FT-80x Series (V4) User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
8. Cable Connection Parameter
Cables:
Standard
(Wavelength)
100BASE-FX
(1310nm)
1000BASE-SX
(850nm)
1000BASE-LX
(1310nm)
Fiber Type & Cable
Specication
Multi-mode
50/125μmor
62.5/125μm
Single-mode 9/125μm
FT-80x:
The wiring details are shown below:
Wiring distance:
Duplex Connection Limitation (max.)
Twisted Pair
Half/Full
Node to Node
Node to Switch/Hub
100 meters
Multi-Mode Converters
MM Half
Node to Node
Node to Switch
412 meters
MM Full
Node to Node
Node to Switch
2 kilometers
Single-Mode Converters*
(FT-80xynn; x= 2, 6; y= S, A, B; nn=km)
SM Full
Node to Node
Node to Switch
Depending on model
Copper
Connector
10/100Mbps RJ45
Copper Modes Full duplex, auto-negotiation
Packet
Forwarding
Rate (64bytes)
14880pps @10Mbps/
148810pps @100Mbps
DIP Switch LFP Disable/Enable; FX Full-/Half-duplex
Protocols and
Standards
IEEE 802.3, 10BASE-T
IEEE 802.3u, 100BASE-TX, 100BASE-FX
Dimensions 94 x 70 x 26mm (W x D x H)
Weight 0.2kg
Power 5V DC, 2A max.
Emission FCC, CE
Temperature Operating: 0 ~ 50°C/Storage: -40 ~ 70°C
Humidity 5% ~ 95% non-condensing
Installation Wall mount, DIN-rail, Chassis installation
Note
1. Please note FT-806A20 and FT-806B20 are designed
to work together. It means you must connect FT-
806A20 to FT-806B20 in pair. If both ends are FT-
806A20 or FT-806B20, or any of the above models
to any 3rd-party device, they can’t work normally
and may damage the fiber connectors.
2. The FT-802xxx/FT-806xxx single mode media
converter series provides long distance support from
15 km to 50km. When shorter distance of single-
mode fiber cable is used, you might need to insert
an in-line optical attenuator in the link to avoid
overloading of the receiver.
GT-80x:
Wiring Distances:
Standard Fiber
Diameter
(micron)
Bandwidth
(MHz x km)
Max. Distance
(meters)
1000BASE-SX MM
62.5
50
100
500
220
550
1000BASE-LX
MM
62.5
50
5
5
550
SM 9 N/A 5000*
Note
The single-mode port (1000BASE-LX port) of GT-802S,
GT-802S40, GT-802S60, GT-805A, GT-806A15/B15,
GT-806A40/B40 and GT-806A60/B60 is complied with
LX 5 kilometers and provides an additional margin
allowing for a 10/15/20/40/60/80/120 kilometers
Gigabit Ethernet link on single mode fiber.
9.ProductSpecications
FT-80x
Model
FT-
801
FT-
802
FT-
802S15
FT-
802S35
FT-
802S50
FT-806A20
FT-806B20
Fiber
Connector
ST SC SC SC WDM
Fiber Mode Multi-mode Single-mode
Fiber Maximum
Distance
2km 15km 35km 50km 20km
Note
3. For connection to the Fast Ethernet products, please
refer to the device’s Technical Manual.
4. Consult your dealer for DIN-rail or Chassis
installation.
GT-80x
Model GT-802 GT-802S GT-802S40 GT-802S60
Fiber Connector SC-type connector
Fiber Mode Multi-mode
Single
mode
Single
mode
Single
mode
Fiber Maximum
Distance
220m/550m 20km 40km 60km
Copper
Connector
10/100/1000Mbps RJ45
Copper Modes Full duplex, auto-negotiation
Packet
Forwarding
Rate (64bytes)
14880pps @10Mbps/
148810pps @100Mbps/
1488000pps @1000Mbps
DIP Switch LFP Disable/Enable
Protocols and
Standards:
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3z 1000BASE-SX/LX
Jumbo Packet
Size
9K
Dimensions 94 x 70 x 26mm (W x D x H)
Power 5V DC, 2A max.
Emission FCC CE
Temperature Operating: 0 ~ 50°C/Storage: -10 ~ 70°C
Humidity 5% ~ 95% non-condensing
Installation Wall mount, DIN-rail, chassis installation
Model GT-805A
GT-806A15
GT-806B15
GT-806A40
GT-806B40
GT-806A60
GT-806B60
Fiber Connector
SFP, LC
type
SC-type connector (WDM)
Fiber Mode
May vary
on module
Single mode
Fiber Maximum
Distance
May vary
on module
20km 40km 60km
Copper
Connector
10/100/1000Mbps RJ45
Copper Modes Full duplex, auto-negotiation
Packet
Forwarding
Rate (64bytes)
14880pps @10Mbps
148810pps @100Mbps
1488000pps @1000Mbps
DIP Switch LFP Disable/Enable
Protocols and
Standards
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/100BASE-FX
(GT-805A SFP slot only, auto detection)
IEEE 802.3ab 1000BASE-T
IEEE 802.3z 1000BASE-SX/LX
Jumbo Packet
Size
9K
Dimensions 94 x 70 x 26mm (W x D x H)
Power 5V DC, 2A max.
Emission FCC CE
Temperature Operating: 0 ~ 50°C/Storage: -10 ~ 70°C
Humidity 5% ~ 95% non-condensing
Installation Wall mount, DIN-rail, chassis installation
Note
1. Please note GT-806A15/806B15 and GT-806A60/
806B60 are designed to work together. It means
you must connect GT-806A15 to GT-806B15 or
GT-806A60 to GT-806B60 in pairs. If both ends
are GT-806A15 or GT-806A60 and GT-806B15 or
GT-806B60, or any above model to any 3rd-party
device, they can’t work normally and may damage
the fiber connectors.
2. The GT-802S/GT-806xxx single mode media
converter series provides long distance support from
20 km to 60km. When shorter distance of single-
mode fiber cable is used, you might need to insert
an in-line optical attenuator in the link to avoid
overloading the receiver.
3. For connection to the Gigabit Ethernet products,
please refer to the device’s technical manual.
4. Consult your dealer for DIN-rail or chassis
installation.