User's Manual FT-902 FT-902S15 FT-902S35 FT-902S50 FT-905A FT-906A20 / FT-906B20 10/100Base-TX to 100Base-FX Managed Media Converter
Trademarks Copyright © PLANET Technology Corp. 2010. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
TABLE OF CONTENTS 1. INTRODUCTION .............................................................................................................1 1.1 PACKAGE CONTENTS .................................................................................................................................. 1 1.2 HOW TO USE THIS MANUAL ........................................................................................................................ 1 1.3 ABOUT THE MANAGED MEDIA CONVERTER .........................
4.6 QUALITY OF SERVICE ................................................................................................................................ 38 4.7 OAM SETUP ............................................................................................................................................ 41 4.7.1 Local TS-1000 OAM Setup ............................................................................................................................... 41 4.7.2 Remote TS-1000 OAM Setup .......
1. INTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: ● Managed Fast Ethernet Media Converter x1 ● CD-ROM User's Manual x1 ● Quick Installation Guide x1 ● External DC 5V / 2A Power Adapter x 1 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
1.3 About the Managed Media Converter The Managed Media Converter FT-90X provide conversion between 10/100Base-TX and 100Base-FX network. There are SC / LC / WDM connectors and single-mode / multi-mode media for your needs. Ethernet signal that allows two type segments connect easily, efficiently and inexpensively. This Managed Media Converter can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis (MC-700, MC-1500 and MC-1500R).
■ Application Fiber-optic Networking for ISP, enterprise, and home With high performance of data transmission and easy installation, the Managed Media Converter can build an ISP network solution of FTTH (Fiber to the Home) or FTTC (Fiber to the Curb) for ISPs and FTTB (Fiber to the Building) for small office network environment from enterprises. The Web Management helps network administrators to monitor and setup the converter, speed and duplex through web browsers.
1.4 Product Features Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3u 100Base-FX standard One-channel media conversion between 10/100Base-TX and 100Base-FX TP port supports 10/100Base-TX auto-negotiation and auto-MDI/MDI-X 100Base-FX: 50/125μm or 62.
1.5 PRODUCT SPECIFICATION Model FT-902 FT-902S15 FT-902S35 FT-902S50 FT-905A FT-906A20 FT-906B20 Hardware Specification 1 x 10/100Base-TX port Ports 1 x 100Base-FX port Copper Interface RJ-45 port (Auto-MDI/MDI-X) Twisted Pair Optic Interface SC Optic Wavelength 1300nm 1310nm SFP 1310nm 1310nm - WDM TX:1310 TX:1550 RX:1550 RX:1310 Launch Max. -14 -7 -5 -0 - -8 Power(dBm) Min. -19.0 -20 -9 -5 - -14 -34.
2. HARDWARE DESCRIPTION This product provides two different running speeds – 10Mbps, 100Mbps in the same Managed Media Converter and automatically distinguishes the speed of incoming connection. This section describes the functionalities of FT-90X’s components and guides how to install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.
2.1.1 LED Indicators LED Color Description PWR Green Lit: When +5VDC power detected. Fiber LNK/ACT Green TP LNK/ACT Green TP 100 Green #Notice: Lit: To indicate the link through that fiber port is successfully established. Blink: Indicate that the Fiber port is actively sending or receiving data over that port. Lit: To indicate the link through that port is successfully established. Blink: Indicate that the port is actively sending or receiving data over that port.
2.2 Install the Converter This section describes how to install your Managed Media Converter and make connections to the Managed Media Converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of Managed Media Converter do not need software configuration. To install your Managed Media Converter on a desktop or shelf, simply complete the following steps. 2.2.
#Notice: Please refers to APPENDIX-A for detailed wiring information of the Managed Media Converter. To prevent from optic acceptor malfunction, check the both wires / transmitter before power on the converter. FT-905A Installation FT-905A is with high reliability and flexibility to extend the distance from 2km to 60km. It depends on the MFB family Fast Ethernet SFP modules. The SFP transceivers are hot-plug and hot-swappable.
