Industrial Renewable Energy 4-Port 10/100/1000T 802.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Trademarks Copyright © PLANET Technology Corp. 2017. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 TABLE OF CONTENTS 1. INTRODUCTION ......................................................................................................... 6 1.1 Package Contents............................................................................................... 6 1.2 Product Description ............................................................................................. 6 1.3 How to Use This Manual ..........
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.4 Security ................................................................................................ 58 4.4.5 Route.................................................................................................... 63 4.4.6 QoS (Quality of Service)....................................................................... 65 4.5 Battery Management ............................................................
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 1. INTRODUCTION 1.1 Package Contents Open the box of the Renewable Energy Switch and carefully unpack it. The box should contain the following items: The BSP-360 x 1 Quick Installation Guide x 1 Wall Mounting Kit x 1 DIN Rail Kit x 4 RJ45 Dust Cap x 2 If any of the above items are missing, please contact your seller immediately. 1.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Zero-Carbon and Stable Power Supply The BSP-360 utilizes the solar power sourcing and co-works with the common nickel-cadmium battery or lead-acid battery to form an independent solar power supply system for outdoor network system. The BSP-360 delivers zero-carbon and uninterruptible PoE power supply for continuous outdoor wireless and IP surveillance applications without the need of any cabling.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Low Voltage Cut-Off Protection If the power is too low to empower the system and IP devices, the system will automatically power off the device with low priority to make sure the system works normally, and an alert is then sent to the administrator at the same time.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Scheduled Power Recycling The BSP-360 allows each of the connected PoE IP cameras or PoE wireless access points to reboot at a specific time each week. Therefore, it will reduce the chance of IP camera or AP crash resulting from buffer overflow.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 PoE Usage Monitoring and Intelligent LED Indicator for Real-time PoE Usage Via the power usage chart in the web management interface, the BSP-360 enables the administrator to monitor the status of the power usage of the connected PDs in real time. Thus, it greatly enhances the management efficiency of the facilities.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 1.3 How to Use This Manual This User Manual is structured as follows: Section 2, Installation It explains the functions of Renewable Energy Switch and how to physically install the Renewable Energy Switch. Section 3, Management It contains information about the software function of the Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 1.4 Product Features Physical Port 5-port 10/100/1000BASE-T Gigabit RJ45 copper with 4-port IEEE 802.3at/af PoE Injector (Port 1 to Port 4) RJ45 type interface for basic management and setup USB type A female for setting file backup and restore Power over Ethernet Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE Backward compatible with IEEE 802.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Supports -10 to 60 degrees C operating temperature Supports ESD 6KV DC Ethernet protection Redundant power design – 24V~45V DC wide power input Switching Hardware based 10/100Mbps (half/full duplex), 1000Mbps (full duplex), auto-negotiation and auto MDI/MDI-X Features Store-and-Forward mode with wire-speed filtering and forwarding rates IEEE 802.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 1.5 Product Specifications Product BSP-360 Hardware Specifications LAN: 5 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port-1 to Port-5, Copper Ports bridge mode) WAN: 1 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port-5, gateway mode) PoE Injector Port 4 ports with 802.3af/802.3at PoE injector function (Port-1 to Port-4) USB 1 USB Type A female for setting backup 4 PoE out 52VDC; max.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Level 0: -24V~2.1V (±0.1V) Level 1: 2.1V~24V (±0.1V) Open collector to 24V DC, 100mA max. Power Requirements PV in: 24~45V DC Battery in: 24V DC 5.04 watts, 17.1BTU (Standby without PoE function) Power Consumption/ Dissipation 6.96 watts, 23.7 BTU (Full loading without PoE function) 135.36 watts, 461.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Battery Charging Characteristics Bulk charge (constant current), Absorption charge (constant voltage) Charge Algorithm and Floating charge. Absorption and Floating charge with PWM protection.
