip source binding interface GigabitEthernet 1/1 Type Port ---- ---- Static VLAN IP Address ---- ---------- GigabitEthernet 1/1 1 192.168.0.22 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-378.html>PAGE 378</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To display the IP statistics. Example: To display the IP statistics.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-379.html>PAGE 379</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Bcast: 768 received, 0 sent IPv4 ICMP statistics: Rcvd: 2618 Messages, 0 Error Sent: 2618 Messages, 0 Error ICMP message statistics: IPv4 ICMP Message: Echo Reply Rcvd: 0 Packet Sent: 2618 Packets IPv4 ICMP Message: Echo Rcvd: 2618 Packets Sent: 0 Packet 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-380.html>PAGE 380</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.51 show ipmc profile Command: show ipmc profile [ <profile_name> ] [ detail ] show Show running system information ipmc IPv4/IPv6 multicast configuration profile IPMC profile configuration <profilename : word16> detail Profile name Detail information of a profile Default: N/A Usage Guide: To display the IP Multicast Profile. Example: To display the IP Multicast Profile.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-381.html>PAGE 381</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR To display the IP Multicast Range. Example: To display the IP Multicast Range. Switch # show ipmc range Range Name :1 Start Address: 224.24.24.24 End Address : 224.24.24.25 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-382.html>PAGE 382</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Rcvd: 3 total in 168 bytes 3 local destination, 0 forwarding 0 header error, 0 address error, 0 unknown protocol 0 no route, 0 truncated, 0 discarded Sent: 17 total in 1104 bytes 17 generated, 0 forwarded 0 discarded Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fragment) 0 fragment created Mcast: 3 received in 168 bytes 17 sent in 1104 bytes Bcast: 0 received, 0 sent 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-383.html>PAGE 383</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR MLD Snooping is disabled to stop snooping MLD control plane. Multicast streams destined to unregistered MLD groups will be flooding. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-384.html>PAGE 384</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To display the IPv6 neighbor information. Example: To display the IPv6 neighbor information. Switch # show ipv6 neighbor 2001::7766 via VLAN1: 00-30-4F-00-99-00 Permanent/REACHABLE fe80::201:c1ff:fe00:9900 via VLAN1: 00-30-4F-00-99-00 Permanent/REACHABLE 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-385.html>PAGE 385</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-386.html>PAGE 386</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Mcast: 24 received in 2064 bytes 34 sent in 2208 bytes Bcast: 0 received, 0 sent IP interface statistics: IPv6 Statistics on Interface VLAN: 1 Rcvd: 12 total in 1032 bytes 3 local destination, 0 forwarding 0 header error, 0 address error, 0 unknown protocol 0 no route, 0 truncated, 9 discarded Sent: 17 total in 1104 bytes 17 generated, 0 forwarded 0 discarded Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble) 0 fragment (0 fragmented, 0 couldn't fr</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-387.html>PAGE 387</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.59 show lacp Command: show lacp { internal | statistics | system-id | neighbour } show Show running system information lacp LACP configuration/status internal Internal LACP configuration neighbour statistics Neighbour LACP status Internal LACP statistics system-id LACP system id Default: N/A Usage Guide: To display the LACP mode information. Example: To display the LACP mode information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-388.html>PAGE 388</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To display the VTY information. Example: To display the VTY information. Switch # show line alive Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-389.html>PAGE 389</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show lldp med media-vlan-policy Policy Id 0 Application Type Tag Voice Vlan ID L2 Priority DSCP Tagged 1 0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-390.html>PAGE 390</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR To display the LLDP neighbors information. Switch # show lldp neighbors No LLDP entries found 4.21.64 show lldp statistics Command: show lldp statistics [ interface ( <port_type> [ <port_type_list> ] ) ] show Show running