PLANET Technology Corp. GRT-101/401/402 User’s Manual G.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Copyright Copyright (C) 2007 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Table of Contents Table of Contents ...........................................................................................3 Chapter 1 Overview .......................................................................................1 SOFTWARE FEATURES ......................................................................1 SOFTWARE SPECIFICATIONS ...........................................................1 ATM Protocol................................
PLANET Technology Corp. GRT-101/401/402 User’s Manual STU-C (CPE) side...............................................................................21 Console Configuration.........................................................................21 3.3.5 Advanced Setup.............................................................................22 SHDSL ................................................................................................22 WAN.....................................................
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.8.4 Bridge ............................................................................................47 3.8.5 Route .............................................................................................47 3.8.6 LAN................................................................................................47 3.8.7 IP share .........................................................................................47 3.8.8 DHCP...............
PLANET Technology Corp. GRT-101/401/402 User’s Manual Chapter 1 Overview Based on digital subscriber line (DSL) technology, PLANET’s G.SHDSL products, GRT series provide an affordable, flexible, efficient Internet access solution for SOHO customers while reducing deployment and operational costs from service providers.
PLANET Technology Corp. GRT-101/401/402 User’s Manual I.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Hardware Specification WAN/LAN Ports RJ-11 SHDSL WAN port x1 10/100Mbps LAN port x1 on GRT-101 10/100Mbps LAN port x4 on GRT-401/GRT-402 Connector RJ-11 connector for WAN, RJ-45 connector for LAN Cabling Requirement G.SHDSL : AWG26 or higher 10 /100 Base T: UTP/STP Category 3 or 5 LEDs SHDSL, Power Status, WAN Link and Action Status, LAN Link/Active (and 100M Status), Alram Speed SHDSL: 64Kbps to 2.304Mbps or 128Kbps to 4.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Chapter 2 Installation 2.1 Front Panel LEDs The LEDs on the front panel indicate the operational status of GRT series.
PLANET Technology Corp.
PLANET Technology Corp. GRT-101/401/402 User’s Manual The STU-R is a standalone and can able to place in desktop. All the external wiring shall be located at the rear panel. The LAN port is a 10 Base-T / 100Base-TX auto-sensing and half/full duplex Ethernet interface and complied with IEEE 802.3 / 802.3u respectively. The console (RS-232C) interface for configuration is menu-driven operation and can also be configured through Ethernet interface by Telnet or Web-based operation.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 2.4 Setting up the hardware environment Step 1: Connect the power adapter to the port labeled DC-IN on the rear panel of the product. Step 2: Connect the Ethernet cable. If GRT-101 is directly connected to PC, the Ethernet cable has to be used cross over one (refer to figure 2-6). If the product is connected to hub or switch, be sure that the hub or switch supporting auto-MDI/MDI-X or not.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Chapter 3 Configuration 3.1 Purpose This chapter provides information about configuring GRT series. Note: After you have completed all necessary setting for GRT series, make sure to write the new configuration to NVRAM by “write” command and reboot the system, or all of your changes will not take effect. 3.2 Logon Procedure There are three methods to logon to GRT series: serial console, Telnet, and web interface.