Industrial Renewable Energy 4-Port 10/100/1000T 802.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 2. INSTALLATION This section describes the hardware features of Renewable Energy Switch. For easier management and control of the Renewable Energy Switch, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Renewable Energy Switch, read this chapter carefully. 2.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Item Interface 1 Port-1~Port-4 Description 4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports with 802.af/at PoE+ injector function. One 10/100/1000BASE-T RJ45 auto-MDI/MDI-X port. 2 Port-5 Port-5 functions as WAN port when the operation mode of BSP-360 is configured to “Gateway mode” Connect the USB storage to USB port and back up the configuration file. 3 USB 4 Reset Button 5 2.1.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 LED Color Function Off To indicate the connected device is not a PoE Powered Device (PD). 10/100/1000BASE-T Interfaces (Port-5) LED Color Function LNK/ACT Green Blinks 2.1.3 To indicate the link through that port is successfully established. Switch Upper Panel The Upper Panel of the Renewable Energy Switch comes with a DC inlet power socket and one terminal block connector with 6 contacts.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 The wire gauge for the terminal block should be in the range from 14 to 24 AWG. DO Connectors Level 0: -24V~2.1V (±0.1V) Level 1: 2.1V~24V (±0.1V) 2.1.4 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle (3 & 4) of the terminal block connector as the picture shows below.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 2.1.5 Wiring the Digital Output The 6-contact terminal block connector on the rear panel of BSP-360 and the 3/4 pin is used for Digital Output. Please follow the steps below to insert wire. The BSP-360 offers one DO groups. 3 is DO and 4 is GND. Please tighten the wire-clamp screws for preventing the wires from loosening.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 In this paragraph, we will describe how to install the Renewable Energy Switch and the installation points attended to it. 2.2.1 Installation Steps The following section describes the hardware installation of the BSP-360. Before connecting any network device to the BSP-360, read this chapter carefully. Please follow the following steps to install the system: Step 1.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Step 2. Install battery (1) Connect the negative electrode of the battery to the terminal for the negative electrode of the battery on the BSP-360. (2) Connect the positive electrode of the battery to the terminal for the positive electrode of the battery on the BSP-360.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Step 3. Install PV Panel (1) Connect the negative electrode of the PV panel to the terminal for the negative electrode of the PV panel on the BSP-360. (2) Connect the positive electrode of the PV panel to the terminal for the positive electrode of the PV panel on the BSP-360.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Step 4. Connect 802.3af/802.3at PoE Device Connect the PoE devices to ports 1~ 4 on the BSP-360. Check the PoE-in-Use LED. If the network devices such as PoE camera and PoE wireless AP are powered, the PoE-in-use LED will turn ON and Link/Act LED will blink for a successful connection or data receiving. Please use Cat5/5e or above cable and the maximum distance should within 100 meters.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 One Powered Device Two Powered Devices Install the terminal block on the BSP-360. The voltage of DC out is based on the battery voltage and the maximum DC out from the BSP-360 is 24VDC, 1A. The wire gauge for the terminal block should be in the range from 14 to 24 AWG. The external device should also be grounded properly. Please ensure the output voltage is correct for remote device.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Step 6. Connect to PC After completing the above 6 steps, the BSP-360 are ready for service. 2.2.2 DIN-rail Mounting This section describes how to install the Renewable Energy Switch. There are two methods to install the Renewable Energy Switch -- DIN-rail mounting and wall-mount plate mounting. Please read the following topics and perform the procedures in the order being presented.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Step 2: Lightly slide the DIN-rail into the track. Step 3: Check whether the DIN-rail is tightly on the track. Please refer to the following procedures to remove the Renewable Energy Switch from the track. Step 4: Lightly remove the DIN-rail from the track.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 2.2.3 Wall Mount Plate Mounting To install the Renewable Energy Switch on the wall, please follow the instructions below. Follow all the DIN-rail installation steps as shown in the example. Step 1: Remove the DIN-rail from the Renewable Energy Switch. Use the screwdriver to loosen the screws to remove the DIN-rail. Step 2: Place the wall-mount plate on the rear panel of the Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Step 3: Use the screwdriver to screw the wall mount plate on the Renewable Energy Switch. Step 4: Use the hook holes at the corners of the wall mount plate to hang the Renewable Energy Switch on the wall. Step 5: To remove the wall mount plate, reverse the steps above.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 3. MANAGEMENT This chapter describes how to manage the Renewable Energy Switch with the following topics included: – Overview – Requirements – Management Method 3.1 Overview The Renewable Energy Switch provides a user-friendly, Web interface where you can perform various device configuration and management activities, including: System SNMP Power over Ethernet Battery Management 3.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 3.3.1 Web Management The Renewable Energy Switch can be configured through an Ethernet connection. The factory default IP address is 192.168.0.100 with subnet mask 255.255.255.0, so please make sure the manager PC must be set to the same IP subnet address. For example, if Renewable Energy Switch IP address is set to factory default, then your manager PC should be set to 192.168.0.