0/100 Mbps Direct Attached Print Server FPS-1101 User’s Manual 1
Copyright (C) 2006 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
TABLE OF CONTENTS INTRODUCTION............................................................................................................................................................... 5 PRODUCT OVERVIEW ...................................................................................................................................................... 5 COMPONENTS AND FEATURES ..............................................................................................................................
GENERAL TROUBLESHOOTING OVERVIEW.................................................................................................................... 66 POWER RELATED PROBLEMS........................................................................................................................................ 66 PRINT PORT RELATED PROBLEMS ................................................................................................................................
Introduction Product Overview The external print servers enhance capability by letting you place your printers at convenient locations directly on the Ethernet network, and by increasing network printer performance and management. Please note that the print server does not support printing with host-based printers, e.g. CAPT, GDI, and PPA. Network Management The print servers support the Simple Network Management Protocol (SNMP), which remote printer management and a warning.
LED Indicators LED State Blinking for POST Status (Yellow) 100Mbps On (Green) 10Mbps On (Yellow) Indication When power switched on, the Status indicator will flash five times, and then on. LAN Port has a valid network connection at 100Mbps. LAN Port has a valid network connection at 10Mbps.
To printer Reset Button Network Environment Wired Network with Print Server: Printer Print Server HUB Computer Computer 7 Computer
2. Print Server Installation Preparation To meet users’ network printing needs in today’s heterogeneous and multiple protocol networking environments, the print server supports industrial standard protocols, including TCP/IP, IPX/SPX, NetBEUI and AppleTalk. This means that the print server supports the most popular network operating systems today, including NetWare, Windows 95/98/Me/NT/2000/XP/2003, UNIX systems and Macintosh computer.
Windows Printing via the internet to Allows saving distribution of HQ NT/2000/XP/2003 Internet Printing Protocol- hardcopy document over Internet, replacing fax, mail enabled print server Comment Configuration solution Table has many installations way to setup Windows 95/98/Me, Windows NT/2000/XP/2003, NetWare, UNIX / Linux system and Mac computer. Firstly, we introduce PSAdmin utility, HP Web JetAdmin program and Internet Printing Protocol solution.
3. Software Installation The PSAdmin is a proprietary Windows-based management program that can assist you in configuring and managing your print server in NetWare environments. The program can be installed from the setup CD of print server. Installing the PSAdmin and Print Server’s Driver 1. To enable network communication with print server, your computer must have a proper IP address, e.g. 192.168.0.100 (the print server’s default IP is 192.168.0.10) 2.
3. Click Next, the wizard will automatically discover the print server. 4. From the Select A Print Sever screen, select the print server that you want to configure and click Next. 5.
Click No if you want the print server to keep using the default IP address and keep the default settings: z IP address: 192.168.0.10 z Subnet Mask: 255.255.255.0 Click Yes if you want change IP address to the print server, and then click Next. Note: The IP address of print server must be within the same subnet as your network adapter. 6. In the setup wizard, select an already configured printer from the list, click Next, Next and then Finish to complete the installation.
7. Click Add New Printer to launch Windows Add Printer Wizard. 8. Click Next and select Local Printer, make sure the Automatically detect and install my Plug and Play printer check box is NOT checked. Then click Next.
9. Make sure the Use the following port radio-button is clicked and select LPT1: (recommended Printer Port) from the pull-down list. Then click Next. 10. Select Manufacturer and Printer from the lists of printer’s driver. Then click Next.
11. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the printer and choose whether you want to make it your default printer. Then click Next. 12. Then, choose whether you want to share the printer with other network user, print a test page (please select No.), etc. Select the appropriate radio-button and click Next and Finish. 13.
15. Right-click, select Properties -> Ports and verify that the print server’s port appears. 16. Go to General; click Print Test Page to verify the configuration. 17. Done.
If you want to install more print servers, start setup wizard from your Windows Start menu: start -> All Programs -> Network Print Server -> PSWizard and repeat the installation procedure. Using PSAdmin After the software of setup CD is successfully installed, starts PSAdmin utility from your Windows Start menu: start -> All Programs -> Network Print Server -> PSAdmin. The screen will then appear as follow picture.