PLANET Technology Corp. GRT-101/401/402 User’s Manual admin> show system If firmware file is downloaded from our local distributor or FTP server, please refer to TFTP command in the section 3.18 Software Upgrade for more information on how to update GRT series firmware. 3.2.2 Telnet Make sure the correct Ethernet cable is used for connecting the LAN port of your computer to GRT series. The LAN LNK indicator on the front panel shall light if a correct cable is used.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.3 Web operation and Quick Installation Guide 3.3.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Web UI Configuration After connection via web browser, click BRIDGE and CPE Side to setup Bridging mode of GRT series and then click Next for the next setting. 1. Enter WAN1 VPI: 0 and VCI: 32. 2. Select WAN1 AAL5 Encap: LLC 3. Enter LAN IP: 192.168.0.1 4. Enter LAN Sub-net Mask: 255.255.255.0 5. Enter Gateway: 192.168.0.254 The Gateway is directly pointed to the BAS IP. 6. Click Next 7. The screen will prompt the new configured parameters.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Console Configuration Do the following steps: 1 User : admin « password: admin « 2 enable « supervisor password: root « 3 setup « mode « Bridge « 4 wan « Interface number (1~8) : 1 « Protocol « : Ethernet « vpi_vci : 0 « 32 « encap : LLC « 5 bridge « gateway « 192.168.0.254 « 6 lan«address« 192.168.0.1 « 255.255.255.0« 7 (back to root) write « y « y «(reboot) 3.3.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 1. Enter LAN IP: 192.168.0.1 2. Enter LAN Sub-net Mask: 255.255.255.0 3. Host Name: SOHO 4. DHCP Server: Enable 5. Click Next 6. Enter DHCP Client Start IP: 192.168.0.2 7. Enter DHCP Client End IP: 192.168.0.51 8. Enter DNS Server: 192.168.0.1 9. The DNS server is embedded in GRT series. 10. Click Next to write the new setting.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 11. Enter WAN1 VPI: 0 and VCI: 32. 12. Select WAN1 AAL5 Encap: LLC 13. Select: PPPoA + NAT or PPPoE + NAT 14. Click Next 15. Enter user name provided by ISP: user1@net 16. Enter Password provided by ISP: user1 17.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 18. The screen will prompt the new configured parameters. Check the parameters and click Restart, the router will reboot with the new setting or click Continue to configure other parameters. Console Configuration Do the following steps: 1. User : admin « password: admin « 2. enable « supervisor password: root « 3. setup « mode « Route « 4.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.3.3 Routing Mode for IPoA or EoA Web UI Configuration For Route Mode with Classical IP over ATM and Ethernet over ATM, follow the following setting. First select ROUTE and CPE Side, and then click Next for setting others parameters. 1. Enter LAN IP: 192.168.0.1 2. Enter LAN Sub-net Mask: 255.255.255.0 3. Host Name: SOHO 4. DHCP Server: Enable 5.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 6. Enter DHCP Client Start IP: 192.168.0.2 7. Enter DHCP Client End IP: 192.168.0.51 8. Enter DNS Server: 192.168.0.1 9. The DNS server is embedded in GRT series. 10. Click Next to write the new setting. 11. Enter WAN1 VPI: 0 and VCI: 32. 12. Select WAN1 AAL5 Encap: LLC 13. Select: IPoA, IPoA + NAT, EoA, or EoA + NAT 14. Click Next 15. Enter WAN1 IP: 10.1.2.1 16. Enter WAN1 Subnet Mask: 255.255.255.0 17. Enter Default Route Gateway: 10.1.2.2 18.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 19. The screen will prompt the new configured parameters. Check the parameters and click Restart, the router will reboot with the new setting or click Continue to configure other parameters. Console Configuration Do the following steps: 1. User : admin « password: admin « 2. enable « supervisor password: root « 3. setup « mode « Route « 4. wan « Interface number (1~8) : 1 « protocol « IPoA or EoA « address « 10.1.2.1 « 255.255.255.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.3.4 LAN-to-LAN Connection with Bridge Mode Web UI Configuration STU-R (CO) side Click setup to setup the BRIDGE as CO Side. Follow the instruction. 1. Enter WAN1 VPI: 0 and VCI: 32. 2. Select WAN1 AAL5 Encap: LLC 3. Enter LAN IP: 192.168.0.1 4. Enter LAN Sub-net Mask: 255.255.255.0 5. Enter Gateway: 192.168.0.2 6.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 7. Setup the CO Router in bridge mode (refer to bridge mode in section 2.1). The gateway of CO Router is pointed to LAN IP, 192.168.0.2, of CPE Router.
PLANET Technology Corp. GRT-101/401/402 User’s Manual STU-C (CPE) side Follow the above instruction. The only difference in this configuration is that users have to choose CPE SIDE instead of CO SIDE. Setup the CPE Router in bridge mode. The gateway of CPE Router is pointed to LAN IP, 192.168.0.1, of CO Router. Console Configuration Do the following steps in STU-R side: 1. 2. 3. 4. 5. 6.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.3.5 Advanced Setup Advanced configuration contains SHDSL, WAN, Bridge, Route, NAT/DMZ and Virtual server parameters. SHDSL You can setup the Annex type, data rate and SNEXT margin for SHDSL parameters in SHDSL. Click SHDSL Annex Type: There are three Annex types, Annex A, Annex B and Annex AB in SHDSL. Link Type: For GRT-402 only, support two link type, 4-wire mode with 4.608 Mbps data rate and 2-wire mode with 2.304 Mbps data rate.