2.2.2 Chassis Installation and Rack Mounting To install the Managed Media Converter in a 10-inch or 19-inch with standard rack, follow the instructions described below. Step 1: Place your Managed Media Converter on a hard flat surface, with the front panel positioned towards your front side. Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis.
Figure 2-6 Mounting the Chassis in a Rack -8-
3. MEDIA CONVERTER MANAGEMENT This chapter describes how to manage the Managed Media Converter. Topics include: - Overview - Management methods - Assigning an IP address to the Managed Media Converter - Logging on to the Managed Media Converter 3.1 Overview This chapter gives an overview of Managed Media Converter management. The FT-90X provides a simply WEB browser interface.
3.2.1 Web Management The PLANET Managed Media Converter provides a built-in browser interface. You can manage the Managed Media Converter remotely by having a remote host with Web browser, such as Microsoft Internet Explorer, Mozilla Firefox, Google Chrome or Apple Safari.
3.2.3 PLANET Smart Discovery Utility For easily list the Managed Media Converter in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual CD-ROM is an ideal solution. The following install instructions guiding you for run the Planet Smart Discovery Utility. 1. Deposit the Planet Smart Discovery Utility in administrator PC. 2. Run this utility and the following screen appears.
3. This utility show all necessary information from the devices, such as MAC Address, Device Name, firmware version, Device IP Subnet address, also can assign new password, IP Subnet address and description for the devices. 4. After setup completed, press “Update Device”, “Update Multi” or “Update All” button to take affect. The meaning of the 3 buttons above are shown as below: Update Device: use current setting on one single device. Update Multi: use current setting on choose multi-devices.
4. WEB MANAGEMENT The FT-90X Managed Media Converter provide Web interface for management function configuration and make the Managed Media Converter operate more effectively - They can be configured through the Web Browser. A network administrator can manage and monitor the Managed Media Converter from the local LAN. This section indicates how to configure the Managed Media Converter to enable its management function. 4.
4.2 System 4.2.1 System Information The System Information Web page provides information for the current device. System Information Web page helps network administrator to identify the firmware versions, IP Subnet Address and etc. The screen in Figure 4-2 appears and Table 4-1 describes the System Information object of Managed Media Converter.
4.2.2 IP Configuration The IP Configuration includes the DHCP Client, IP Address, Subnet Mask, Gateway and Description. The screen in Figure 4-3 appears and Table 4-2 describes the IP Configuration object of Managed Media Converter. Figure 4-3 IP Configuration Web page screen The IP Configuration Web page screen includes the following configurable data: DHCP Client Allow disable or enable the DHCP Client function of the Managed Media Converter, the factory default mode is Disable.
4.2.3 Password Setting This function provides administrator to secure Web login. The screen in Figure 4-4 & 4-5 appears and Table 4-3 describes the Password Setting object of Managed Media Converter.
The Password Setting Web page includes the following configurable data: Login Name Displays the user name (admin). Old Password Enter the old password is required before entering the new password. New Password Specifies the new password. The password is not displayed. As it entered an “y” corresponding to each character is displayed in the field. (The maximum length is 16 characters) Confirm This confirms the new password.
Press “Browser” button to find the firmware location administrator PC, The screen in Figure 4-7 appears Figure 4-7 Firmware Upgrade Web page screen After find the firmware location from administrator PC, press “Upgrade” button to start the firmware upgrade process. The screen in Figure 4-8 & 4-9 appears.
Figure 4-9 Firmware Upgrade Web page screen When firmware upgrade process is completed then the following screen appears, please click “here” to re-login the Managed Media Converter with latest firmware and the screen in Figure 4-10 & 4-11 appears.
Figure 4-11 Login Web page screen -20-
4.2.5 SNMP Management This function provides SNMP Management and SNMP Trap Receiver Configuration function of the Managed Media Converter and the screen in Figure 4-12 & 4-13 appears and Table 4-4 & 4-5 describes the SNMP Management and SNMP Trap Receiver object of Managed Media Converter. Figure 4-12 SNMP Management Web page screen The SNMP Management Web page includes the following configurable data: SNMP Agent Allow disable or enable the SNMP Agent function, the default mode is “Disable”.