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Figure 3-3-2: Renewable Energy Switch Web Login Screen 1. For security reason, please change and memorize the new password after this first setup. 2. Only accept command in lowercase letter under Web interface. 3.3.2 PLANET Smart Discovery Utility For easily listing the Renewable Energy Switch in your Ethernet environment, Planet Smart Discovery Utility from PLANET download center is an ideal solution.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Figure 3-3-3: Planet Smart Discovery Utility Screen If there are two LAN cards or above in the same administrator PC, choose a different LAN card by using the “Select Adapter” tool.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 After setup is completed, press the “Update Device”, “Update Multi” or “Update All” button to take effect. The definitions of the 3 buttons above are shown below: Update Device: Use current setting on one single device. Update Multi: Use current setting on multi-devices. Update All: Use current setting on whole devices in the list. The same functions mentioned above also can be found in “Option” tools bar.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4. WEB CONFIGURATION The Renewable Energy Switch provides Web interface for PoE smart function configuration and makes the Renewable Energy Switch operate more effectively. They can be configured through the Web browser. A network administrator can manage and monitor the Renewable Energy Switch from the local LAN. This section indicates how to configure the Renewable Energy Switch to enable its smart function. 4.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Switch. Explained in section 4.6 Maintenance Provides firmware upgrade and setting file restore/backup configuration of Renewable Energy Switch. Explained in section 4.7.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.2 Web Panel At the top of the Web management page, the active panel displays the power status and the link status of management port and PoE ports. Figure 4-2-1: Web Panel Screen Object DC IN Icon Function To indicate the voltage of DC in. To indicate the battery capacity is 70~100%. To indicate the battery capacity is 70~100% and charging by solar PV. To indicate the battery capacity is 40~69%. Bat Cap.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.3 System The System function provides system information which also allows user to manage the Renewable Energy Switch system as Figure 4-3-1 is shown below: Figure 4-3-1: System Function Menu The page includes the following information: Object Description System Information Operation Mode Time Zone User Management SNMP 4.3.1 Display the System Status, Statistics, System Log. Explained in section 4.3.1.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.3.1.1 Status This section displays system information of Renewable Energy Switch as the screen in Figure 4-3-3 appears. Table 4-3-1 describes the system information of the Renewable Energy Switch. Figure 4-3-3: System Information Web Page Screen Object Description System Information Firmware Version Displays the current firmware version of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Power Information Nickel-cadmium or Lead-acid battery. Battery Type Go to the Battery management to select the battery type. Displays the install time of battery. Install Time of Battery Go to the Battery management to enter the install time. Displays the life of battery. Battery Life Go to the Battery management to enter the life. Displays the time of battery recharge.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Time Interval Select 30 min. or 60 min. Export to excel Download this data chart excel to PC. Auto Export Setting Download this data chart to FTP server. Table 4-3-2: Descriptions of the Statistics Objects The statistics will recount after reboot. 4.3.1.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description occurs every 3 seconds. Refresh Press this button to refresh current Web page. Clear Press this button to clear system log information. Table 4-3-3: Descriptions of the System Log Objects 4.3.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.3.3 Time Zone This section assists you in setting the Renewable Energy Switch’s system time. You can either select to set the time and date manually or automatically obtain the GMT time from Internet as the screen in Figure 4-3-7 appears and Table 4-3-5 describes the NTP Configuration object of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.3.4 User Management This section provides the Password Setting of Renewable Energy Switch as the screen in Figure 4-3-8 appears. Table 4-3-6 describes the Password Setting objects of Renewable Energy Switch. Figure 4-3-8: Password Setting Web Page Screen Object Description User Name Allows to input current User Name of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.3.5 SNMP This section provides SNMP setting of Renewable Energy Switch as the screen in Figure 4-3-9 appears and Table 4-3-7 describes the SNMP object of Renewable Energy Switch. Figure 4-3-9: SNMP Web Page Screen Object SNMP Agent SNMP Read Community SNMP Write Community Description Disable or enable the SNMP Agent function of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description SNMP Trap Destination Allows to send SNMP trap to an assigned workstation.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4 TCP/IP The TCP/IP function provides WAN, LAN and network configuration of Renewable Energy Switch as Figure 4-4-1 is shown below: Figure 4-4-1: TCP/IP Function Menu The page includes the following information: Object Description WAN Allow to set WAN interface. Explained in section 4.4.1. LAN Allow to set LAN interface. Explained in section 4.4.2. Server Allow to set Port Forwarding and DMZ.