ADE-4120 ADSL Firewall Router User’s Manual
Copyright Copyright (C) 2004 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Table of Contents CHAPTER 1. INTRODUCTION .............................................................................................................................. 1 1.1 AN OVERVIEW OF THE ADE-4120 .................................................................................................................... 1 1.2 PACKAGE CONTENTS ...................................................................................................................................... 1 1.3 ADE-4120 FEATURES ..........
APPENDIX B. FAQ AND PRODUCT SUPPORT................................................................................................. 36 APPENDIX C GLOSSARY ...................................................................................................................................
Chapter 1. Introduction 1.1 An Overview of the ADE-4120 The ADE-4120 ADSL Firewall Router provides office and residential users the ideal solution for securely sharing a high-speed ADSL broadband Internet connection on a 10/100Mbps Fast Ethernet backbone. It has built-in 4-port 10/100Mbps Ethernet switch for easily connecting to multiple PCs. They can support downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1Mbps. It is compliant with Multi-Mode standard (ANSI T1.
PLANET ADE-4120 ADSL Firewall Router LAN site and automatic switching between MDI and MDI-X for 10Base-T and 100BaseTX ports is supported. Multi-Protocol to Establish A Connection: Supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed) and PPP over Ethernet (RFC 2516) to establish a connection with the ISP. The product also supports VC-based and LLC-based multiplexing.
Chapter 1 Introduction 1.4 ADE-4120 Application Internet Connection with Firewall: They are the perfect solution to connect a small group of PCs to a high-speed broadband Internet connection. Multi-users can have high-speed Internet access simultaneously. With their packet filter and access control function, the internal network is greatly secured.
Chapter 2. Using the Router 2.1 Cautions for using the ADE-4120 Do not place the ADE-4120 under high humidity and high temperature. Do not use the same power source for ADE-4120 with other equipment. Do not open or repair the case yourself. If the ADE-4120 is too hot, turn off the power immediately and have a qualified serviceman repair it. Place the ADE-4120 on a stable surface. Only use the power adapter that comes with the package. 2.
Chapter 2 Using ADE-4120 2.3 The Rear Ports ADE-4120 Port ADSL CONSOLE LAN 1 — 4 (RJ-45 connector) Meaning Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. Connect a RS-232 cable to this port when connecting to a PC’s RS-232 port (9-pin serial port). Connect an UTP Ethernet cable to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps.
Chapter 3. Configuration The ADE-4120 can be configured with your Web browser. The web browser is included as a standard application in the following operation systems, UNIX, Linux, Mac OS, Windows 98/NT/2000/Me, etc. The product provides a very easy and user-friendly interface for configuration. 3.1 Before Configuration This section describes the configuration required by LAN-attached PCs that communicate with the ADE-4120, either to configure the device, or for network access.
Chapter 2 Using ADE-4120 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties. 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button.
PLANET ADE-4120 ADSL Firewall Router 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click “OK” to finish the configuration.
Chapter 2 Using ADE-4120 3.3.2 For Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
PLANET ADE-4120 ADSL Firewall Router 3.3.3 For Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties.
Chapter 2 Using ADE-4120 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
PLANET ADE-4120 ADSL Firewall Router 3.3.4 For Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2. Double-click Local Area Connection 3. In the LAN Area Connection Status window, click Properties.
Chapter 2 Using ADE-4120 4. Select Internet Protocol (TCP/IP) and click Properties. 5.
PLANET ADE-4120 ADSL Firewall Router 6. Click OK to finish the configuration. 3.4 Factory Default Settings Before configurating this ADE-4120, you need to know the following default settings. 1. Web Configurator Does not require user name and password 2. Device IP Network settings in LAN site IP Address : 192.168.1.254 Subnet Mask : 255.255.255.0 3. ISP setting in WAN side Bridge (RFC1483 bridge) 4. DHCP server DHCP server is enabled. Start IP Address : 192.168.1.1 End IP Address : 192.168.1.100 3.4.
Chapter 2 Using ADE-4120 are shown below. LAN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 WAN Port The Bridge function is enabled by default. Enabled DHCP server function IP addresses for distribution to PCs 100 IP addresses continuing from 192.168.1.1 through 192.168.1.100 (Actually, it can support up to 253 users.) 3.
PLANET ADE-4120 ADSL Firewall Router 3.6 Configuring with the Web Browser Open the web browser, enter the local port IP address of this ADE-4120 , which defaults at 192.168.1.254, and click “Go”, you will get a function overview page when login successfully. 3.6.1 Home At the “Home” function page, the top navigation pane provides links to the desired setup page. The left navigation pane provides the detail explanations of the available configuration of each option on the top pane.
