8-/16-/24-Port 10/100TX 802.
Copyright Copyright © 2021 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications.
Table of Contents 1. Introduction................................................................................................ 5 1.1 Package Contents................................................................................. 5 1.2 Product Description............................................................................... 6 1.3 Features.............................................................................................10 1.4 Specifications.............................................
1. Introduction Thank you for purchasing PLANET 8/16/24-Port 10/100TX 802.3at PoE+ SFP Ethernet Switch series, FGSD-1022VHP, FGSW-1822VHP and FGSW-2622VHP. The descriptions of these models are shown below: FGSD-1022VHP 8-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Desktop Switch with LCD PoE Monitor FGSW-1822VHP 16-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP + 2-Port SFP Ethernet Switch with LCD PoE Monitor FGSW-2622VHP 24-Port 10/100TX 802.
If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. 1.2 Product Description Ideal High-performance Integration Solution for Secure IP Surveillance Infrastructure Particularly designed for the growing popular IP surveillance applications, PLANET FGSD/FGSW 802.
The FGSD/FGSW 802.3at PoE+ Switch series is equipped with 8/16/24 10/100BASE-TX ports featuring 30-watt 802.3at Power over Ethernet Plus (PoE+) copper interfaces. With a total PoE power budget of up to 120/300 watts and non-blocking data switching performance, the FGSD/FGSW 802.3at PoE+ Switch series fulfills the demand of sufficient PoE power for HD IP surveillance.
Main Menu Switch Port Information 01 30.3W ---M -33M 08 ----W ---M ---M 01 — Switch Mode 02 ----W ---M ---M 09 -8.3W ---M -11M 02 — Budget Control 03 ----W ---M ---M 10 ----W ---M ---M 04 15.4W -10M ---M 11 -OFF- ---M ---M 03 — PSE Port Priority 04 — PSE Port Enable 05 ----W ---M ---M 12 ----W ---M ---M 05 — PD Type 06 ----W ---M ---M 13 17.
The VLAN operation mode features the port-based VLAN function that can help to prevent the IP camera’s multicast or broadcast storm from influencing each other. VLAN Isolation Mode NVR PoE IP Camera PoE 1000 Standard Ports 17 and 18 for uplink Ports 1~16 Access Permitted > VLAN IP Camera Ports 1 to 16 Access Denied PoE Extend IP Camera FGSW-1822VHP PC 1000 1000BASE-SX/LX Fiber-optic 100BASE-TX UTP PoE 100BASE-TX UTP with PoE In the Extend operation mode, the FGSD/FGSW 802.
Robust Protection The FGSD/FGSW 802.3at PoE+ Switch series provides contact discharge of ±4/6KV DC and air discharge of ±6/8KV DC for Ethernet ESD protection. It also supports ±4/6KV surge immunity to improve product stability and protects users’ networks from devastating ESD attacks, making sure the flow of operation does not fluctuate. Easy Installation and Cable Connection As data and power are transmitted over one cable, the FGSD/FGSW 802.
Auto detects powered device (PD) Circuit protection prevents power interference between ports Remote power feeding up to 100m in standard mode and 250m in extend mode Smart LCD The LCD switch features “Standard”, “VLAN” and “Extend” mode selection; the “Extend” mode features 20-watt PoE transmission distance of 250m at speed of 10Mbps and VLAN isolation The LCD switch is able to isolate ports to prevent broadcast storm and defend DHCP spoofing Power low-voltage, power over-voltage and PS
1.4 Specifications Model FGSD-1022VHP FGSW-1822VHP FGSW-2622VHP Hardware Specifications 802.3af/at PoE Injector Port 8 16 24 10/100BASE-TX MDI/ MDIX Ports 8 16 24 10/100/1000BASE-T MDI/MDIX Ports 2 (Combo) 2 1000BASE-X SFP/ mini-GBIC Slots 2 (Combo) 2 Switch Architecture Switch Fabric Store-and-Forward 5.6Gbps/ non-blocking Switch 4.17Mpps@64 bytes Throughput@64 bytes MAC Address Table Maximum Frame Size Flow Control LED Indicators Buttons Dimensions (W x D x H) Enclosure 12 12.
Weight 1.8kg 3.4kg 3.4kg Power Requirements 100-240V AC, 50/60Hz, 2.5A max. 100-240V AC, 50/60Hz, 5A max. Power Consumption/ Dissipation Max. 130 watts/ 446 BTU Max. 330 watts/1132 BTU 1 3 Contact discharge of ±4KV DC Air discharge of ±6KV DC Contact discharge of ±6KV DC Air discharge of ±8KV DC ±4KV ±6KV Thermal Fan ESD Protection Surge Protection Power over Ethernet IEEE 802.3af Power over Ethernet/PSE IEEE 802.
