User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 16-/24-Port 10/100TX 802.3at PoE
+ 2-Port 10/100/1000T + 1-Port shared 1000X SFP Desktop Switch,
FGSD-1821P or FGSD-2621P. “802.3at PoE+ Switch” mentioned in this
Guide refers to the FGSD-1821P or FGSD-2621P
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The
box should contain the following items
The 802.3at PoE+ Switch x 1 User’s Manual x 1 Power Cord x 1
SFP Dust Cap
x 1
Screws x 8
Rack-mounting
Brackets x 2
Rubber Feet x 4
If any of these pieces are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
 Per 10/100BASE-TX Port
LED Color Function
10/100
LNK/ACT
Green
Lights to indicate the link through that
port is successfully established.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
PoE in Use Amber
Lights to indicate the port is providing
PoE DC in-line power.
 Per 10/100/1000BASE-T Port
LED Color Function
10/100/1000
LNK/ACT
Green
Lights to indicate the link through that
port is successfully established.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
 1000BASE-X SFP Port
LED Color Function
1000
LNK/ACT
Green
Lights to indicate the link through that port
is successfully established at 1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
3 Hardware Installation
3.1 Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the
instructions described below.
Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with
the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+
Switch with supplied screws attached to the package. Figure
3-1 shows how to attach brackets to one side of the 802.3at
PoE+ Switch.
2 106 14 18 20
1 95 13 17 19
PoE Max
PWR
4 12
8 16
3 117 15
16-Port 10/100/1000T 802.3at PoE
+
2-Port
10/100/1000T
+
2-Port 1000X SFP Desktop Switch
19 20
1000X SFP
Standard
VLAN
Extend
PoE-in-Use
LNK
ACT
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
GSD-2022P
PoE-in-Use
ACTLNK
2
1
4
3
6
5
8
7
9 10 11
GSD-1121XP
8-Port 10/100/1000T 802.3at PoE
+
2-Port 2.5G
802.3at PoE
+
1-Port 10G SFP
+
Ethernet Switch
PWR
11
ACT
LNK10G
2.5G
10G
SFP
+
17
1000X SFP
LNK
PoE-in-Use
ACT
FGSD-1821P
Standard
VLAN
Extend
PWR
PoE Max
2 6
4 8
10 14
12 16
1 5
3 7
9 13
11 15
18
17
16-Port 10/100TX 802.3at PoE
+
2-Port 10/100/1000T
+
1-Port Shared 1000X SFP Desktop Switch
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
Figure 3-1: Attaching the Brackets to the 802.3at PoE+ Switch.
Caution
You must use the screws supplied with the mounting
brackets. Damage caused to the parts by using incorrect
screws would invalidate the warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the
opposite side.
Standard Mode (default)
Power
PoE IP Camera
PoE
100 meters (328 feet)
PoE
100BASE-TX UTP with PoE
FGSD-1821P
Standard
VLAN
Extend
VLAN Isolation Mode
NVR
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
PoE
100BASE-TX UTP with PoE
FGSD-1821P
IP Camera
IP Camera
IP Camera
Ports 17~18 and SFP Port 17
to Ports 1~16 Access Permitted
1000BASE-T UTP
Standard
VLAN
Extend
Extend Mode
Ports 1 to 8
Power
250 meters (820 feet)
PoE
PoE
10BASE-T UTP with PoE
PoE IP Camera
FGSD-1821P
Standard
VLAN
Extend
2. Hardware Introduction
2.1 Front Panel
The front panel of the 802.3at PoE+ Switch consists of 16/24 auto-
sensing 10/100BASE-TX RJ45 ports, 2 auto-sensing 10/100/1000BASE-T
RJ45 ports and 1 1000BASE-X SFP port. The LED Indicators are also
located on the front panel of the 802.3at PoE+ Switch.
17
1000X SFP
LNK
PoE-in-Use
ACT
FGSD-1821P
Standard
VLAN
Extend
PWR
PoE Max
2 6
4 8
10 14
12 16
1 5
3 7
9 13
11 15
18
17
16-Port 10/100TX 802.3at PoE
+
2-Port 10/100/1000T
+
1-Port Shared 1000X SFP Desktop Switch
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
Figure 2-1: FGSD-1821P Switch Front Panel
1000X SFP
25
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
26
FGSD-2621P
Standard
VLAN
Extend
LNK
ACT
4 12
8 16
20
24
3 11
7 15
19
23
2 10
6 14
18
PoE Max
22
1 9
5 13
17 PWR
21
26
25
PoE-
in-Use
26
Figure 2-2: FGSD-2621P Switch Front Panel
2.2 LED Indicators
 System
LED Color Function
PWR Green Lights to indicate the Switch has power.
PoE
(max.)
Green
O to indicate the PoE power is less than 80%
of total power.
Lights to indicate the PoE power is above
80%.
2.3 Multiple Functions of DIP Switch
The front panel of the 802.3at PoE+ Switch provides one DIP switch for
Standard, VLAN or Extend mode selection. The detailed descriptions
are shown in the following table.
DIP Switch Mode Function
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a general switch and all PoE+
ports operate at 10/100Mbps auto-negotiation.
All ports can communicate with one another.
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a VLAN isolation switch and
For FGSD-1821P:
1. Ports 1 to 16 will isolate respectively.
2. Ports 1 to 16 can only communicate with
ports 17~18 (uplink ports) and SFP port 17.
For FGSD-2621P:
1. Ports 1 to 24 will isolate respectively.
2. Ports 1 to 24 can only communicate with
ports 25~26 (uplink ports) and SFP port 26
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a Long Reach PoE switch and
1. Ports 1 to 8 support farthest transmission
distance of up to 250 meters
2. Ports 1 to 8 have a data rate of 10Mbps
3. All ports can communicate with one
another.
Note
Please select a DIP switch mode before powering on the
802.3at PoE+ Switch.
2.4 Rear Panel
The rear panel of the 802.3at PoE+ Switch indicates an AC power
socket, which accepts input power from 100 to 240V AC, 50-60Hz, 5A.
50/60Hz
100-240V , 5A max.
Figure 2-3: Switch Rear Panel
 AC Power Receptacle
Power
Notice
The device is a power-required device, which means
it will not work till it is powered. If your networks
should be active all the time, please consider using UPS
(uninterrupted power supply) for your device. It will
prevent you from network data loss or network downtime.
Power
Notice
In some areas, installing a surge suppression device may
also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch,
use suitable screws to securely attach the brackets to the
rack, as shown in Figure 3-2.
2 106 14 18 20
1 95 13 17 19
PoE Max
PWR
4 12
8 16
3 117 15
16-Port 10/100/1000T 802.3at PoE
+
2-Port
10/100/1000T
+
2-Port 1000X SFP Desktop Switch
19 20
1000X SFP
Standard
VLAN
Extend
PoE-in-Use
LNK
ACT
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
GSD-2022P
17
1000X SFP
LNK
PoE-in-Use
ACT
FGSD-1821P
Standard
VLAN
Extend
PWR
PoE Max
2 6
4 8
10 14
12 16
1 5
3 7
9 13
11 15
18
17
16-Port 10/100TX 802.3at PoE
+
2-Port 10/100/1000T
+
1-Port Shared 1000X SFP Desktop Switch
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
Figure 3-2: Mounting the 802.3at PoE+ Switch in a Rack
Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at
complied PDs and other network devices.
A. Connect one end of a standard network cable to the
10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at
PoE+ Switch.
B. Connect the other end of the cable to the network devices such as
printer servers, workstations or routers, etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall
outlet.
When the 802.3at PoE+ Switch receives power, the power LED should
remain solid Green.