Datasheet

3
GS-4210-16UP4C
GS-4210-24UP4C
– GVRP
• SupportsSpanningTreeProtocol
– STP (Spanning Tree Protocol)
– RSTP (Rapid Spanning Tree Protocol)
– MSTP (Multiple Spanning Tree Protocol)
– STPBPDUGuard,BPDUltering andBPDUforwarding
• Supports LinkAggregation
– IEEE802.3adLinkAggregationControlProtocol(LACP)
– Ciscoether-channel(statictrunk)
• Provides port mirror (many-to-1)
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)
Quality of Service
• Ingress and egress rate limit per port bandwidth control
• Storm control support
– Broadcast/Unknownunicast/Unknownmulticast
• Trafcclassication
– IEEE 802.1p CoS
– TOS/DSCP/IPprecedenceofIPv4/IPv6packets
• Strict priority and Weighted Round Robin (WRR) CoS policies
Multicast
• Supports IPv4 IGMP snooping v2 and v3
• Supports IPv6 MLD snooping v1, v2
• IGMP querier mode support
• IGMPsnoopingportltering
• MLDsnoopingportltering
Security
• Authentication
– IEEE802.1Xport-basednetworkaccessauthentication
– Built-in RADIUS client to cooperate with the RADIUS
servers
– RADIUS/TACACS+ login user access authentication
• Access control list
– IPv4/IPv6 IP-based ACL
– MAC-based ACL
• MAC security
– Static MAC
– MACltering
• PortsecurityforsourceMACaddressentriesltering
• DHCPsnoopingtolterdistrustedDHCPmessages
■95WUPoE/PoH PowerOutputMode
■90W802.3btPoE++PowerOutputMode
■72WUPoE/PoH PowerOutputMode
■60W802.3btPoE++PowerOutputMode
■60WForcePowerOutputMode
■36WEnd-span PoEPowerOutputMode
■36WMid-span PoEPowerOutputMode
Built-in Unique PoE Functions for Powered Devices Management
AsitisthemanagedPoEswitchforsurveillance,wirelessandVoIPnetworks,
the GS-4210-16UP4C and GS-4210-24UP4C feature the following special PoE
managementfunctions:
■PDAliveCheck
■Scheduled PowerRecycling
■PoESchedule
■PoEUsageMonitoring
■PoEExtension
Intelligent Powered Device Alive Check
The GS-4210-16UP4C and GS-4210-24UP4C can be configured to monitor
connectedPDstatusinrealtimeviapingaction.OncethePDstopsworkingand
responding, the GS-4210-16UP4C and GS-4210-24UP4C will resume the PoE port
powerandbringthePDbacktowork.Itwillgreatlyenhancethenetworkreliability
through the PoE port resetting the PD’s power source and reducing administrator
management burden.
PD Alive Check
Restart PoE device if without response
Step 3
Checking alive status for 3 times
Step 2
No Response!
Ping Request
PoE
ON OFF
Restart PoE Device
Step 4
PoE Device Status Good!!
Step 1
Ping Request
Ping Echo
Alarm Notification
Scheduled Power Recycling
The GS-4210-16UP4C and GS-4210-24UP4C allow each of the connected PoE IP
camerasorPoEwirelessaccesspointstorebootataspecifiedtimeeachweek.
Therefore, it will reduce the chance of IP camera or AP crash resulting from buffer
overow.
IP Camera
S M T W T F S
AP Router IP Phone
PoE lighting
Door Phone
Automatically Reboot