system information lldp Display LLDP neighbors information statistics Display LLDP statistics information interface Interface to display Default: N/A Usage Guide: To display the LLDP statistics information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-391.html>PAGE 391</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR switch Switch <switch_list> Switch ID list in 1 Default: N/A Usage Guide: To display the Syslog information. Example: To display the Syslog information with Log ID 235861. Switch # show logging 235861 Switch : 1 ID : 235861 Level : Warning Time : 1970-01-01T13:33:57+00:00 Message: Loop Detected: Port 5 shut down 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-392.html>PAGE 392</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR GigabitEthernet 1/1 -----------------------------Loop protect mode is enabled. Actions are both of shutdown and log. Transmit mode is enabled. No loop. The number of loops is 12390. Time of last loop is at 1970-01-01T14:58:28+00:00 Status is down. 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-393.html>PAGE 393</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Static 1 33:33:00:00:00:01 GigabitEthernet 1/1-25 10GigabitEthernet 1/1-4 CPU Static 1 33:33:00:00:00:02 GigabitEthernet 1/1-25 10GigabitEthernet 1/1-4 CPU Static 1 33:33:ff:00:99:00 GigabitEthernet 1/1-25 10GigabitEthernet 1/1-4 CPU Dynamic 1 Static 1 d4:3d:7e:fd:e3:ac GigabitEthernet 1/21 ff:ff:ff:ff:ff:ff GigabitEthernet 1/1-25 10GigabitEthernet 1/1-4 CPU 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-394.html>PAGE 394</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-395.html>PAGE 395</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR MLD MVR VLAN 1 (Name is 1) interface is enabled. Querier status is IDLE RX MLD Query:0 V1Report:0 V2Report:0 V1Done:0 TX MLD Query:0 / (Source) Specific Query:0 Interface Channel Profile: <no associated profile> 4.21.70 show network-clock Command: show network-clock show Show running system information network-clock Show selector state Default: N/A Usage Guide: To display the SyncE information. Example: To display the SyncE information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-396.html>PAGE 396</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: show ntp status show ntp Show running system information Configure NTP status status Default: N/A Usage Guide: To display the NTP Server information. Example: To display the NTP Server information. Switch # show ntp status NTP Mode : enabled Idx --1 Server IP host address (a.b.c.d) or a host name string -----------------------------------------------------192.168.0.44 2 3 4 5 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-397.html>PAGE 397</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show platform phy interface GigabitEthernet 1/1 Port API Inst WAN/LAN/1G Mode ---- --------- --------- ---- 1 Default 1G ANEG Duplex Speed Link ------ ----- ---- - - No 4.21.73 show platform phy failover Command: show platform phy failover show Show running system information platform phy Platform specific information PHYs' information failover Failover status Default: N/A Usage Guide: To display the PHY failover status.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-398.html>PAGE 398</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To display the PHY ID. Example: To display the PHY ID for GigabitEthernet 1/1. Switch # show platform phy id interface GigabitEthernet 1/1 Port Channel ---- API Base ------- 1 0 -------0 (1g) Phy Id Phy Rev. ------8634 -----0 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-399.html>PAGE 399</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR show port-security port [ interface ( <port_type> [ <port_type_list> ] ) ] show Show running system information port-security port port-security Show MAC Addresses learned by Port Security interface Search by port Default: N/A Usage Guide: To display the MAC Addresses of Port Security. Example: To display the MAC Addresses of Port Security.