Chapter 2 Using ADE-4120 3.6.2.1 Setup 1 System parameters Select the operating mode in Setup1 page of web configuration server as follows: You can get these modes from your ISP. Please check section 3.5 for detail. After you select the mode you want, please click “Next” to continue. 3.6.2.2 Setup 2 LAN parameters Configure the following values into the ADSL Router's Setup page. Not everyone will require the following settings. Check with your ISP.
PLANET ADE-4120 ADSL Firewall Router creating with your ADSL Router. Unless you have specific internal needs or in the router mode, there should be no reason to change these values. Please check with your ISP to see if you need to enter Router & Domain Names to be viewed by your ISP's network. If you do, click on your Start button. Choose Control Panel, then double-click the Network icon. Choose the Identification tab. There will be a Computer Name and a Workgroup name displayed here.
Chapter 2 Using ADE-4120 3.6.2.4 Setup 4 VC parameters You should check with your ISP for VPI/VCI and AAL5 Encapsulation for ATM VC parameter. After you complete the settings of this page, click “Next” to continue. 3.6.2.5 Setup 5 Dial parameters You should give user's name and password if you select PPPoE+NAT or PPPoA+NAT mode in step 1. If you select other mode, this page will not show. Click “Next” to continue.
PLANET ADE-4120 ADSL Firewall Router 3.6.2.6 Step 6 Confirm parameters This page shows all the settings you have configured. Please click “Finish” button to complete your settings. The “Save Configuration & Restart System” page is shown. Click “Save” to save the new configuration. The router will restart automatically.
Chapter 2 Using ADE-4120 3.6.3 Basic The basic configurations are listed these functions in common use for the ADSL Router system. Please link to the specific feature page to set these parameters. 3.6.3.1 User profile This page allows you to set the Username and Password to prevent improper accessing from un-authorized users. It also allows you to enable or disable remote management.
PLANET ADE-4120 ADSL Firewall Router 3.6.3.2 Log table display setting The packet log setting allows the display of the incoming and outgoing data on the MONITOR. Check the box to enable log table then you can find the record on the “Monitor”. 3.6.3.3 Packet filter The router provides two filter functions: LAN to WAN and WAN to LAN. Please click the function you need. If you select LAN to WAN, you can add the IP address, IP range, Port range, Mac address of the local PC to access the Internet.
Chapter 2 Using ADE-4120 3.6.3.4 User access control You can fill in the LAN IP address, MAC address and port range to limit the Internet access of the local user. 3.6.3.5 DHCP DHCP (Dynamic Host Configuration Protocol) allows you to automatically assign IP addresses to client stations logging onto a TCP/IP network. It eliminates the need to manually assign permanent IP addresses. This ADSL router also allows host with fixed IP. You can key in the host MAC Address in the table below.
PLANET ADE-4120 ADSL Firewall Router 3.6.3.6 Forward This page allows you to setup up the public services on your network. It provides three sub-functions: Virtual Server, Prot forwarding and Port Triggering. 3.6.3.6.1 Virtual Server Please fill in the IP address and enable the server. The Preset Applications are among the most widely used Internet applications. 3.6.3.6.2 Port Forwarding Please select the Network service protocol type, fill in the service parameters and enable this service.
Chapter 2 Using ADE-4120 3.6.3.6.3 Port Triggering The Router will watch the outgoing data for specific port. If the PC behind the router sends the data witch is matching the 'Port Triggering table' through the router, the router will record it. When the requested incoming data returns, the router will send it to the PC by way of Port Triggering table rule. 3.6.3.
PLANET ADE-4120 ADSL Firewall Router helps you dividing the client PCs on the LAN into several groups and each group access Internet through one real IP Address. You also can set single local IP Address map to single Global IP Address. Thus it empowers the management and provides much wider application over ADSL line. 3.6.3.8 DMZ You can set one DMZ host in the DMZ parameter to expose all ports of the internal user to the Internet.
Chapter 2 Using ADE-4120 3.6.3.9 DDNS DDNS(Dynamic DNS) service points a fixed hostname to a dynamic WAN IP address or static IP address, allowing your computer to be accessed from various locations on the Internet without knowing your current IP. With a DDNS connection you can host your own web site, email server, FTP site and more at your own location. The DDNS service is provided by DynDNS.org, you need to register a domain name in www.dyndns.org before configuring DDNS.
PLANET ADE-4120 ADSL Firewall Router 3.6.4 Advance This function allows you to make routing configuration. 3.6.4.1 Static route You may set up a static route if you want to connect your router to more than one network. A static route is a pre-determined path that network information must reach a specific host or network.
Chapter 2 Using ADE-4120 3.6.4.2 RIP RIP (Routing Information Protoco allows a router to exchange routing information with other routers. The RIP Direction field controls the sending and receiving of RIP packets. The RIP version field controls the format and the broadcasting method of the RIP packets that the Router sends (it recognizes both formats when receiving). RIP-1 is universally supported, but RIP-2 carries more information.