Environment Operating Storage 14 Temperature: 0 ~ 50 degrees C Relative Humidity: 5 ~ 90% (non-condensing) Temperature: -10 ~ 60 degrees C Relative Humidity: 10 ~ 90% (non-condensing) * Temperature: < 40 degrees C; Humidity: < 90% Temperature: > 40 degrees C; Humidity: < 50% Temperature: Temperature: -10 ~ 70 degrees C -10 ~ 70 degrees C Relative Humidity: 5 ~ 90% Relative Humidity: (non-condensing) 5 ~ 90% (non-condensing)
2. Hardware Description These switches provide three different running speeds – 10Mbps, 100Mbps and 1000Mbps and automatically distinguish the speed of the incoming connection. This section describes the hardware features of 802.3at PoE+ Switch. For easier management and control of the 802.3at PoE+ Switch, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the 802.
Smart LCD The Smart LCD that is located on the front panel of the FGSD-1022VHP, FGSW1822VHP, FGSW-2622VHP 802.3at PoE+ Switch provides “PoE Management and Status”, “Switch Mode: Standard, VLAN, Extend”, “Budget and Bandwidth Control”, “Screen Saver”, “Fan Control”, and “Factory Default”. 2.1.1 LCD Monitor Indicators The 802.
The detailed Smart LCD description of each item is shown below: Parameters Description 30.3W (example) It means the output power port of the PoE switch. OLP It means the port is overloaded corresponding to the PSE, and the port stops powering. ULP It means the port corresponding to the PSE is lightly loaded and the port stops powering (When the current on the network is less than 7.5mA, the PSE thinks the PD has been dialed out and the port stops powering).
10/100Mbps PoE Ports LED LNK/ACT Color Function Lights Indicates the link through that port is successfully established at 10/100Mbps. Blinks Indicates that the Switch is actively sending or receiving data over that port. Green Lights Indicates the port is providing DC in-line power. PoE-in-Use Amber Off Indicates the connected device is not a PoE powered device (PD).
2.2 Rear Panel The rear panel of the 802.3at PoE+ Switch has an AC power socket (100-240V AC, 50/60Hz, 2.5/5A max.). 100-240V , 2.5A max. 50/60Hz Figure 2-4: FGSD-1022VHP Switch Rear Panel 100-240V , 50/60Hz, 5A max. Figure 2-5: FGSW-1822VHP/FGSW-2622VHP Switch Rear Panel AC Power Receptacle For compatibility with electrical outlet standard in most areas of the world, the 802.3at PoE+ Switch’s power supply automatically adjusts to line power in the range of 100-240V AC, 50/60Hz, 2.5/5A max.
2.3 LCD Management The operation of the 5 buttons (Menu, Enter, Back, Up and Down) on the panel: Switch Port Information Menu (5 sec) Up 01 30.3W ---M -33M 08 ----W ---M ---M 02 ----W ---M ---M 09 -8.3W ---M -11M 03 ----W ---M ---M 10 ----W ---M ---M Enter 04 15.4W -10M ---M 11 -OFF- ---M ---M 05 ----W ---M ---M 12 ----W ---M ---M 06 ----W ---M ---M 13 17.
2.3.1 Switch Mode There are three modes -- “Standard”, “VLAN” and “Extend” – for selection. Model FGSD-1022VHP Switch Mode FGSW-1822VHP FGSW-2622VHP Function Standard This mode makes the 802.3at PoE+ Switch operate as a general (default) switch and all PoE ports operate at 10/100Mbps auto-negotiation. VLAN This mode makes the FGSD-1022VHP operate as a VLAN isolation switch and 1. Port 1 to port 8 will isolate respectively. 2. Port 1 to port 8 can only communicate with port 9~12 (uplink port).
Standard Mode (default) > Standard PoE IP Camera VLAN Extend PoE Power FGSW-1822VHP 100 meters (328 feet) 100BASE-TX UTP with PoE PoE VLAN Isolation Mode NVR PoE IP Camera PoE 1000 Standard Ports 17 and 18 for uplink Ports 1~16 Access Permitted Ports 1 to 16 Access Denied IP Camera > VLAN PoE Extend IP Camera FGSW-1822VHP PC 1000BASE-SX/LX Fiber-optic 1000 100BASE-TX UTP 100BASE-TX UTP with PoE PoE Extend Mode Standard PoE IP Camera VLAN > Extend PoE Power FGSW-1822VHP 250 meters
2.3.2 Budget Control Due to the power allocation strategy of PSE, when the residual power of PoE is too large, the power distribution of the port can be increased as much as possible by increasing the power trimming of the PSE, so that the utilization of the PSE power supply can be improved. There are four levels of budget control named Unchanged (default), Add 5% PB, Add 10% PB and Add 15% PB. Note 1. The default PoE budget is 120W/300W in unchanged mode.
2.3.4 PSE Port Enable Allows user to disable or enable per port PoE function. The default is “Enable”. 2.3.5 PD Type Changing the PoE power-up mode can let non-standard PDs pass the procedures of PoE power delivery process. This way, the switch can supply power to nonstandard PDs. The FGSD/FGSW 802.3at PoE+ Switch series can set the PoE powerup mode to be in Enhance mode, Standard mode or Legacy mode by the user interface.