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-400.html>PAGE 400</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 8 = 802.1X D = DHCP Snooping V = Voice VLAN Interface Users State MAC Cnt ----------------------- ----- ------------- ------- GigabitEthernet 1/1 ---- No users 0 4.21.78 show privilege Command: show privilege show Show running system information privilege Display command privilege Default: N/A Usage Guide: To display the Privilege information. Example: To display the Privilege information. Switch # show privilege 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-401.html>PAGE 401</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show pvlan PVLAN ID Ports -------- ----------------------------------------------------------------------------- 1 GigabitEthernet 1/1, GigabitEthernet 1/2, GigabitEthernet 1/3, 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-402.html>PAGE 402</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR interface maps Interface Global QoS Maps/Tables cos-dscp Map for cos to dscp dscp-classify dscp-cos Map for dscp classify enable Map for dscp to cos dscp-egress-translation Map for dscp egress translation dscp-ingress-translation Map for dscp ingress translation qce QoS Control Entry <qce> QCE ID wred Weighted Random Early Discard Default: N/A Usage Guide: To display the QoS configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-403.html>PAGE 403</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR qos policer mode: disabled, rate: 500 kbps qos queue-policer queue 0 mode: disabled, rate: 500 kbps qos queue-policer queue 1 mode: disabled, rate: 500 kbps qos queue-policer queue 2 mode: disabled, rate: 500 kbps qos queue-policer queue 3 mode: disabled, rate: 500 kbps qos queue-policer queue 4 mode: disabled, rate: 500 kbps qos queue-policer queue 5 mode: disabled, rate: 500 kbps qos queue-policer queue 6 mode: disabled, rate: 500 kbps qos queue-policer qu</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-404.html>PAGE 404</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR qos storm unknown mode: disabled, rate: 500 kbps 4.21.82 show radius-server Command: show radius-server [ statistics ] show Show running system information radius-server statistics RADIUS configuration RADIUS statistics Default: N/A Usage Guide: To display the RADIUS Server configuration. Example: To display the RADIUS Server configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-405.html>PAGE 405</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To display the RMON Alarm configuration. Example: To display the RMON Alarm ID 1 configuration. Switch # show rmon alarm 1 Alarm ID : 1 ---------------Interval : 30 Variable : .1.3.6.1.2.1.2.2.1.20.1 SampleType Value : deltaValue :0 Startup : risingOrFallingAlarm RisingThrld :2 FallingThrld :1 RisingEventIndex : 2 FallingEventIndex : 1 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-406.html>PAGE 406</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Event ID : 1 ---------------Description Type :2 : none Community LastSent : public : Never 4.21.85 show rmon history Command: show rmon history [ <id_list> ] show Show running system information rmon RMON statistics history Display the RMON history table Default: N/A Usage Guide: To display the RMON History configuration. Example: To display the RMON History ID 1 configuration.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-407.html>PAGE 407</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR statistics Display the RMON statistics table Default: N/A Usage Guide: To display the RMON Statistics configuration. Example: To display the RMON Statistics ID 1 configuration. Switch # show rmon statistics 1 Statistics ID : 1 --------------------Data Source : .1.3.6.1.2.1.2.2.1.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-408.html>PAGE 408</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR running-config all-defaults feature Show running system information Include most/all default values Show configuration for specific feature <feature_name> Valid words are 'GVRP' 'access' 'access-list' 'aggregation' 'arp-inspection' 'auth' 'clock' 'dhcp' 'dhcp-snooping''dhcp_server' 'dns' 'dot1x' 'eps' 'erps' 'evc' 'green-ethernet' 'http' 'icli' 'ip-igmp-snooping' 'ip-igmp-snooping-port' 'ip-igmp-snooping-vlan' 'ipmc-profile' 'ipmc-profile-range' 'ipv4' '</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-409.html>PAGE 409</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR ! vlan 1 ! ! ! mvr mvr vlan 1 name 1 4.21.88 show snmp Command: show snmp show Show running system information snmp Display SNMP configurations Default: N/A Usage Guide: To display the SNMP information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-410.html>PAGE 410</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR SNMPv3 Users Table: User Name : default_user Engine ID : 800007e5017f000001 Security Level : NoAuth, NoPriv Authentication Protocol : None Privacy Protocol : None SNMPv3 Groups Table; Security Model : v1 Security Name : public Group Name : default_ro_group Security Model : v1 Security Name : private Group Name : default_rw_group Security Model : v2c Security Name : public Group Name : default_ro_group Security