PLANET ADE-4120 ADSL Firewall Router 3.6.5 Utility This function provides you the system information, status and firmware upgrade. 3.6.5.1 System This page provides you the general system information including firmware version.
Chapter 2 Using ADE-4120 3.6.5.2 Firmware upgrade This page allows you to upgrade the firmware through TFTP server. Please note that you have to setup a TFTP server first and store that firmware file on the TFTP server directory. After you have clicked on the 'OK' button, please wait for a while during the transfer of the files. Please note that if you upgrade the "All images", it will take almost two minutes. The LED light will flash until the upgrade is finished.
PLANET ADE-4120 ADSL Firewall Router Router is restarted, your browser session will be disconnected. It may appear that your browser session doesn't work. When the ADSL Router restarts after a few seconds, you can input the default IP address ( http://192.168.1.254) to open the web interface again. 3.6.5.4 Save & Restart This page offers you the opportunity to save new configurations and restart your router. To update the configuration, the server must be restarted.
Chapter 2 Using ADE-4120 3.6.6 Monitor This function is used to monitor the Network status or the status of the ADSL Router. The available options depend on your operation mode. Click on the icon in the left window then the table will pop up.
PLANET ADE-4120 ADSL Firewall Router Chapter 4. Troubleshooting If the ADE-4120 ADSL Firewall Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save you time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the ADE-4120 Problem None of the LEDs are on when you turn on the ADE-4120 Corrective Action Check the connection between the adapter and the ADE-4120 .
Appendix A. Specification Product Model Hardware Standard Protocol Interoperability Ports LAN WAN LED Indicators Button Console Software Protocol Security ADSL Firewall Router ADE-4120A / ADE-4120B ANSI T1.413 Issue 2 ITU G.992.1 (G.dmt) including - Annex A (ADSL over POTS for ADE-4120A) - Annex B (ADSL over ISDN for ADE-4120B) G.992.2 (G.
Appendix B. FAQ and Product Support Most problems can be solved by using the Troubleshooting in Chapter 4 and the following FAQ. If you cannot resolve the problem, please contact the dealer where you purchased this product. For any other questions, please contact PLANET directly at the following email address: support@planet.com.tw. You can also download upgraded driver or software utilities for free from PLANET’s website at http://www.planet.com.
How do I get Napster to work with the Router? Napster is fully compatible with the Router and requires no special settings. How can I not receive corrupted FTP downloads? If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP program. Web page hangs, corrupt downloads, or nothing but junk characters is being displayed on the screen.
Why can't I connect to the Web Configurator? You can remove the proxy server settings in your web browser. Why is that i can ping to outside hosts, but not access Internet websites? Check the DNS server settings on your PC. You should get the DNS servers settings from your ISP. If your PC is running a DHCP client, remove any DNS IP address setting. As the router will assign the DNS settings to the DHCP-client-enabled PC.
Appendix C Glossary Address mask A bit mask used to select bits from an Internet address for subnet addressing. The mask is 32 bits long and selects the network portion of the Internet address and one or more bits of the local portion. Sometimes called subnet mask. AAL5 ATM Adaptation Layer - This layer maps higher layer user data into ATM cells, making the data suitable for transport through the ATM network.
every device on your network. DHCP software typically runs in servers and is also found in network devices such as Routers. DMT Discrete Multi-Tone frequency signal modulation Downstream rate The line rate for return messages or data transfers from the network machine to the user's premises machine. DSLAM Digital Subscriber Line Access Multiplex Dynamic IP Addresses A dynamic IP address is an IP address that is automatically assigned to a client station (computer, printer, etc.) in a TCP/IP network.
Internet address An IP address is assigned in blocks of numbers to user organizations accessing the Internet. These addresses are established by the United States Department of Defense's Network Information Center. Duplicate addresses can cause major problems on the network, but the NIC trusts organizations to use individual addresses responsibly. Each address is a 32-bit address in the form of x.x.x.x where x is an eight- bit number from 0 to 255.
on connection by simulating a dial-up connection. Remote server A network computer allows a user to log on to the network from a distant location. RFC Request for Comments - Refers to documents published by the Internet Engineering Task Force (IETF) proposing standard protocols and procedures for the Internet. RFCs can be found at www.ietf.org.. Route The path that network traffic takes from its source to its destination. The route a datagram may follow can include many gateways and many physical networks.
accessed by multiple users, such as Server PCs, or printers. If you are using your Router to share your cable or DSL Internet connection, contact your ISP to see if they have assigned your home a static IP address. You will need that address during your Router's configuration. Subnet For routing purposes, IP networks can be divided into logical subnets by using a subnet mask. Values below those of the mask are valid addresses on the subnet.