Figure 4-13 SNMP Trap Receiver Configuration Web page screen The SNMP Trap Receiver Configuration Web page includes the following configurable data: SNMP Trap Allow disable or enable the SNMP Trap function, the default mode is “Disable”. SNMP Trap Destination Allow input the IP address of SNMP Trap Destination. Trap Event Apply button Cold Start When Managed Media Converter executes Cold Start operation, the administrator PC (SNMP Trap Destination) will receive a Cold Start Trap.
4.2.6 Factory Default This function provides Factory Default function of the Managed Media Converter and the screen in Figure 4-14 & 4-15 & 4-16 appears.
Figure 4-16 Login Web page screen 4.2.7 System Reboot This function provides System Reboot function of the Managed Media Converter and the screen in Figure 4-17 & 4-18 & 4-19 appears.
Figure 4-18 System Reboot Web page screen Figure 4-19 Login Web page screen -25-
4.3 Port Management 4.3.1 Port Configuration This function allows displaying TP / Fiber port status. The Link Status in the screen displays the current connection speed and duplex mode; else this function will show red “Down” when the TP / Fiber port is disconnected. Press the “Refresh” button to renew the screen. The screen in Figure 4-20 appears and Table 4-6 describes the Port Configuration object of Managed Media Converter.
Default mode: Disable Ingress Rate Limit The value of inbound traffic limitation in kilobit-per-second (kbps). The available options are : • No Limit • 512K • 1M • 2M • 4M • 8M • 10M • 50M Default mode: No Limit The Ingress Rate Limit configuration field as show in Figure 4-21. Egress Shaping The value of outbound traffic limitation in kilobit-per-second (kbps).
Figure 4-22 Port Configuration-Egress Shaping Web Page screen 4.3.2 Port Status This function allows displaying TP / Fiber port detail status, such as Link Status, Duplex Mode, Flow control, Speed and Auto negotiation. Press the “Refresh” button to renew the screen, the screen in Figure 4-23 appears and Table 4-7 describes the Port Status object of Managed Media Converter.
The Port Status Web page includes the following configurable data: Port Indicate the TP port and Fiber port. Link Status Displays the current link status of TP and Fiber port. Duplex Mode Displays the current duplex mode of TP and Fiber port. Flow Control Displays the current Flow Control status of TP and Fiber port. Speed Displays the current speed mode of TP and Fiber port. Auto Negotiation Displays the current Auto negotiation status of TP and Fiber port.
Figure 4-25 Port Statistics Web Page screen 4.4 Converter Configuration This function provides useful setting for the Managed Media Converter, such as Maximum Packet length, Loop detection, storm control and etc. The screen in Figure 4-26 appears and Table 4-8 describes the Converter Configuration object of Managed Media Converter.
The Converter Configuration Web page includes the following configurable data: Maximum Packet Length Provide maximum packet length setting for the Managed Media Converter, the available options are 1518 bytes, 2048 bytes and 16K bytes. Default mode is 16K bytes. Loop Detection Provide Disable or enable the Loop detection function. Default mode is Disable. Loop Status Displays the Loop Detection status. Broadcast Storm Control Provide Disable or enable the Broadcast Storm Control function.
4.5 VLAN A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a converter is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all the network devices are still plug into the same switch physically. The Managed Media Converter supports IEEE 802.
802.1Q Tag User Priority 3 bits TPID (Tag Protocol Identifier) Destination Address Source Address 6 bytes 1 bits 12 bits 2 bytes Ethernet Type VLAN TAG 6 bytes VLAN ID (VID) TCI (Tag Control Information) 2 bytes Preamble CFI 4 bytes 2 bytes Data FCS 46-1517 bytes 4 bytes The Ether Type and VLAN ID are inserted after the MAC source address, but before the original Ether Type/Length or Logical Link Control.