PLANET Technology Corp. GRT-101/401/402 User’s Manual these parameters in WAN configuration menu. The WAN Number 1 will be the parameters setup in Basic Setup. If you want to setup another PVC, you can configure them in WAN 2 to WAN 8. Please enter the necessary parameters. After inserting the parameters, please press Finish to complete WAN configuration. . The screen will prompt the parameters that will be written in GRT series. Please confirm these parameters before writing in machine.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Press Restart to restart GRT series working with new parameters or press continue to setup another parameter. Bridge The bridge mode can be setup the static bridge parameters. Click Bridge to start Bridge configuration. Press Add to add the static bridge information. The screen will prompt the parameters that will be written in GRT series. Check the parameters before writing in machine.
PLANET Technology Corp. GRT-101/401/402 User’s Manual With Dynamic Routing, you can enable GRT series to automatically adjust to physical changes in the network’s layout. The Cable/DSL Firewall Router, using the RIP protocol, determines the network packets’ route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other routers on the network. Click Route to modify the routing information.
PLANET Technology Corp. GRT-101/401/402 User’s Manual RIP Mode: this parameter determines how the product handle RIP (Routing information protocol). RIP allows it to exchange routing information with other router. If set to Disable, the gateway does not participate in any RIP exchange with other router. If set Enable, GRT series broadcasts the routing table of GRT series on the LAN and incoporates RIP broadcast by other routers into it’s routing table.
PLANET Technology Corp. GRT-101/401/402 User’s Manual NAT/DMZ NAT (Network Address Translation) is the translation of an Internet Protocol address (IP address) used within one network to a different IP address known within another network. One network is designated the inside network and the other is the outside. Typically, a company maps its local inside network addresses to one or more global outside IP addresses and reverse the global IP addresses of incoming packets back into local IP addresses.
PLANET Technology Corp. GRT-101/401/402 User’s Manual addresses (eg: 192.168.0.10 ~ 192.168.0.50) collectively use two of the global IP addresses (eg: 69.210.1.9 and 69.210.1.10). The Multi-NAT table will be setup as; Virtual Start IP Address: 192.168.0.10 Count: 40 Global Start IP Address: 69.210.1.9 Count: 2 Press Finish to continue. The screen will prompt the parameters that will be written in GRT series. Check the parameters before writing in GRT series.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.3.6 Administration This session introduces security and simple network management protocol (SNMP) and time synchronous. Security For system secutiry, suggest to change the default user name and password in the first setup otherwise unauthorized persons can access GRT series and change the parameters. There are three ways to configure GRT series, Web browser, telnet and serial console. Press Security to setup the parameters.
PLANET Technology Corp. GRT-101/401/402 User’s Manual SNMP Simple Network Management Protocol (SNMP) is the protocol not only governing network management, but also the monitoring of network devices and their functions. GRT series can generate SNMP traps to indicate alarm conditions, and it relies on SNMP community strings to implement SNMP security. This gateway support MIB II. Click SNMP to configure the parameters. In the table of current community pool, you can setup the access authority.
PLANET Technology Corp. GRT-101/401/402 User’s Manual access right. After configuring the community pool, press OK. Click Modify to modify the trap host pool. Version: select version for trap host. IP: type the trap host IP Community: type the community password. Press OK to finish the setup. The browser will prompt the configured parameters and check it before writing into GRT series. Press Restart to restart the gateway working with the new parameters and press Continue to setup other parameters.
PLANET Technology Corp. GRT-101/401/402 User’s Manual the Internet. SNTP can be used when the ultimate performance of the full NTP implementation. For SNTP, select SNTP v4.0. SNTP service: Enable Time Server: All of the time server around the world can be used but suggest to use the time server nearby. Time Zone: you have to choose the right time zone. Press Finish to finish the setup. The browser will prompt the configured parameters and check it before writing into GRT series.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Upgrade You can upgrade the gateway using the upgrade function. Press Upgrade. Browse the file and press OK button to upgrade. The system will reboot automatically after finishing. Restart For restarting GRT series, click the Restart in UTILITY menu. Press Restart to reboot GRT series. 3.3.7 Status You can monitor the SHDSL status including mode, Tx power and Bitrate and Performance information including SNR margin, atteunation and CRC error count.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.4 Command Line Interface For serial console and Telnet management, GRT series implements two operational interfaces: command line interface (CLI) and menu driven interface. The CLI mode provides users a simple interface, which is better for working with script file. The menu driven interface is a user-friendly interface to general operations. The command syntax for CLI is the same as that of the menu driven interface.