Model : v2c Security Name</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-411.html>PAGE 411</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Security Level : NoAuth, NoPriv Read View Name : default_view Write View Name : default_view SNMPv3 Views Table: View Name : default_view OID Subtree : .1 View Type : included 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-412.html>PAGE 412</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Group Name : default_rw_group Security Model Security Level : any : NoAuth, NoPriv Read View Name : default_view Write View Name : default_view 4.21.90 show snmp community v3 Command: show snmp community v3 [ <community> ] show Show running system information snmp Display SNMP configurations community v3 Community SNMPv3 <community : word127> Specify community name Default: N/A Usage Guide: To display the SNMPv3 Community information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-413.html>PAGE 413</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: show snmp host [ <conf_name> ] [ system ] [ switch ] [ interface ] [ aaa ] show Show running system information snmp Display SNMP configurations host Set SNMP host's configurations <confname : word32> aaa Name of the host configuration AAA event group interface switch Interface event group Switch event group system System event group Default: N/A Usage Guide: To display the SNMP Host information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-414.html>PAGE 414</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR BRIDGE-MIB : - dot1dBase (.1.3.6.1.2.1.17.1) - dot1dTp (.1.3.6.1.2.1.17.4) Dot3-OAM-MIB : - dot3OamMIB (.1.3.6.1.2.1.158) ENTITY-MIB : - entityMIBObjects (.1.3.6.1.2.1.47.1) EtherLike-MIB : - transmission (.1.3.6.1.2.1.10) IEEE8021-MSTP-MIB : - ieee8021MstpMib (.1.3.111.2.802.1.1.6) IEEE8021-PAE-MIB : - ieee8021paeMIB (.1.0.8802.1.1.1.1) IEEE8023-LAG-MIB : - lagMIBObjects (.1.2.840.10006.300.43.1) IF-MIB : - ifMIB (.1.3.6.1.2.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-415.html>PAGE 415</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Q-BRIDGE-MIB : - qBridgeMIB (.1.3.6.1.2.1.17.7) RADIUS-ACC-CLIENT-MIB : - radiusAccClientMIBObjects (.1.3.6.1.2.1.67.2.2.1) RADIUS-AUTH-CLIENT-MIB : - radiusAuthClientMIBObjects (.1.3.6.1.2.1.67.1.2.1) RFC1213-MIB : - system (.1.3.6.1.2.1.1) - interfaces (.1.3.6.1.2.1.2) - ip (.1.3.6.1.2.1.4) - snmp (.1.3.6.1.2.1.5) - tcp (.1.3.6.1.2.1.6) - udp (.1.3.6.1.2.1.7) RMON-MIB : - statistics (.1.3.6.1.2.1.16.1) - history (.1.3.6.1.2.1.16.2) - alarm (.1.3.6.1.2.1.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-416.html>PAGE 416</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR snmp Display SNMP configurations mib MIB(Management Information Base) ifmib IF-MIB ifIndex The IfIndex that is defined in IF-MIB Default: N/A Usage Guide: To display the SNMP MIB ifIndex contexts. Example: To display the SNMP MIB ifIndex contexts.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-417.html>PAGE 417</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 27 Switch 1 - Port 27 10GigabitEthernet 1/3 28 Switch 1 - Port 28 10GigabitEthernet 1/4 29 Switch 1 - Port 29 GigabitEthernet 1/25 50001 VLAN 1 vlan 1 60001 IP Interface 1 vlan 1 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-418.html>PAGE 418</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Group Name : default_ro_group Security Model : v2c Security Name : private Group Name : default_rw_group Security Model : v3 Security Name : default_user Group Name : default_rw_group 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-419.html>PAGE 419</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR show snmp view [ <view_name> <oid_subtree> ] show Show running system information snmp Display SNMP configurations view MIB view configuration <viewname : word32> <oidsubtree : word255> MIB view name MIB view OID Default: N/A Usage Guide: To display the SNMP viewer information. Example: To display the SNMP viewer information. Switch # show snmp view View Name : default_view OID Subtree : .1 View Type : included 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-420.html>PAGE 420</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR To display the STP information. Example: To display the STP information. Switch # show spanning-tree CIST Bridge STP Status Bridge ID : 32768.00-30-4F-00-99-00 Root ID : 32768. 00-30-4F-00-99-00 Root Port :- Root PathCost: 0 Regional Root: 32768. 00-30-4F-00-99-00 Int.