Default VLANs The Managed Media Converter initially configures one VLAN, VID = 1, called "default." The factory default setting assigns all ports on the Managed Media Converter to the "default". As new VLAN are configured in Port-based mode, their respective member ports are removed from the "default." 4.5.1 VLAN Group This function allows disable or enable the IEEE 802.1Q VLAN operation mode. Press the “Apply” button to save the current configuration of Managed Media Converter.
Figure 4-28 VLAN Group Web Page screen The VLAN Group Web page includes the following configurable data: VLAN Mode Provide Disable or enable the IEEE 802.1Q VLAN operation mode. Default mode is Disable. Management VLAN Group Provide define the Management VLAN group. Default mode is VLAN1. VLAN Group Indicate the VLAN Group from 1 to 16. VID Provide define the VLAN Group ID and the available options are 1 to 4094. Member Apply button TP Provide assign TP port into VLAN Groups.
4.5.2 VLAN Per Port Setting This function provides IEEE 802.1Q VLAN per port setting for TP and Fiber port of Managed Media Converter. Press the “Apply” button to save the current configuration of Managed Media Converter. The screen in Figure 4-29 appears and Table 4-10 describes the VLAN Per Port Setting object of Managed Media Converter.
4.5.3 Q-in-Q VLAN Setting When enable Q-in-Q function, Managed Media Converter can insert or remove 4-bytes Q-in-Q tag in the received 802.3 frames after SA. User can define Q-in-Q tag value freely. And in default condition, Q-in-Q tag format is same as VLAN tag. In normal application, enable two port’s Q-in-Q function. UTP Port set to insert QinQ tag and Fiber port set to remove Q-in-Q Tag.
4.6 Quality of Service Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic. QoS enables you to assign various grades of network service to different types of traffic, such as multi-media, video, protocol-specific, time critical, and file-backup traffic. QoS reduces bandwidth limitations, delay, loss, and jitter.
The Quality of Service Web page includes the following configurable data: Qos Mode Provide 4 different QoS mode for operation, the available options are: Disable 802.1p Tag Priority The 802.1p Tag Priority field as show in Figure 4-32. IP Address Priority The IP Address Priority field as show in Figure 4-33. IP DSCP Priority The IP DSCP Priority field as show in Figure 4-34. Default mode is Disable.
Figure 4-33 IP Address Priority Web Page screen Figure 4-34 IP DSCP Priority Web Page screen -40-
4.7 OAM Setup 4.7.1 Local TS-1000 OAM Setup This function provides Local TS-1000 OAM Setup of Managed Media Converter. Press the “Apply” button to save the current configuration of Managed Media Converter. The screen in Figure 4-35 appears and Table 4-13 describes the Local TS-1000 OAM Setup object of Managed Media Converter.
4.7.2 Remote TS-1000 OAM Setup The Remote TS-1000 OAM Setup is an advanced remote device monitor feature that allows you to Remote monitor and automatic notify status indication. Remote monitor 1. User instructs center Media Converter to issue a status notification request frame defined in TS-1000 to get status of terminal Media Converter. 2. Terminal Media Converter receives the status notification request frame and sends out status response frame, which carries its current status.
Figure 4-37 GT-90X Remote TS-1000 OAM Setup Web Page screen #Notice: Please use the PLANET FT-90Xv2 or GT-80X and GT-90X as the Remote device. 4.7.3 TS-1000 Loop Back Test The TS-1000 Loop Back Test allows manual run this loop back test to check the interconnection between two Media Converter devices. To assure the Remote TS-1000 OAM function can work correctly.
In-band and out-band Loop back 1. Instruct center Media Converter to issue an OAM frame to request a loop back test. Terminal return start response OAM frame to center Media Converter. 2. Terminal Media Converter runs at loop back mode. 3. Central Media Converter send test frame and terminal Media Converter loop back the frames. Test frame can be generated from central Media Converter’s UTP port (Out-Band) or from central Media Converter (In-Band) automatically. 4.