TCP/IP Wizard 1. Click Wizard button just like a picture ＜ ＞.and select TCP/IP Wizard. 2 Select “Obtain an IP address from DHCP server”. If there is a DHCP server on your network. This option allows the print server to obtain IP-related settings automatically from your DHCP server. This setting, by default, is disabled. If you would like to manually specify an IP address to the device, please skip to the following step. 3 In the IP Address option, type an IP address for the print server.
7 Done NetWare Wizard 1. Log into your NetWare file server as a Supervisor (Admin.) or equivalent. 2. Click Wizard button just like a picture ＜ picture. ＞.and select NetWare Wizard, as follow 3. Select the NetWare File Server to which the print server device will be attached. 4. Type in a Print server. 5. Type in a Print Queue Names. Note: Each print queue corresponds to each print port of the print server. 6. Click OK. 7. Done. 8.
3. Select the print server that you wish to configure. 4. Click Properties in the tool bar and the following screen will appear, Properties button just like a picture ＜ ＞, as follow picture. 5. Select NetWare and type in the Print server that created during PCONSOLE. 6. (Optional) In Bindery Settings, Select NetWare file server(s) that print server can do Bindery mode. 7. (Optional) In NDS Settings, Select NetWare file server(s), NetWare 4.x or later that print server can do NDS mode. 8. Click OK.
Obtain an IP address from a DHCP server: This option enables or disables the DHCP feature of the print server. When this option is enabled, the print server will obtain an IP address automatically from the DHCP server on your LAN. The default value is “Disable”. Note: 1. Once this option is enabled, the following IP address, Subnet Mask, Gateway will be grayed out and are not available for editing. 2.
Upgrade Upgrade allows the user to upgrade the print server device. In order to upgrade the unit please perform the steps as follows: 1. Click Upgrade button just like a picture ＜ ＞, as shown as follow picture 2. Select General Upgrade. Make sure that the upgrade file is located in the same directory as PSAdmin. Reset 1. Click Reset button just like a picture ＜ ＞. 2. Reset allows the user to reset the print server device in order to establish a new connection or for new settings to take effect.
Note: Configure the print speed in the Advanced label, must match the printer’s speed which connect to the print server. Undependable configuration will cause printer to abnormal printing. Multiple Print Queues Configuration To configure the print server to service multiple print queues, please follow the instructions listed below: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Log into your NetWare file server as a Supervisor (Admin.) or equivalent. Run the PSAdmin from your Windows.
3. Click Change or Remove Programs tab. 4. Select Network Print Monitor for Windows 95/98/NT/2000/XP/2003 and click Change/Remove button. 5. The un-installation wizard program will be launched. 6. Follow the directions on the screen to complete the un-installation procedure.
4.Internet Printer Connection and HP Web JetAdmin IPP Overview Print server(s) support the Internet Printing Protocol (IPP). Using the appropriate software on your system, you can create an IPP print path from your system as Windows PC over the Internet. Note: For incoming print path requests, the network administrator have to configure the firewall to accept incoming IPP requests.
6. In URL’s box, input print server’s IP address, for example, http://192.168.10.182/lp1. Then Click Next. ** One port should be the port name as lp1. 7. It will check print server to connect to HP printer, if not, it will appear as follow picture. Then Click OK. 8. Select the appropriate printer manufacturer and printer type and click “Next”, appear as follow picture. 9. If you want your Windows-based programs to use this printer as the default printer, please select “Yes”, and Click Next.
10. Click Finish button. 11. Done. HP Web JetAdmin Overview HP Web JetAdmin allows you to use a Web browse to revise, view, manage and diagnose devices connected to the print server or any standard printer MIB devices. For more information about a procedure or Windows in the HP Web JetAdmin software, see about HP’s relation document. System Requirements HP Web JetAdmin software runs on Microsoft Windows NT, HP-UX, Solaris, Red Hat Linux and SuSE Linux system.
Download the installation files from HP Customer Care Online at http://www.hp.com/go/webjetadmin/. Follow the instructions on the screen to install the HP Web JetAdmin software. Note: Installation instructions are also contained in the HP Web JetAdmin install file. Confirming Installation and Supply Access ․Confirming that the HP Web JetAdmin software is correctly installed by navigating to it with your browser as shown in the following.
5. Configuration from Embedded Web Server Overview The Print Server contains an embedded web server that can be accessed through a supported web browser on a LAN, for example, IE 4.0, Netscape 4.0 or above is recommended. The embedded web server provides access to configuration and management pages for the print server and the connected peripheral device. Using Embedded Web Server Before you can use the embedded web server, the print server must be configured with an IP address.
