Datasheet

FGSD-1008HPS
2
• High performance Store and Forward architecture, runt/
CRClteringeliminateserroneouspacketstooptimizethe
network bandwidth
• Supports VLAN
– Port-based VLAN, up to 10 VLAN groups
– IEEE 802.1Q tagged VLAN
– Protocol VLAN
– Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
– GVRP
– Voice VLAN
• Supports SpanningTreeProtocol
– STP (IEEE 802.1D Spanning Tree Protocol)
– RSTP (IEEE 802.1w Rapid Spanning Tree Protocol)
– MSTP (IEEE 802.1s Multiple Spanning Tree Protocol)
– STPBPDUltering, BPDUGuard
• Supports LinkAggregation
– IEEE 802.3ad Link Aggregation Control Protocol (LACP)
– 1 LACP group, up to 2 ports per LACP group
– Cisco ether-channel (static trunk)
– 1 trunk group, up to 2 ports per trunk group
• Provides port mirror (many-to-1)
• Loop detection
Quality of Service
• Ingress/Egress Rate Limit per port bandwidth control
• Storm Control support
– Broadcast/ Multicast /DLF (Destination Lookup Fail)/ARP/
ICMP
• Trafcclassication
– IEEE 802.1p Qos/CoS
– TCP/UDP/DSCP/IP precedence of IPv4/IPv6 packets
• Strict priority and Weighted Round Robin (WRR) CoS
policies
Multicast
• Supports IPv4 IGMP snooping v1/ v2 and v3
• Supports IPv6 MLD snooping v1, v2
Security
• Access Control List
– IPv4/IPv6 IP-based ACL
– MAC-based ACL
• Port-MAC-IP Address Binding
– Port-MAC-IP Port Setting
– Port-MAC-IP Entry Setting
• MAC Address Binding
– Static MAC
– MAC Filtering
• DHCPsnoopingtolterdistrustedDHCPmessages
Solution for IPv6 Networking
With the support for IPv6/IPv4 protocol, and easy and friendly management
interfaces, the FGSD-1008HPS is the ideal choice for IP surveillance, VoIP and
wireless service providers to connect with the IPv6 network. It also helps SMBs to
step in the IPv6 era with the lowest investment and without having to replace the
network facilities even though ISPs establish the IPv6 FTTx edge network.
Built-in Unique PoE Functions for Surveillance Management
As a managed PoE Switch for surveillance network, the FGSD-1008HPS features
the following intelligent PoE management functions:
■PDAliveCheck
■PoEPortSequence
■PoESchedule
Intelligent Powered Device Alive Check
The FGSD-1008HPS can be configured to monitor a connected PD status in real
time via ping action. Once the PD stops working and it is without response, the
FGSD-1008HPS will resume the PoE port power and bring the PD back to work. It
will greatly enhance the network reliability through the PoE port resetting the PD’s
power source, thus reducing administrator management burden.
IPv4 Network
IPv6 Network
Application
IPv6
Stack
IPv4
Stack
Transport Layer
TELNET WEB
SSHSNMP
ICMPACL
DHCPNTP
IPv6 Management HostIPv4 Management Host
FGSD-1008HPS
PT PoE Camera
Ping Request
Ping Request
Check alive status for 3 times
Restart PoE device if without response
Ping Echo
No Response......
PD Alive!!
Step 1
Step 3
Step 2
Step 4
ON
PoE
ON
ON
PoE
OFF
PD Status
Good!!
Alarm Notification
PoE Port Sequence
To prevent all the PoE ports of the FGSD-1008HPS from being active at the same
time when the Switch has booted up, the PoE ports of the FGSD-1008HPS can
beconguredtoalloweachporttobeactivatedatanintervaltime.Inaddition,the
“Delay”setting is to delay power feeding on each port when the FGSD-1008HPS
has completely booted up.