PLANET Technology Corp. GRT-101/401/402 User’s Manual interfaces have on-line help information. To get on-line help, type “?” for CLI mode or press CTRL+Q for menu driven interface. 3.4.1 Multi-level password protection When you login via serial console or Telnet, GRT series defaults to a program execution (read-only) privileges to you. To change the configuration and write changes to nonvolatile RAM (NVRAM), you must work in enable mode.
PLANET Technology Corp. GRT-101/401/402 User’s Manual interface. Note: See section 3.14 User Profile for more information on how to add, delete, modify, and list user profile. 3.4.2 Menu Driven Command Line Interface Before applying any changes into machine, it is suggested to ensure the modifications, and operations in GRT series’ CLI menu driven configurations. Following table is the main CLI menu.
PLANET Technology Corp.
PLANET Technology Corp.
PLANET Technology Corp.
PLANET Technology Corp. GRT-101/401/402 User’s Manual To start machine configuration, please move the cursor “ >>” to enable and press enter key. GRT series will prompt for password for enable mode, insert the supervisor password. (Default supervisor password is root.) . ---------------------------------------------------------------------Command: enable Message: Please input the following information.
PLANET Technology Corp. reboot ping admin utility exit GRT-101/401/402 User’s Manual Reset and boot system Packet internet groper command Setup management features TFTP upgrade utility Quit system 3.4.4 Status You can view running system status of SHDSL, WAN, route and interface via status command. Move cursor “ >> “ to status and press enter. >> shdsl wan route interface Show SHDSL status Show WAN interface status Show routing table Show interface statistics status 3.4.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.4.7 Reboot To reboot GRT series, use reboot command. Move cursor to “ >> “ to write and press enter. --------------------------------------------------------------------Command: reboot Message: Please input the following information. Do you want to reboot? (y/n): y --------------------------------------------------------------------- 3.4.8 Ping Ping command will be used to test the connection of router.
PLANET Technology Corp. GRT-101/401/402 User’s Manual profile table however users who have the supervisor password can change the configuration of GRT series. Move the cursor “ >> “ to user and press enter key. >> clear modify list Clear user profile Modify the user profile List the user profile You can delete the user by number using clear command. If you do not make sure the number of user, you can use list command to check it.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.5.5 SNTP Time synchronization is an essential element for any business that relies on an IT system. The reason for this is that these systems all have clocks that are the source of time for files or operations they handle. Without time synchronization, time on these systems varies with each other or with the correct time and this can cause- virtual server schedule processes to fail and system log exposures with wrong data.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.8 Setup All of the setup parameters are located in the subdirectories of setup. Move the cursor “ >> “ to setup and press enter.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 4-wire product can be worked under 2-wire mode. You can setup the data rate by the multiple of 64Kbps- n is from 0 to 32. If you configure n is 0, the product will perform as adaptive mode. There are two types of SHDSL Annex type, Annex-A and Annex-B. Clear command can clear CRC error count. Generally, you cannot need to change SNR margin, which range is from 0 to 10. 3.8.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.8.4 Bridge You can setup the bridge parameters in bridge command. If the product is configured as a router, you do not want to setup the bridge parameters. Move the cursor “ >> “ to bridge and press enter. >> gateway static Default gateway Static bridging table You can setup default gateway IP via gateway command. You can setup 20 sets of static bridge in static command. 3.8.5 Route You can setup the routing parameters in route command.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.8.8 DHCP >> generic fixed list Configure generic DHCP parameter Configure fixed host IP address list Show DHCP configuration For more DHCP information, review DHCP server section. 3.8.9 DNS proxy You can setup three DNS servers in the product. The number 2 and 3 DNS servers are option. Move cursor “ >> “ to dns_proxy and press enter.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.9 Connection Mode GRT series supports two connection modes: bridging and routing. Currently, it comes pre-configured with routing mode. Note that, routing mode and bridging mode cannot be used simultaneously.