Print Server Name: This option allows you to view device name of the print server. To correct the print server’s device name. System Contact: This option allows you to view contact name of the print server. To check the print server’s contact name who in charge of this device. System Location: This option allows you to view Location name of the print server. To confirm the print server’s location name where the print server is located in the office’s LAN.
Printer Status 1.Click Status, it then appears the sub-menu. 2.Click Printer, it then as shown in the following picture. Manufacturer: This option allows you to view manufacturer of the printer. When the printer connected with the print server, it will be show in the manufacture box. Model Number: This option allows you to view model of the printer. When the printer connected with the print server, it will be show in the model box.
Use DHCP/BOOTP: This option allows you to view DHCP/ BOOTP status. If there is a DHCP/BOOTP server on your network, this option allows the print server to obtain IP-related settings automatically from your DHCP server. IP Address: This option allows you to view IP address from the print server. The IP address must meet the IP addressing requirements of the network segment. (default: 192.168.0.10) Subnet Mask: This option allows you to view subnet mask from the print server.
General Settings: Print Server Name: This option allows you to view print server’s name would be configured by PSAdmin utility. Polling Time: This option allows you to view polling time from the print server. This function is search for NetWare Server by per time. NetWare NDS Setting: Use NDS Mode: Enable or Disable. Name of the NDS Tree. Name of the NDS Context. Current Status: Connect or Disconnect. NetWare Bindery Setting: Use Bindery Mode: Enable or Disable.
AppleTalk Status 1.Click Status, it then appears the sub-menu. 2.Click AppleTalk, it then as shown in the following picture. AppleTalk Settings: If no any zone exists, the print server itself displays the zone name as an asterisk (*) in the current AppleTalk Status of the print server in the web browser. Port Name: -xxxxxx-1, where xxxxxx represents the last six digits of the print server’s Node ID. Printer Type: This option allows you to view printer type from the print server.
SNMP Communities: This option allows you to view SNMP communities from the print server. There are two communities that control message from the network management of the print server. SNMP Traps: This option allows you to view SNMP traps from the print server. SMB Status 3.Click Status, it then appears the sub-menu. 4.Click SMB, it then as shown in the following picture. Workgroup Name: This option allows you to view the SMB Workgroup Name from the print server.
Shared Name: This option allows you to view the Shared Name from the print server. Setup Menu Meanwhile, you have finished the IP address configuration with print server. You should use web browser to configure the print server. The setup menu of the print server helps administrator to setup the print server’s System, Printer, NetWare, TCP/IP, SNMP and AppleTalk. Preparation Enter the IP address of the print server as the URL, default: 192.168.0.10.
Email Alert: This option allows you to Enable/Disable the Email Alert support. SMTP Server IP Address: This option allows you to input the IP address of your Email SMTP server. Administrator E-mail Address: This option allows you to input your Email address that you want to receive the notification by Email. Print Server Name: This option allows you to input device name of the print server. To correct the print server’s device name.
TCP/IP Setup: 3. Click Setup, it then appears the sub-menu. 4. Click TCP/IP, it then as shown in the following picture. DHCP/BOOTP: This option allows you to select DHCP/ BOOTP option. If there is a DHCP/BOOTP server on your network. This option allows the print server to obtain IP-related settings automatically from your DHCP server. IP Address: This option allows you to input IP address from the print server. The IP address must meet the IP addressing requirements of the network segment.
NetWare Setup 1.Log into your NetWare file server as a Supervisor (Admin.) or equivalent. 2. Select NetWare and type in the Print server that created during PCONSOLE Select the NetWare File Server to which the print server device will be attached. 3.Click Setup, it then appears the sub-menu. 4.Click NetWare, it then as shown in the following picture. Print Server Name: This option allows you to input print server name which configured by PSAdmin utility or PCOMSOLE program.
Logon Password: This option allows you to input encrypted password from the print server. The print server login to NetWare server that administrator set password from selected print server. Use NDS Mode: To Enable NDS Mode, if you want to setup NDS environment. To select Tree Name of NetWare then input context name in the Context box. Bindery Mode: To Enable Bindery Mode, if you want to setup Bindery environment. To select File Server Name of NetWare. Installing Print Server on NetWare 4.x/5.
