User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Step 3: Connect your FSD-604HP to network devices.
A. Connect one end of a standard network cable to
the Port-5~6 of the FSD-604HP that marks with
“Uplink”.
B. Connect the other end of the cable to the network
devices such as routers, Ethernet switches or NVRs
(network video recorders).
Step 4: Connect your FSD-604HP to PoE PDs.
A. Connect one end of a standard network cable to
one of the four 10/100Mbps RJ45 PoE+ ports of
the FSD-604HP.
B. Connect the other end of the cable to the 802.3af/
at PD.
Office Building Office Area
Warehouse
Control Room
Office Building
FSD-604HP
DC
Power Line (DC)
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3at
PoE IP Camera
Fixed IP Dome
IEEE 802.3af PoE Splitter
DC
IEEE 802.3af
PoE IP Camera
PoE Extender
PoE
PoE
PoE
PoE
Wall-mount Installation
Step 1: Please nd the wall that can mount the FSD-604HP.
Step 2: Please refer to the picture below and screw the two
screws on the wall.
122mm
Step 3: Hang the FSD-604HP on the screws from the wall.
Step 4: Repeat step 5 of Desktop Installation for power
supply to the FSD-604HP.
Note
Before mounting the device to the wall, please
check the location of the electrical outlet and the
length of the Ethernet cable.
Note
Cable distance for Switch
If the “DIP Switch Mode” is set to
“Standard”, then the distance between the
FSD-604HP and PC/PD should not exceed 100
meters for UTP/STP cable.
If the “DIP Switch Mode” is set to “Extend”,
then the distance between the FSD-604HP and
PC/PD should not exceed 250 meters.
Note
Make sure the wiring is correct
Category 3/4/5 cable can be used in 10 Mbps
operation. To reliably operate your network at
100Mbps, you must use an unshielded twisted-pair
(UTP) Category 5/5e cable, or better data grade
cabling. While a Category 3 or 4 cable may initially
seem to work, it will soon cause data loss.
Step 5: Supply power to the FSD-604HP.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the Switch receives power, the power LED should remain
solid orange.
7.ProductSpecications
Model
FSD-604HP
4-Port 10/100Mbps 802.3at PoE + 2-Port
10/100Mbps Desktop Switch
Hardware Specications
Network Connector
6-Port RJ45 for 10/100BASE-TX, auto MDI/
MDIX
PoE Inject Port
4-Port with 802.3af/at PoE injector function
(Port 1 to port 4)
LED Display
System: Power (Orange)
Per PoE port: PoE (Orange, port 1 to port 4)
LNK/ACT (Green, port 1 to port 6)
DIP Switch
Distance in Standard mode is 100M
Distance in Extend mode is 250M
Based on the cable category
Switch Architecture Store and Forward switch architecture
MAC Address Table
2K MAC address table with auto learning
function
ESD Protection 6KV
Switch Fabric 1.2Gbps
Switch Throughput 0.89Mpps @64bytes
Maximum Packet Size 1536bytes
Flow Control
Back pressure for half duplex. IEEE 802.3x
pause frame for full duplex
Power Requirements AC 100~240V, 2A max.
Power Consumption Max. 63 watts, 214 BTU
Dimensions (W
x D x H) 168 x 93 x 32mm
Weight 499g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power Supply Type End-span
Power Pin Assignment 1/2 (+), 3/6 (-)
PoE Power Output
Per Port 52V DC, 300mA. max. 15.4 watts
(IEEE 802.3af)
Per Port 52V DC, 600mA. max. 30 watts
(IEEE 802.3at)
PoE Power Budget 60 watts
Number of PDs
(7
watts)
4
Number of PDs
(15.4 watts)
4
Number of PDs
(30 watts)
2
Standard Conformance
EMI Safety CE, FCC
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus
Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-condensing
Storage Humidity 5 ~ 95%, relative humidity, non-condensing
8. Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET Website rst to check if it
could solve your issue. If you need more support information,
please contact PLANET support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php?type1=1
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2019.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.