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.1.1 WAN Setup This page is used to configure the parameters for Internet network which connects to the WAN port of Renewable Energy Switch as the screen in Figure 4-4-3 appears. Table 4-4-1 describes the WAN Objects Screen of Renewable Energy Switch. Here you may change the access method to static IP, DHCP, PPPoE, PPTP or L2TP by click the item value of WAN Access type.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. IP Address Enter the IP address assigned by your ISP. Subnet Mask Enter the Subnet Mask assigned by your ISP. Default Gateway Enter the Gateway assigned by your ISP. DNS The DNS server information will be supplied by your ISP.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description IP Address Enter the IP address. Subnet Mask Enter the Subnet Mask. Server IP Address Enter the L2TP Server IP address provided by your ISP. User Name Enter your L2TP user name. Password Enter your L2TP password. This option specifies the Host Name of the Renewable Energy Switch. Host Name The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1492 Bytes.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 If you get Address not found error when you access a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses. WAN IP, whether obtained automatically or specified manually, should NOT be on the same IP net segment as the LAN IP; otherwise, the router will not work properly. In case of emergency, press the hardware "Reset" button. 4.4.1.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.2 LAN You can configure LAN connection type manually here and see the LAN Statistics here as Figure 4-4-5 is shown below: Figure 4-4-5: LAN Interface Menu 4.4.2.1 LAN Setup This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point as the screen in Figure 4-4-6 appears. Table 4-4-3 describes the LAN Objects Screen of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Domain Name Default is Planet. 802.1d Spanning Tree You can enable or disable the spanning tree function. Table 4-4-3: Descriptions of the DDNS Objects If you change the device’s LAN IP address, you must enter the new one in your browser to get back to the web-based configuration utility. And LAN PCs’ gateway must be set to this new IP for successful Internet connection. 4.4.2.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.3 Server You can configure Port Forwarding and DMZ here as Figure 4-4-8 is shown below: Figure 4-4-8: Server Setup Menu 4.4.3.1 Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall as the screen in Figure 4-4-9 appears. Table 4-4-5 describes the Port Forwarding Objects Screen of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Select the port number protocol type (TCP, UDP or both). If you are Protocol unsure, then leave it to the default both protocols. Add ports you want to control. For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service Port Range uses a single port number, enter it in both the start and finish fields. The description of this setting.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.4 Security The Security Setup contains submenus of the settings about firewall and access filtering. Please refer to the following sections for the details as Figure 4-4-11 is shown below: Figure 4-4-11: Security Setup Menu 4.4.4.1 Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Port Range Add ports you want to control. Select the port number protocol type (TCP, UDP or both). If you are Protocol unsure, then leave it to the default both protocols. The description of this setting. Comment Table 4-4-7: Descriptions of the Port Filtering Objects 4.4.4.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.4.3 MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Renewable Energy Switch. Use of such filters can be helpful in securing or restricting your local network as the screen in Figure 4-4-14 appears. Table 4-4-9 describes the MAC Filtering Objects Screen of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.4.4 IP Filtering IP Filtering is used to block internet or network access to specific IP addresses on your local network as the screen in Figure 4-4-15 appears. The restricted user may still be able to login to the network but will not be able to access the internet. To begin blocking access to an IP address, enable IP Filtering and enter the IP address of the user you wish to block.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.4.5 Denial of Service (DoS) The Renewable Energy Switch can prevent specific DoS attacks from entering your network as the screen in Figure 4-4-16 appears. A "Denial-of-Service" (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service. Table 4-4-11 describes the IP Filtering Objects Screen of Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Enable DoS Prevention Check to enable DoS function. User may set other related configurations about DoS below. Table 4-4-11: Descriptions of the DOS Objects 4.4.5 Route There are two route types that are Dynamic Route and Static Route. Please refer to the following sections for the details as Figure 4-4-17 is shown below: Figure 4-4-17: Route Setup Menu 4.4.5.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Figure 4-4-19 appears. The destination IP address and subnet mask determine a destination network or host to which the router sends packets through the gateway. Table 4-4-13 describes the Dynamic Route Objects Screen of Renewable Energy Switch. Figure 4-4-19 Static Route Setup Web Page Screen Object Description Enable Static Route Click this box to enable static route.