4. Add or Modify the “SET BINDERY CONTEXT =” line to include the NDS organization (O) and all organization unit (OU) objects where users are located. For example: SET BINDERY CONTEXT = O=ABC; OU=SALES.OU=ABC-USA.O=ABC; OU=TECH.OU=ABC-USA.O=ABC ; 5. When done, save the new AUTOEXEC.NCF file. Please restart your NetWare file server in order for new settings to take effect immediately. 6. Next, please refer to “Auto Setup” section in this chapter to finish installing your print server. 7.
3. 4. Zone Name: In this option, type an AppleTalk Zone name that you want the print server to belong to or leave it in default (This enables the print server automatically search and link itself to the default zone that is set on the AppleTalk router, if found). We also assume that at least an AppleTalk Zone exists on the network. If no any zone exists, the print server itself displays the zone name as an asterisk (*) in the current AppleTalk Status of the print server in the web browser.
Note: If you select a Zone that the PRINT SERVER doesn’t belong to, as you specified in the previous section, no print server will be displayed in the Step 4. 3. If you are using a PostScript printer you can select the LaserWriter 8 icon. 4. The Chooser window then displays PRINT SERVER (s) featuring the support for AppleTalk protocol, along with its default Chooser Name in the right-hand Select A PostScript Printer dialog box. Note: 1.
When an unusual condition or activity occurs, the SNMP agent alerts the SNMP manager through SNMP traps. Following list summaries SNMP trap messages that the print server will send out. Activities/SNMP Trap Messages Description Link Up or Link Down When the network interface on the print server fails, a link down trap message is generated; if the network interface comes back to life, a link up trap message is sent.
SNMP Community: The print server supports up to two community names. The default community name is public (case-sensitive), with Read Only access right in default. Support HP WebJetAdmin: This option allows user determine to disable/enable the Support HP WebJetAdmin. SNMP Traps: Enable the function of sending SNMP Authentication Failure trap message to the network administrator, if the community name within a SNMP request is not correct.
3. Workgroup Name: This option allows you to assign a workgroup name to print server on the Network Neighborhood. Windows uses it to identify the print server on the Network. 4. Shared Name: This option allows you to assign a name to print server’s port.
6. Network Print Monitor Preparation The print server supports TCP/IP, IPX/SPX and NetBEUI protocols under Windows 95/98/Me. Please make sure that the following steps have been completed before proceeding with installation under Windows PC. Select A Desired Protocol TCP/IP The TCP/IP Protocol must be installed. For further information, please read “TCP/IP Protocol Installation” section in this chapter.
TCP/IP Protocol Installation 1. Click Start, point to Settings and select Control Panel. 2. Double click the Network icon. 3. If the TCP/IP Protocol is not already installed, click Add. 4. Select Protocol and click Add. 5. Select Microsoft from the Manufacturers list. 6. Select TCP/IP Protocol from the Network Protocols list. 7. Specify an IP address, Subnet Mask, and Gateway address or specific “Obtain IP address automatically”, if a DHCP server is available on the LAN. 8. Restart the computer. 9. Done.
NetBEUI Protocol Installation 1. Click Start, point to Settings, and select Control Panel. 2. Double click the Network icon. 3. If the NetBEUI is not already installed, click Add. 4. Select Protocol and click Add. 5. Select Microsoft from the Manufacturers list. 6. Select NetBEUI from the Network Protocols box and follow the instructions on the screen. 7. Restart your computer for new settings to take effect. 8. Done.
10. A message reading, “After your printer is installed, Windows can print a test page so you can confirm that the printer is set up properly.” Select No and click Finish. 11. Double-click the newly created Printer Name icon. 12. Select Printer and Properties. 13. Click Details tab and select Add Port. 14. In the Add Port dialog box, select Other, as shown in the following picture. 15. Select the Network Print Port and click OK. 16.
By default, the computer will first search for the print server(s) on the network by using the IPX/SPX protocol. If the IPX/SPX protocol is installed, the print server will be displayed along with its Node ID, as shown in Node column. (The last 6 digits of the Node ID, located on the back of the print server unit). Select one of the print server’s ports from the list. If the IPX/SPX protocol is not installed, no print server will be shown in the display box.