2.3.6 Alive Check The FGSD/FGSW 802.3at PoE+ Switch series can be configured to monitor connected PD’s status in real time via traffic detection. Once there is no traffic at interval time, the FGSD/FGSW 802.3at PoE+ Switch series is going to restart PoE port power, and bring the PD back to work. It will greatly enhance the reliability and reduce administrator management burden. Object Description Port Select the port number to enable Alive Check.
2.3.7 Bandwidth Detection When the network transmits “the highest data rate”, more than the set value, over a single port, the switch will set off an alarm to warn the overuse of the bandwidth. There are four levels of budget control, namely Unlimited (default), 70Mbps, 80Mbps and 90Mbps. 2.3.8 Fan Control Fan control is to achieve the set power with intelligent operation. There are four levels of budget control, namely Always ON, 20% PB (default), 40% PB and 60% PB. 2.3.
2.3.10 Language There are two languages, namely English and Chinese. 2.3.11 Default Setting Restore the device to default. 2.3.12 System Show the system information.
3. Hardware Installation Start up Please refer to the following for your cabling: 10/100BASE-TX All 10/100BASE-TX ports come with Auto-Negotiation capability. They automatically support 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100BASE-TX ports, and then turn on the 802.3at PoE+ Switch. The port will automatically run at 10Mbps, 20Mbps, 100Mbps or 200Mbps after the negotiation with the connected device.
3.1 Desktop Installation To install the 802.3at PoE+ Switch on desktop, simply follow the following steps: Step 1: Attach the rubber feet to the recessed areas on the bottom of the 802.3at PoE+ Ethernet Switch, as shown in Figure 3-1.
3.2 Rack Mounting To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below. Step 1: Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+ Switch with supplied screws attached to the package. Figure 3-2 shows how to attach brackets to one side of the 802.
3.3 Installing the SFP Transceiver The sections describe how to insert an SFP transceiver into an SFP slot of the 802.3at PoE+ Switch. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the 802.3at PoE+ Switch, as the Figure 3-4 shows. 1 MGB-Series Module 2 LC Fiber Cable Figure 3-4: Plugging in the SFP Transceiver Approved PLANET SFP Transceivers PLANET 802.
Note It is recommended to use PLANET SFP on the 802.3at PoE+ Switch. If you insert an SFP transceiver that is not supported, the 802.3at PoE+ Switch will not recognize it.. 1. Before we connect the 802.3at PoE+ Switch to the other network device, we have to make sure both sides of the SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX; 1000BASE-LX to 1000BASELX. 2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
Never pull out the module without lifting up the lever of the module and turning it to a horizontal position. Directly pulling out the module could damage the module and the SFP module slot of the 802.3at PoE+ Switch. Note 3.4 Product Applications Department/Workgroup PoE Switch: Providing 8/16/24 PoE in-line power interfaces, the 802.3at PoE+ Switch can easily build a power that centrally controls IP phone system, IP camera system and wireless AP group for enterprises.
3.5 Power over Ethernet Powered Devices 3~5 watts 6~12 watts Wireless LAN Access Points Access points can readily be installed in museums, sightseeing sites, airports, hotels, campuses, factories and warehouses. 10~12 watts IP Surveillance For the sake of security, install IP cameras around enterprises, museums, campuses, hospitals and bank without considering location and electrical outlets.
4. Power over Ethernet Overview What is PoE? PoE is an abbreviation of Power over Ethernet. The PoE technology means a system safely transmits both power and data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with Cat3 cable for low power levels.
intermediary device between a non-PoE capable switch and a PoE device, it is called a mid-span. An external PoE injector is a mid-span device. Powered Device A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP phones, and IP cameras. Many powered devices have an auxiliary power connector for an optional, external power supply.
The data pairs are used. Since Ethernet pairs are transformers coupled at each end, it is possible to apply DC power to the center tap of the isolated transformer without upsetting the data transfer. In this mode of operation, the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
5. Troubleshooting This chapter contains information to help you solve issues. If the 802.3at PoE+ Switch is not functioning properly, make sure the 802.3at PoE+ Switch was set up according to instructions in this manual. The Link LED is not lit. Solution: Check the cable connection and also try to swap one new cable. LNK/ACT link LED is lit, but the traffic is irregular. Solution: Make sure the attached device is not set to full duplex. Some devices use a physical or software switch to change duplex modes.
EC Declaration of Conformity For the following equipment: *Type of Product : 8-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP combo Desktop Switch with LCD PoE Monitor (120 Watts) *Model Number FGSD-1022VHP : * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.
EC Declaration of Conformity For the following equipment: *Type of Product : 16/24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Ethernet Switch with LCD PoE Monitor (300W) *Model Number FGSW-1822VHP, FGSW-2622VHP : * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.