PLANET Technology Corp. GRT-101/401/402 User’s Manual set up GRT series for bridging management with IP = 192.168.0.1, subnet mask = 255.255.255.0, and gateway IP = 192.168.0.254: admin# setup lan 1 address 192.168.0.1 255.255.255.0 admin# setup bridge gateway 192.168.0.254 The IP address should be an IP address on the same network as that of the “far-end” station. The gateway IP address should be the IP address of the far-end station that is used to route the LAN packets.
PLANET Technology Corp.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.11.2 Static routing table In order to pass data through a network and onto the Internet or WAN, you might need to add the IP addresses of gateways to the static routing table. Follow the instructions below to build a static routing table manually by adding or deleting entries in the table. For example, to add a route to network address 140.182.1.0 with subnet mask of 255.255.255.0 via gateway at 140.182.2.254: admin# setup route static add 140.182.1.
PLANET Technology Corp. GRT-101/401/402 User’s Manual admin# write 3.11.3 NAT/PAT NAT can be used to share an Internet connection, to reduce the requirement for publicly assigned IP addresses, to expand an existing network without affecting existing IP based account schemes, and to hide an internal network schema from public networks. It is often used in the situation where only one IP address could be assigned for the network, such as a PPP connection to an local ISP, e.g.
PLANET Technology Corp. GRT-101/401/402 User’s Manual possible when the number of hosts having concurrent requests to the external network is equal to or less than the number of external IP addresses on GRT series. To setup GRT series working for the above situation where WAN 1 is used to connect to the corresponding ISP, use the below commands: admin# setup lan 1 attrib Virtual admin# setup ip_share nat global interface 3 1 admin# setup ip_share nat global range 3 69.210.1.
PLANET Technology Corp. GRT-101/401/402 User’s Manual To show the configuration, use the list command: admin# setup ip_share nat fixed list Note: The maximum number of entries in the NAT fixed IP address mapping pool is 128. To save your changes, enter: admin# write Another function provided by this GRT series NAT/PAT is the virtual server mapping. Specific ports on the WAN interface (e.g., WAN 1) are re-mapped to services inside the LAN. As only 69.210.1.8 (e.g.
PLANET Technology Corp. GRT-101/401/402 User’s Manual admin# write 3.11.4 DHCP server The DHCP server application automatically assigns IP addresses to DHCP clients. Follow the steps below to enable the DHCP applications. The example sets a DHCP server, which could service 50 DHCP clients. The available IP addresses for DHCP clients are located from 192.168.0.2 to 192.168.0.51. In this example, the LAN environment is configured with gateway of 192.168.0.1 and subnet mask of 255.255.255.0.
PLANET Technology Corp. GRT-101/401/402 User’s Manual addresses of real DNS servers: admin# setup dns_proxy 168.95.1.1 168.95.192.1 140.92.61.55 Note: For PPP connections, GRT series will get DNS server IPs from ISP and assign them into DNS proxy automatically if they have been pre-configured by the local ISP. The maximum number of DNS servers is limited to 3. To save your changes, enter: admin# write 3.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Only GRT-402 support 4 wire phone line to connect, it also allow to assign link type by actually connection type.
PLANET Technology Corp. GRT-101/401/402 User’s Manual LLC header of the packet. The VC based multiplexing method carries each protocol on a separate ATM virtual circuit. This method is sometimes used in private networks, in which PVC creation is very economical. Note: Each VC is expressed as WAN x, where x is a number between 1 and 8. GRT series comes pre-configured with one ATM VC (WAN 1 with VPI/VCI = 0/32) already established.
PLANET Technology Corp. GRT-101/401/402 User’s Manual WAN 6 Disable WAN 7 Disable WAN 8 Disable To save the new WAN port configuration, enter: admin# write 3.12.3 ATM traffic shaping The objectives of ATM traffic management are to deliver quality-of-service (QoS) guarantees for the multimedia applications and provide overall optimization of network resources. Currently, GRT series supports two kinds of ATM QoS service: constant bit rate (CBR) and unspecified bit rate (UBR).