7. TCP/IP LPR Port Printing Installation Basic TCP/IP Installation Overview When installing your print server in a TCP/IP environment, IP addresses are essential as a basic means of communications. It is therefore necessary to first assign an IP address to your print server unit. After assigning an IP address, the print server can be configured accordingly.
5. From the Printer Ports box as shown in the following picture, select the LPR Port. 6. The Add LPR compatible printers box will then appear as shown in the following picture. Type in the IP address assigned to the print server in the Name or address of server providing lpd box. 7. In the Name of printer or print queue on that server box, type in a printer name, for example, lp1. Click OK. 8. In the Printer Ports box, select Close. 9. Click Next. 10.
Windows 2000/XP/2003 Standard TCP/IP Port Printing Installation 1. Click Start, point to Settings, and select Printer. 2. Run Add Printer, Click Next. 3. The Add Printer Wizard screen will appear, Select Local Printer and click Next. 4. From the type of Create a new port box as shown in the following picture, select the Standard TCP/IP Port, Click Next and Next. 5.
6. In the Add Standard TCP/IP Printer Port Wizard box as shown in the following picture, Select Custom, Click Settings button, and click Next. 7. In the Configure Standard TCP/IP Port Monitor box as shown in the following picture, select LPR form Protocol, type in a queue name, for example, lp1. 8. Click OK, and Next. Note: Please DO NOT type any other name than lp1 in this step. 9. Click Finish.
10. Select the appropriate printer manufacturer and printer type list and click Next. 11. Type in a new Printer name or leave it in default, and click Next button. 12. A message reading, “To confirm that the printer is installed properly, you can print a test page”. Select Yes (Recommended) and click Finish. 13. Done.
UNIX Installation After the static IP address is assigned, the Print Server is ready to be configured. For some UNIX/Linux systems, we include the detailed installation procedures below. If you can’t find the installation procedure corresponding to your UNIX system, please refer to your UNIX manuals for details about configuring your UNIX for the “remote printing system”. SCO UNIX 8.0.0 (Caldera Open Unix 8.0.0) 1. Select “SCO Admin”. 2. Select “Printer Setup Manager”. 3.
Basically, the Linux's printing system is based on BSD system. Although many commercial Linux systems are available in the market and their commands will vary slightly, depending upon which version is used, the functionality of the Linux-based variants is exactly the same. Following are the outlined procedures (recommended for all users) on Red Hat Linux 7.2/7.3 or later with X-Window system installed. 1.
7. Click Forward button. 8. In the Name field, type a user-defined name, click Forward.
9. In the Queue Type field, choose Networked UNIX. 10. In the Server field, type the IP address of print server 11. In the Queue field, type a print server’s port name, which connect to the printer. For example: lp1. 12. Click Forward button. 13. In the Printer field, choose Postscript Printer. 14. Choose the model of printer and click Forward.
15. Done.
8.Upgrading Print Server Overview Upgrading print server will allow you to upgrade its firmware inside the print server while the newer software version of the print server is available from your local dealer. Depending on the different systems users might use, this chapter is divided into several Sections; please refer to the following lists for your systems. 1. Upgrading the print server from PSAdmin 2. Upgrading the print server from Windows NT/2000/XP/2003 3.
3. Wait for the transfer successful message. 4. Done. Upgrading the print server from UNIX (Through TCP/IP) 1. Log in as root 2. Ensure binary file is located in your current working directory. 3. Type “tftp ”. 4. At tftp prompt, type “get upgrade”. 5. Change to binary mode. 6. At tftp prompt, type “put mpsXX.bin”. 7. Wait for the file transfer to complete. 8. Quit from tftp. 9. Done. Upgrading the print server from Browser 1.
4. Click Browse… and select the firmware file. 5. Click Upgrade. 6. Done.
9. Troubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in this chapter. If a problem still exists after reading this chapter, please contact your dealer for technical support. LED Light Indicators The print server is equipped with LED lights to assist in diagnosing problems that are the result of the network and/or the print server hardware itself.
Windows 95/98/Me/NT/2000/XP/2003 Troubleshooting Multi-Segment LAN Environment Installation (through the Network Print Port) If your print server and Windows 95/98/Me/NT/2000/XP/2003 are located on two different segments, and your Windows NT server is used as the router/gateway you will need to implement the following procedures in order for your print server to function properly: Add the RIP for NWLink IPX/SPX compatible transport.