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-421.html>PAGE 421</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR ---- ---------- 2 1 4.21.99 show tacacs-server Command: show tacacs-server show Show running system information tacacs-server TACACS+ configuration Default: N/A Usage Guide: To display the TACACS+ Server configuration. Example: To display the TACACS+ Server configuration. Switch # show tacacs-server Global TACACS+ Server Timeout : 5 seconds Global TACACS+ Server Deadtime : 0 minutes Global TACACS+ Server Key : No hosts configured! 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-422.html>PAGE 422</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Default: N/A Usage Guide: To display the your login information. Example: To display the your login information. Switch # show terminal Line is con 0. * You are at this line now. Alive from Console. Default privileged level is 2. Command line editing is enabled Display EXEC banner is enabled. Display Day banner is enabled. Terminal width is 80. length is 24. history size is 32. exec-timeout is 10 min 0 second. Current session privilege is 15.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-423.html>PAGE 423</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Switch # show upnp UPnP Mode : Disabled UPnP TTL :4 UPnP Advertising Duration : 100 4.21.102 show users Command: show users [ myself ] show Show running system information users Display information about terminal lines myself Display information about mine Default: N/A Usage Guide: To display the user status. Example: To display the user status for all. Switch # show users Line is con 0. * You are at this line now. Connection is from Console.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-424.html>PAGE 424</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.103 show version Command: show version show Show running system information version System hardware and software status Default: N/A Usage Guide: To display the software and system information. Example: To display the software and system information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-425.html>PAGE 425</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR --------------Image : managed.bk Version : 000 Date : 2013-10-02T15:15:04+02:00 Product : Planet Best Switch Software Version : 000 Build Date : 2013-12-06T15:22:03+01:00 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-426.html>PAGE 426</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR id Show a specific ip-subnet entry Default: N/A Usage Guide: To display the IP-based VLAN information. Example: To display the IP-based VLAN information. Switch # show vlan ip-subnet VCE ID IP Address ------ --------------- 1 Mask Length VID ----------- ---- 192.168.78.0 Interfaces ---------- 24 5 GigabitEthernet 1/1 4.21.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-427.html>PAGE 427</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Command: show vlan protocol [ eth2 { <etype> | arp | ip | ipx | at } ] [ snap { <oui> | rfc-1042 | snap-8021h } <pid> ] [ llc <dsap> <ssap> ] show Show running system information vlan VLAN status protocol eth2 Protocol-based VLAN status Ethernet protocol based VLAN status <etype> Ether Type(Range: 0x600 - 0xFFFF) arp Ether Type is ARP at Ether Type is AppleTalk ip Ether Type is IP ipx Ether Type is IPX llc LLC-based VLAN status <dsap> DSAP</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-428.html>PAGE 428</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR 4.21.108 show voice vlan Command: show voice vlan [ oui <oui> | interface ( <port_type> [ <port_list> ] ) ] show Show running system information voice Voice appliance attributes vlan Vlan for voice traffic interface Select an interface to configure oui OUI configuration <oui> OUI value Default: N/A Usage Guide: To display the Voice VLAN information.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-429.html>PAGE 429</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR level Web privilege group level Default: N/A Usage Guide: To display the Web privilege group.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-430.html>PAGE 430</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR System 5 10 1 10 Timer 5 10 5 10 UPnP 5 10 5 10 VCL 5 10 5 10 VLAN_Translation 5 10 5 10 VLANs 5 10 5 10 Voice_VLAN 5 10 5 10 XXRP 5 10 5 10 ZL_3034X_API 5 10 5 10 4.22 terminal 4.22.1 terminal editing Command: terminal editing terminal editing Set terminal line parameters Enable command line editing Default: Enabled Usage Guide: To enable editing mode for current terminal session.