PLANET Technology Corp. GRT-101/401/402 User’s Manual WAN 8 Disable To save the new WAN port configuration, enter: admin# write 3.12.4 WAN IP address Note: This sub-section is for routing mode operation with protocol of “Ethernet” and/or “IPoA” only. For PPP connections, it is unnecessary to set the WAN port IP address and subnet mask. To set the WAN 3 with IP address of 192.168.3.3 and subnet mask of 255.255.255.0, follow the following example: admin# setup wan 3 address 192.168.3.3 255.255.255.
PLANET Technology Corp. GRT-101/401/402 User’s Manual If your local ISP uses protocols of “PPPoA” or “PPPoE” over the ATM VC, you may need to setup the username and password information provided from your local ISP. The maximum length of username and password for ISP setting is limited to 51. The following command configures the ISP profile for WAN 3 with username “pppoa3@isp.com”, password “Fuyg47ds”, and idle timeout of 10 minutes: admin# setup wan 3 isp pppoa3@isp.
PLANET Technology Corp. GRT-101/401/402 User’s Manual PPPoA/PPPoE protocols must work with NAT/PAT. Please refer to section 3.11.3 NAT/PAT for details. 3.13 System Status and Performance Use the “status” command to display GRT series activities.
PLANET Technology Corp. GRT-101/401/402 User’s Manual ----- --------------- --------------- --- ----- ------ -------- -----WAN1 192.168. 1. 1/255.255.255. 0 0/ 32 LLC IPoA Yes To list active route status currently, type: admin# status route Flag Destination / Netmask / Gateway Interface Portname ---- ------------------------------------------ ------------ --------S 0.0.0.0/ 0.0.0.0/ 200.0.8.254 200.0.8.1 C 200.0.8.0/ 255.255.255.0/ directly 200.0.8.1 C 192.168.0.0/ 255.255.255.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Note: You must perform the above procedure in the sequence as shown. To show all user profiles with attributes, type: admin# admin user list Legal access user profile No User Name UI Mode ---- ------------------ ----------1 titan 2 test 3 (Empty) 4 (Empty) 5 (Empty) Command Menu To delete user profile 2, enter: admin# admin user clear 2 To save your changes, enter: admin# write 3.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Configuration generic parameter Telnet listening TCP port : 47 To save your changes, enter: admin# write 3.15.2 Legal client IP You could assign the legal client IP addresses such that only Telnet clients and web browsers at the legal client IP addresses can access GRT series. The following example specifies a legal IP address 192.168.0.6 in the pool. admin# admin security ip_pool modify 1 192.168.0.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Note: GRT series comes pre-configured without any constraint on the legal access IP addresses of Telnet clients and web browsers for convenience. However, it is very important to setup management security to prevent invalid access to GRT series from Internet. 3.
PLANET Technology Corp. GRT-101/401/402 User’s Manual 3.16.2 SNMP trap GRT series can generate alarm conditions to SNMP manager via SNMP traps. The following example configures trap 1 with SNMPv2c encapsulation. The SNMP manager is located at 192.168.0.254 with community “private”. admin# admin snmp trap 1 edit 2 192.168.0.
PLANET Technology Corp. GRT-101/401/402 User’s Manual setup mode Route setup shdsl mode STU-R setup shdsl n*64 0 setup shdsl type Annex_A setup shdsl margin 0 setup wan 1 protocol IPoA setup wan 1 address 192.168.1.1 255.255.255.0 setup wan 1 vpi_vci 0 32 setup wan 1 encap LLC setup wan 1 qos class UBR setup wan 1 qos pcr 2400 setup wan 1 isp test test 10 ... admin snmp trap 3 edit Disable 192.168.0.254 private admin snmp trap 4 edit Disable 192.168.0.254 private admin snmp trap 5 edit Disable 192.168.0.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Watch the system messages to ensure every command was accepted by the system successfully. Note: The Telnet program is recommended during backup process. If only the serial port could be used, carefully add some delay by adjust the line and/or character delay for your terminal access program so that all command could be accepted by the system without error.
PLANET Technology Corp. GRT-101/401/402 User’s Manual Download Byte Transferred : 624641 bytes Complete Transfer Complete, Replace Now? (y/n): y Writing flash....................... OK! Do you want to reboot? (y/n): y Be sure to write the new image to NVRAM and immediately reboot the device to activate it. When you log back onto GRT series after the reboot, then you can use the “show system” command to verify the version of the new firmware that is active, and restore your configuration.