Moving the print server to A New Segment If the print server is moved from one network segment to another after the initial installation, through the Network Print Port, the print server must be reconfigured on the original Windows NT server or on each Windows 95/98 computer using this print server in order for the print server’s driver on each computer to re-establish a new connection. Print Server Reconfiguration Procedure on Windows 95/98/Me 1. Click Start on the bottom left hand corner of the screen.
Moving Your Computer to A New Segment If you are using the print server through the Network Print Port on your NT or Windows 95/98/Me computer and your computer is going to be moved onto another segment, you have to reconfigure the print server on your computer to use your print server. However, this situation is like moving the print server to a new segment. Please refer to the “Moving the print server to a new segment” section for more detailed reconfiguration instructions.
If this is the case, please consult your network administrator to obtain an unused IP address for your print server. C. The print server is on one segment and your Windows NT server is on the other segment. (This troubleshooting guide will also apply to a multiple-segmented network while installing the print server) For example, assuming the print server is on Segment A, NT server is on Segment B, and there is a gateway computer between Segment A and Segment B.
6. In your editor, modify "BoxIPAddress" field from "0.0.0.0" to "192.72.214.100". Leave other options as default and do not change their values. When done, save this new file and quit from your editor. Please note, in this step you must specify an IP address which is valid on Segment B, such as 192.72.214.100 in this example, rather than 192.72.214.68. 7. Type, for example, "tftp 192.72.214.68 put config.txt" to save this new configuration back to print server. 8.
Appendix: Rendezvous with Mac OS X 10.3.7 1. Enable the Rendezvous settings from the print server’s WEB configuration. 2. Click "Printer Setup Utility” from the bottom toolbox of Mac.
3. Click "Add".
4. Choose "Rendezvous", and then Mac OS will automatically search the print server on the network. 5. Choose the proper printer model that connected to print server, and then click "Add".
6. Now the network printer with Rendezvous has been successfully installed. SMB Printing with Windows XP 1. Enable the SMB settings from the print server’s WEB configuration. Assume your computers use the “WORKGROUP” as the SMB workgroup name in Windows. Please assign the same SMB name to your print server. If print server uses the different SMB name from computers’, the SMB printing won’t active.
2. Now you can find the print server from the SMB workgroup of Windows. Then, double click it. 3. Double click it again.
4. Now you have to install the printer’s driver. 5. Choose it from the “Add Printer Wizard”.
6. Install printer successfully. 7. Now, you can find your printer’s icon and you can use the SMB printing mode.
Reset Button Reboot the Print server: 1. Verify the power of print server is turned on. 2. Press the reset button once, and then release it. WARNING: This will restart the print server and stop all on-going and pending print jobs! Perform a Factory Default: 1. 2. 3. 4. 5. Disconnect the external power adapter. Hold down the reset button. Reconnect the external power adapter. Wait about 5 seconds. Release the reset button. The print server will restart.
To printer Reset Button 80
Frequently Asked Questions Question A Print jobs are sent to the print queue successfully, but fail to be sent to the printer. Possible explanations 1. The Print server Name/Print Queue configuration in PCONSOLE is incorrect. 2. The Print server name specified and stored in the print server memory doesn’t match the same one set in PCONSOLE. 3. The network cable or power adapter connected to the print server is loose or disconnected. 4. The printer is off-line, jammed or out of paper. Solutions 1. 2. 3. 4.
Question D The Status LED light keeps blinking after POST. Possible explanation and solution The last upgrade process was not completed. The print server must be upgraded again by using the PSAdmin. Please see Chapter 3 for details. Question E The PSAdmin reports “Create Print server Error”, “Create Printer Error”, or “Create Print Queue Error” while using Auto Setup.
Additional Installation Instructions Panasonic KX-P6100/6300/6500 If you are using a Panasonic KX-P6100/6300/6500 laser printer with the print server through the Network Print Port under Windows 95/98, please redirect the printer named “Panasonic KX-P6100 PCL” or “Panasonic KX-P6300 PCL”, or “Panasonic KX-P6500 PCL” to the print server through the Network Print Port. DO NOT redirect the printer named “Panasonic KX-P6100 GDI”, “Panasonic KX-P6300 GDI”, or “Panasonic KX-P6500 GDI” to the print server.