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.4.5.3 Route table Choose menu “Routing Table”, and you can check all of the valid route entries in use as the screen in Figure 4-4-20 appears. The Destination IP address, Gateway, Genmask, Interface and Type will be displayed for each entry. Click the Refresh button to refresh the data displayed. Figure 4-4-20 Route table Web Page Screen 4.4.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Figure 4-4-21 QoS Setup Web Page Screen Object Description Enable QoS Check the box to enable the QoS function. Check the box to adjust the uplink speed automatically by the Renewable Energy Switch. Or enter the uplink data rate manually in the Automatic Uplink Speed field below. Check the box to adjust the downlink speed automatically by the Automatic Downlink Speed Renewable Energy Switch.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.5 Battery Management The page provides for the user to configure the battery parameters so as to achieve the best application condition as the screen in Figure 4-5-1 appears. Table 4-5-1 describes the Battery Management Objects Screen of Renewable Energy Switch. Before the configuration operation, please contact the suppliers of your battery for the product‐specific parameters.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description When the battery voltage is less than the value for low‐voltage disconnection, the controller will not supply to the load so as to protect the battery from over‐discharge. DC 24.8V (23.0~27.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Low Voltage Disconnection / Low Voltage Reconnection When the battery voltage is lower than the value for the low‐voltage disconnection (LVD), the controller will stop supplying power to the load. It requires the charging from the PV panel so as to increase the battery voltage to be above the value for low‐voltage reconnection (LVR) and thus the PoE device can be recovered as the screen in Figure 4-5-2 appears.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Low Voltage Cut-Off Protection If the power is too low to empower the system and IP devices, the system will automatically power off the device with low priority to make sure the system works normally, and an alert is then sent to the administrator at the same time as the screen in Figure 4-5-3 appears.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.6 PoE Management The PSU input power consumption is monitored by measuring voltage and current. The input power consumption is equal to the system’s aggregated power consumption. The power management concept allows all ports to be active and activates additional ports, as long as the aggregated power of the system is lower than the power level at which additional PDs cannot be connected.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.6.1 PoE Configuration This section provides PoE (Power over Ethernet) Configuration and PoE output status of Renewable Energy Switch as screen in Figure 4-6-2 appears. Table 4-6-1 describes the PoE Configuration object of Renewable Energy Switch. Figure 4-6-2: PoE Configuration Web Page Screen Object Description System PoE Admin Mode Allows user to disable / enable PoE function.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Profile1 Profile2 Profile3 Profile4 This function is available when choosing schedule on each port. Allows user to select AT/AF compatibility mode. The default value is AT Power Mode mode. Indicates the power inline mode. The Priority represents PoE ports priority. There are three levels of power priority named Low, High and Critical.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.6.2 PoE Status This page allows user to see the usage of individual PoE Port as the screen in Figure 4-6-3 appears. Table 4-6-2 describes the PoE Status Objects Screen of Renewable Energy Switch. Figure 4-6-3: PoE Status Web Page Screen Object Description Port Number Displays per port status. Watt Displays per port PoE usage. Indicates the AF PoE operation mode of that port.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.6.3 PoE Schedule This section provides user to configure PoE schedule and scheduled power recycling. The “PoE schedule” helps you to enable or disable PoE power feeding for PoE ports during specified time intervals and it is a powerful function to help SMBs or enterprises save power and money.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 The PoE Schedule Profile Web Screens are shown in Figure 4-6-4 and Table 4-6-3. Figure 4-6-4: PoE Configuration Web Page Screen Object Description Allows user to disable or enable per port PoE function, also allow choose PoE Function schedule for enable PoE Schedule function of each port. Indicates the scheduled profile mode.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 PoE Schedule user can configure a duration time for PoE port as default value does not provide power; screen in Figure 4-6-5 and Table 4-6-4 show. Figure 4-6-5: PoE Schedule Web Page Screen Object Description Set the schedule profile mode. Possible profiles are: Profile1 Profile Profile2 Profile3 Profile4 Delete Check to delete the entry.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description Start Min Allows user to set what minute PoE function does by enabling it. End Hour Allows user to set what hour PoE function does by disabling it. End Min Allows user to set what minute PoE function does by disabling it. Allows user to enable or disable the whole PoE port reboot by PoE reboot schedule.