L2/L4 Managed Gigabit Ethernet Switch GS-4210 802.
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 4 3. Terminal Setup............................................................................................ 5 3.1 Logging on to the Console.................................................................... 6 3.2 Configuring IP Address via the Console.................
1. Package Contents Thank you for purchasing PLANET L2/L4 Managed Gigabit Ethernet Switch. The descriptions of this series are shown below: 4-port 10/100/1000T 802.3bt PoE + 4-port 10/100/1000T GS-4210-8HP2T2S 802.3at PoE + 2-port 10/100/1000T + 2-port 100/1000X SFP Managed Switch GS-4210-8HP2S 2-port 10/100/1000T 802.3bt PoE + 6-port 10/100/1000T 802.3at PoE + 2-port 100/1000X SFP Managed Switch GS-4210-16UP4C 16-port 10/100/1000T 802.
2. Requirements zz Workstations running Windows XP/2003/2008/Vista/7/8/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-to-RS-232 converter. The above Workstations have been installed with terminal emulator, such as Hyper Terminal included in Windows XP/2003, putty or tera term.
3. Terminal Setup The Managed Switch is equipped with a console interface for local switch setup and maintenance. To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to the RJ45 type of the console port of the Managed Switch.
3.1 Logging on to the Console Once the terminal is connected to the device, power on the Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows, and the login screen in Figure 3-2 appears. Username: admin Password: admin Figure 3-2: Managed Switch Console Login Screen The user can now enter commands to manage the Managed Switch.
3.2 Configuring IP Address via the Console The Managed Switch is shipped with default IP address as follows: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows: Showing the current IP address 1. At the “GS-4210 Series#” prompt, enter “show ip”. 2. The screen displays the current IP Address, Subnet Mask and Gateway as shown in Figure 3-3.
Configuring IP address 3. At the“GS-4210 Series#” prompt, enter “configure”. 4. At the “GS-4210 Series(config)#” prompt, enter the following command and press as shown in Figure 3-4. GS-4210 Series(config)# ip address 192.168.1.100 mask 255.255.255.0 GS-4210 Series(config)# ip default-gateway 192.168.1.254 The previous command would apply the following settings for the Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.254 Figure 3-4: IP Address Screen 5.
3.3 Storing Current Switch Configuration In the Managed switch, the running configuration file is stored in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by writing the command or copying the running-config startup-config command, so that the running configuration sequence becomes the startup configuration file, which is the configuration saved. 1.
4. Starting Web Management The following shows how to start up the Web Management of the Managed Switch. Note the Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0. PC / Workstation with Web Browser 192.
2. When the following dialog box appears, please enter the default user name and password “admin”. The login screen in Figure 4-2 appears. Default Username: admin Default Password: admin Figure 4-2: Login Screen 3. After entering the password, the main screen appears as Figure 4-3 shows.
The Switch Menu on the top of the Web page lets you access all the commands and statistics the Managed Switch provides. The Switch Menu always contains one or more buttons, such as “System”, “Switching”, “QoS”, “Security”, “PoE” and “Maintenance”. Figure 4-4: Switch Menu Now, you can use the Web management interface to continue the Switch management. Please refer to the user’s manual for more.
4.2 Saving Configuration via the Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click “Save > Save Configurations to FLASH” to log in to the “Configuration Manager” page. 2. Press the “Apply” button to save running configuration to start up configuration.
5. Recovering Back to Default Configuration IP address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to the default value, press the hardware-based reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. 2-Port 10/100/1000T 802.3bt PoE + 6-Port 10/100/1000T 802.
802.3bt PoE++ GS-4210-24UP4C Console 2 4 SYS 1 3 PoE Reset PWR 115200, N, 8, 1 6 8 10 12 14 16 18 20 22 24 5 7 9 11 13 15 17 19 21 23 1000 LNK 10/100 LNK ACT ACT bt PoE-in-Use at/af PoE-in-Use 2 4 6 8 10 1 3 5 7 9 Reset Button Figure 5-3: GS-4210-24UP4C Reset Button 4-Port 10/100/1000T 802.3bt PoE + 20-Port 10/100/1000T 802.
6. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq?method=category&c1=1 Support team mail address: support@planet.com.tw GS-4210 802.3bt PoE Series User’s Manual: https://www.planet.com.tw/en/support/download.