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-431.html>PAGE 431</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR N/A Usage Guide: To configure idle timeout of EXEC mode for current terminal session. Example: To configure idle timeout with 500 minutes of EXEC mode for current terminal session. Switch # terminal exec-timeout 500 4.22.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/planet-technology/gs-5220-16s8c/user-guide-catalan-english-french-dutch/page-432.html>PAGE 432</a></h6><p>Command Guide of GS-5220-16S8C and GS-5220-16S8CR Example: To configure length of command display with 5 lines for current terminal session. Switch # terminal length 5 Switch # show run Building configuration... username admin privilege 15 password none loop-protect -- more --, next page: Space, continue: g, quit: ^C 4.22.</p></li></ul></nav></div></section></section></main><footer class=page-footer><div class="container flex-column py-3 py-sm-4"><div class="row mb-1 mb-sm-2 mb-md-5"><a href=/ class="brand offset-sm-0 col-sm-4 col-md-3 col-lg-2 offset-2 col-8 text-center text-md-start"><img class=logo-small src=/assets/img/brand-large.png alt=Manualshelf></a></div><div class=row><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Who We Are</dt><dd><a class=text-decoration-none href=/about>About Us</a></dd><dd><a class=text-decoration-none href=/company>Company</a></dd><dd><a class=text-decoration-none href=/careers>Careers</a></dd><dd><a class=text-decoration-none href=/terms>Terms & Privacy</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Resources</dt><dd><a class=text-decoration-none href=/brands>List of Manufacturers</a></dd><dd><a href=/ class=text-decoration-none>Support</a></dd><dd><a class=text-decoration-none href=/press>For the Press</a></dd><dd><a class=text-decoration-none href=/press#assets>Media assets</a></dd><dd><a class=text-decoration-none href=/faq>FAQ</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Get in touch</dt><dd><a class=text-decoration-none href=#>Blog</a></dd><dd><a class=text-decoration-none href=#>Email</a></dd><dd><a class=text-decoration-none href=/dmca>DMCA</a></dd></dl></div><div class=row><div class="text-center text-sm-start col-sm-4 pe-sm-0"><a href=https://www.facebook.com/pages/ManualShelf/1488826334681423 class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-facebook-f"></i></a><a href=https://www.twitter.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-twitter"></i></a><a href=https://plus.google.com/+ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-google-plus-g"></i></a><a href=http://www.pinterest.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none"><i class="fab fa-pinterest-p"></i></a></div><div class="col col-sm-8 d-flex flex-column align-items-center flex-sm-row flex-wrap flex-sm-nowrap justify-content-center justify-content-sm-end"><div class="copy w-auto d-flex align-items-center justify-content-center justify-content-sm-end mt-2 mt-sm-0 me-2">ManualShelf © 2013-2025</div><select class="form-select form-select-sm w-auto mt-2 mt-sm-0"><option value=usa>USA</option></select><div></div></div><div id=pixel><script> googletag.cmd.push(function() { googletag.display('pixel'); }); </script></div></footer><script src=/assets/js/jquery-3.3.1.min.js></script><script src=/assets/js/bootstrap.bundle.min.js></script><script src=/assets/js/jquery.autocomplete.min.js></script><script type=text/javascript> $.extend({ redirectPost: function(location, args) { var form = ''; $.each(args, function(key, value) { form += '<input type="hidden" name="' + key + '" value="' + value + '">'; }); form = '<form id="s1" action="' + location + '" method="POST">' + form + '</form>'; $(document.body).append(form); $("#s1").submit(); } }); $(document).ready(function(){ $("#query").autocomplete({ minChars: 3, groupBy: 'type', paramName: 'q', dataType: 'json', serviceUrl: '/autocomplete', noCache: true, showNoSuggestionNotice: true, noSuggestionNotice: 'Zarro results found', onSelect: function (suggestion) { $.redirectPost(suggestion.data.url, {highlight: encodeURIComponent(JSON.stringify(suggestion.data.hls))}); } }); var toc = $('.toc-selector'); if (toc.length) { var slideParams = { duration: 800, easing: 'linear' }; toc.click(function() { $(this).toggleClass('open'); var section = $('.toc-content'); var isCollapsed = section.attr('data-collapsed') === 'true'; if (isCollapsed) { section.slideDown(slideParams) section.attr('data-collapsed', 'false') } else { section.slideUp(slideParams); section.attr('data-collapsed', 'true') } }); } }); var lastSmall = $(window).width() < 576; $(window).resize(function() { var newSmall = $(window).width() < 576; if (lastSmall != newSmall) { lastSmall = newSmall; window.location.href = window.location.href; } }); </script></body></html>