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.6.4 PoE Alive Check Configuration The Renewable Energy Switch can be configured to monitor connected PD’s status in real-time via ping action. Once the PD stops working and without response, the Renewable Energy Switch are going to restart PoE port power, and bring the PD back to work. It will greatly enhance the reliability and reduces administrator management burden.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Description request to PD for detecting whether PD is alive or dead. Interval time range is from 10 seconds to 300 seconds. Retry Count (1~5) This column allows user to set how many times system wants to retry ping to PD. For example, if we set count 2, the meaning is that if system retry ping to the PD and the PD doesn’t response continuously, the PoE port will be reset.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.7 Maintenance The page displays the following tabbed panes relative to system configurations as Figure 4-7-1 is shown below:. Figure 4-7-1: Maintenance Function Menu The page includes the following information: Object Ping USB Backup Description Allow you to issue ICMP PING packets to troubleshoot IP. Explained in section 4.7.1. Backup and restore setting file via USB HDD. Explained in section 4.7.2.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.7.1 Ping This page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues. After you press “Ping”, 5 ICMP packets are transmitted, and the sequence number and roundtrip time are displayed upon reception of a reply. The page refreshes automatically until responses to all packets are received, or until a timeout occurs. The ICMP Ping screen in Figure 4-7-2 appears.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 4.7.2 USB Backup This page shows the status of the USB HDD. You may save the setting file to USB HDD and load the setting file from USB HDD as the screen in Figure 4-7-3 appears. Table 4-7-2 describes the WAN Objects Screen of Renewable Energy Switch. Figure 4-7-3: USB Backup Web Page Screen Object Description USB HDD The status of USB HDD.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Object Load Description Settings from Press button to select the setting file, then press File button to upload setting file from PC. Reset Setting to Default Press button to reset to factory default. Table 4-7-3: Descriptions of the System Backup/Restore Objects 4.7.4 Firmware Upgrade This section provides the firmware upgrade of Renewable Energy Switch as the screen in Figure 4-7-5 appears.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 5. POWER OVER ETHERNET OVERVIEW What is PoE? Based on the global standard IEEE 802.3af, PoE is a technology for wired Ethernet, the most widely installed local area network technology adopted today. PoE allows the electrical power necessary for the operation of each end-device to be carried by data cables rather than by separate power cords.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Figure 5-1-1 - Power Supplied over the Spare Pins The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to the center tap of the isolation transformer without upsetting the data transfer. In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 6. THE POE PROVISION PROCESS While adding PoE support to networked devices is relatively painless, it should be realized that power cannot simply be transferred over existing Cat5e cables. Without proper preparation, doing so may result in damage to devices that are not designed to support provision of power over their network interfaces. The PSE is the manager of the PoE process.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 6.2 Classification Once a PD is detected, the PSE may optionally perform classification, to determine the maximal power a PD is to consume. The PSE induces 15.5-25.5V DC, limited to 600 mA, for a period of 10 to 75 ms responded by a certain current consumption by the PD, indicating its power class. The PD is assigned to one of 5 classes: 0 (default class) indicates that full 15.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 6.5 Power Disconnection Scenarios The IEEE 802.3af / IEEE 802.3at standard requires that devices powered over Ethernet be disconnected safely (i.e. power needs to be shut down within a short period of time following disconnection of a PD from an active port). When a PD is disconnected, there is a danger that it will be replaced by a non-PoE-ready device while power is still on.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 APPENDIX A. A.1 MDI Settings The Medium-Dependent Interface (MDI or RJ45) serves as the data/power interface between Ethernet elements. As such, it has two optional connection methods to carry the power. Named Alternative A & B, Table 1 details the two power feeding alternatives.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 A.3 DATA OUT PoE Injector RJ45 Port Pin Assignments PIN NO 10BASE-T 1000BASE-T 100BASE-TX A.4 1 TX+ DC- DA+ DC- 2 TX- DC- DA- DC- 3 RX+ DC+ DB+ DC+ 4 - DC+ DC+ DC+ 5 - DC+ DC- DC+ 6 RX- DC+ DB- DC+ 7 - DC- DD+ DC- 8 - DC0 DD- DC0 RJ45 Pin Assignment of Non-802.3af/802.3at Standard PD with PoE Mid-span PD Pin out of Cisco non-802.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 APPENDIX B. B.1 Recommended Use of the Connected Wires (Applicable to the system with voltage attenuation less than 3%) The following table is applicable to the applications in the system. Distance in feet ( meters ) Amps 24 AWG 22 AWG 20 AWG 18 AWG 2.5 5.6 ft (1.95m) 8.8 ft (2.70m) 14.12 ft (4.30m) 22.50 ft (6.86m) 36.0 ft (11.0m) 56.4 ft (17.22m) 5.0 2.80 ft (0.86m) 4.4 ft (1.36m) 7.5 1.86 ft (0.
Industrial Renewable Energy 4-Port 10/100/1000T 802.3at PoE+ Managed Ethernet Switch BSP-360 Description Specifications LVD (Low Voltage Disconnection) 22.2V DC (21.0~25.0V) LVR (Low Voltage Reconnection) 24.8V DC (23.0~27.