24-Port 10/100TX 802.
Copyright Copyright © 2019 by PLANET Technology Corp. All rights reserved. No part of this publication may be re-produced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications.
Table Of Contents 1. Introduction................................................................................................ 5 1.1 Package Contents................................................................................. 5 1.2 Product Description............................................................................... 6 1.3 Features.............................................................................................. 6 1.4 Specifications...........................................
1. Introduction 1.1 Package Contents Thank you for purchasing PLANET 24-port 10/100TX 802.3at PoE + 1-port Gigabit TP/SFP combo Ethernet Switch, FGSW-2511P. Unless specified, “PoE+ Switch” mentioned in this user’s manual refers to the FGSW-2511P. Open the box of the PoE+ Switch and carefully unpack it.
1.2 Product Description The FGSW-2511P, a new member in the PLANET 802.3at PoE+ Fast Ethernet Switch family, provides 24 10/100BASE-TX 802.3at Power over Ethernet Plus ports with a total of 190 watts of PoE budget, one 10/100/1000BASE-T uplink port, and one shared 1000BASE-X SFP slot. Its PoE power is more than enough for those network applications that need Fast Ethernet transmission. The FGSW-2511P also offers a simple, cost-effective and non-blocking wire-speed performance.
zz Integrates address look-up engine, supporting 16K absolute MAC addresses zz Automatic address learning and address aging zz Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing Hardware zz 19-inch rack-mount size, 1U height zz LED indicators for PoE ready/activity and LINK/ACT zz Internal AC power supply zz Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az) 1.
Power Requirements AC 100~240V, 3A max. Power Consumption 205 watts, 699.5 BTU Dimensions (W x D x H) 440 x 200 x 45 mm Weight 1220 g ESD Protection Contact discharge of ±6KV DC Air discharge of ±8KV DC Surge Immunity ±4KV Power over Ethernet PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE PoE Power Supply Type Mid-span Power Pin Assignment 4/5 (+), 7/8(-) PoE Power Output Per Port 52V DC, 600mA. max. 30 watts (IEEE 802.3at) Per Port 52V DC, 300mA. max. 15.4 watts (IEEE 802.
2. Hardware Description This section describes the hardware features of the FGSW-2511P. For easier management and control of the FGSW-2511P, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the FGSW-2511P, please read this chapter carefully. 2.
2.1.1 Multiple Functions of DIP Switch The front panel of FGSW-2511P provides one DIP switch for Standard, QoS, VLAN and Extend mode se-lections. The detailed descriptions are shown in the following table. DIP Switch Mode Extend VLAN 1 Standard QoS Extend VLAN 2 Standard QoS Function This mode makes the FGSW-2511P operate as a general switch and all PoE ports operate at 10/100Mbps autonegotiation. All ports can communicate with one another.
Standard Mode (default) Extend VLAN PoE IP Camera Standard QoS PoE Power FGSW-2511P 100 meters (328 feet) 100BASE-TX UTP with PoE PoE VLAN Isolation Mode NVR PoE IP Camera PoE Extend VLAN Port 25 to Ports 1~24 Access Permitted Standard QoS IP Camera Ports 1 to 24 Access Denied PoE IP Camera FGSW-2511P PC PoE 100BASE-TX UTP with PoE 1000BASE-T UTP Extend Mode Extend VLAN PoE IP Camera Standard QoS PoE Power FGSW-2511P Ports 1 to 8 250 meters (820 feet) PoE 10BASE-T UTP with PoE 11
2.1.2 LED Indicators System LED Color PWR Green Function Lights to indicate that the PoE+ Switch has power. Per 10/100BASE-TX PoE+ Port LED Color Function LNK/ACT Green Lights to indicate the PoE+ Switch is successfully connecting to the network at 10/100Mbps. Blinks to indicate that the Switch is actively sending or receiving data over that port. PoE-in-use Amber Lights to indicate the port is providing 52V DC in-line power.
3. Hardware Installation Start up Please refer to the following for your cabling: 10/100BASE-TX All 10/100BASE-TX ports come with Auto-Negotiation capability. They automatically support 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100 BASE-TX ports, and then turn on the FGSW2511P. The port will automatically run at 10Mbps, 20Mbps, 100Mbps or 200Mbps after negotiating with the connected device.
3.1 Rack Mounting To install the FGSW-2511P in a 19-inch standard rack, follow the instructions described below. Step 1: Place your FGSW-2511P on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the FGSW-2511P with supplied screws attached to the package. Figure 3-1 shows how to attach brackets to one side of the FGSW-2511P. 24-Port FGSW-2511 P 10/100X 802.
Step 5: After the brackets are attached to the FGSW-2511P, use suitable screws to securely attach the brackets to the rack, as shown in Figure 3-2. 24-Port FGSW-2511 P 10/100X 802.
3.2 Desktop Installation To install the FGSW-2511P on desktop, simply follow the following steps: Step 1: Attach the rubber feet to the recessed areas on the bottom of the FGSW2511P, as shown in Figure 3-3. 24-Port FGSW-2511 P 10/100X 802.
4. Troubleshooting This chapter contains information to help you solve issues. If the FGSW-2511P is not functioning properly, make sure the FGSW-2511P was set up according to instructions in this manual. Q1: The Link LED is not lit. Solution: Check the cable connection and also try to swap one new cable. Q2: 100BASE-TX port link LED is lit, but the traffic is irregular. Solution: Make sure the attached device is not set to full duplex. Some devices use a physical or software switch to change duplex modes.
Appendix A - 10/100Mbps, 10/100BASE-TX When connecting the Switch to another Fast Ethernet switch, a straight-through or crossover cable might be necessary. Each port of the Switch supports auto-MDI/ MDI-X detection, meaning you can directly connect the Switch to any Ethernet devices without making a crossover cable.
There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