TS-1000 Loop Back Test Result Result Display the TS-1000 Loop Back Test Result. Fail or Pass. Result counter Display the value of Counter Result. Table 4-14 Descriptions of the TS-1000 Loop Back Test Web Page Screen Objects #Notice: Please use the PLANET FT-90Xv2 or GT-80X and GT-90X as the Remote device. 4.7.4 802.3ah Setup When enable 802.3ah OAM function, all 802.3ah OAMPDU packets will trap to embedded CPU. Software will implement auto discovery procedure.
The 802.3ah Setup Web page includes the following configurable data: 802.3ah OAM State Provide disable or enable the 802.3ah OAM State function. Default mode is Enable. 802.3ah OAM Mode Allow to choose “Active” or “Passive” for 802.3ah OAM Mode. Default mode is Passive. Loopback Reply Provide disable or enable the Loopback Reply function. Default mode is Enable. Remote OAM Configure Provide disable or enable the Remote OAM Configure function. Default mode is Enable.
Figure 4-40 802.3ah Loop Back Test Web Page screen The 802.3ah Loop Back Test Web page includes the following configurable data: 802.3ah Loop Back Test Send Packet Number Allow input the number for packet send and the available options is 1 to 255. Default is 16. Packet Length (Not include CRC) Allow input the number for Packet Length and the available options is 60 to 1514. Default is 60. Apply button Press this button for save current configuration of Managed Media Converter.
4.8 Security This function provides TCP / UDP Filter setting of Managed Media Converter. Press the “Apply” button to save the current configuration of Managed Media Converter. The screen in Figure 4-41 appears and Table 4-17 describes the TCP / UDP Filter setting object of Managed Media Converter.
4.9 Logout This function provides Logout function of Managed Media Converter, when the “Are you sure to logout” pop window appears; press the “OK” button to logout Web page of Managed Media Converter. The screen in Figure 4-42 & 4-43 appears.
5. TROUBLESHOOTING This chapter contains information to help you solve problems. If the media converter is not functioning properly, make sure the media converter was set up according to instructions in this manual. The Link LED is not lit Solution: 1. Check the cable connection and remove duplex mode of the Managed Media Converter. 2. Check the port configuration of the link partner; make sure the two side devices with the same link configuration.
APPENDIX A NETWORKING CONNECTION A.1 Device‘s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment MDI MDI-X Contact Media Dependant Interface Media Dependant Interface -Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 Not used 6 Rx - (receive) 7, 8 Tx - (transmit) Not used A.
Crossover Cable 1 1 2 2 3 3 4 4 5 6 5 6 SIDE 1 7 7 8 8 SIDE 1 SIDE 2 SIDE2 1 = White / Orange 1 = White / Green 2 = Orange 2 = Green 3 = White / Green 3 = White / Orange 4 = Blue 4 = Blue 5 = White / Blue 5 = White / Blue 6 = Green 6 = Orange 7 = White / Brown 7 = White / Brown 8 = Brown 8 = Brown Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into
A.4 Power Information The power jack of Managed Media Converter is with 2.5mm in the central post and required +5VDC power input. It will conform to the bundled AC-DC adapter and Planet’s Media Chassis. Should you have the problem to make the power connection, please contact your local sales representative. Please keep the AC-DC adapter as spare parts when your Managed Media Converter is installed to a Media Chassis. 2.5mm DC Receptacle 2.5mm +5V for each slot DC receptacle is 2.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number * Produced by: Manufacturer‘s Name Manufacturer‘s Address :Web Smart 10/100Base-TX to 100Base-FX Media Converter : FT-902_905A_902S15_902S35_902S50 : : Planet Technology Corp. 11F, No. 96, Min Chuan Road, Hsin Tien Taipei, Taiwan , R. O.C.
EC Declaration of Conformity For the following equipment: *Type of Product : Web Smart 10/100Base-TX to 100Base-FX WDM Media Converter - Tx: 1550) - 20KM *Model Number : FT-906A20_B20 * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 11F, No. 96, Min Chuan Road, Hsin Tien Taipei, Taiwan , R. O.C.
