ADSL 2/2+ VoIP Router IAD-200, IAD-200W User's Manual
Copyright Copyright (C) 2005 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) This Device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment.
Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies. Safety This equipment is designed with the utmost care for the safety of those who install and use it.
Table of Contents CHAPTER 1 INTRODUCTION..................................................................... 1 IAD-200 / IAD-200W Features ................................................................. 1 Package Contents ....................................................................................... 4 Physical Details........................................................................................... 5 CHAPTER 2 INSTALLATION ................................................................
Routing ...................................................................................................... 85 Upgrade Firmware................................................................................... 89 CHAPTER 7 OPERATION AND STATUS ................................................ 90 Operation .................................................................................................. 90 Status Screen ......................................................................................
Chapter 1 Introduction 1 This Chapter provides an overview of the ADSL 2/2+ VoIP router (IAD-200) / 802.11g ADSL 2/2+ VoIP router's (IAD-200W) features and capabilities. Congratulations on the purchase of your new ADSL 2/2+ VoIP router – IAD-200 / 802.11g ADSL 2/2+ VoIP router – IAD-200W. The IAD-200 / IAD-200W is a multi-function device providing the following services: • • • • • ADSL 2/2+ Modem. Shared Broadband Internet Access (NAT Router) for all LAN & WLAN users. Wireless Access Point for 802.
• Auto-detection of Internet Connection Method. In must situations, the IAD-200 / IAD-200W can test your ADSL and Internet connection to determine the connection method used by your ISP. • Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the IAD-200 / IAD-200W supports both Dynamic IP Address (IP Address is allocated on connection) and Fixed IP Address. Advanced Internet Functions • Application Level Gateways (ALGs).
• WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key sizes of 64 Bit and 128 Bit are supported. WEP encrypts any data before transmission, providing protection against snoopers. • WPA-PSK support. Like WEP, WPA-PSK encrypts any data before transmission, providing protection against snoopers. The WPA-PSK is a later standard than WEP, and provides both easier configuration and greater security than WEP. • Wireless MAC Access Control.
Package Contents The following items should be included. If any of these items are damaged or missing, please contact your dealer immediately. • The IAD-200 / IAD-200W Unit • 1 Cat-5 Ethernet (LAN) cable • 1 RJ-11 (ADSL) cable • Power Adapter • Quick Installation Guide • CD-ROM containing the on-line manual.
Physical Details Front-mounted LEDs IAD-200 IAD-200W Figure 2: Front Panel Power LED (Green) On - Power on. Status LED (Yellow) Off - Normal operation. LAN • 100BT - This will be ON if the LAN connection is using 100BaseT, and Blinking if data is being transferred via the LAN port. • 10BT - This will be ON if the LAN connection is using 10BaseT, and Blinking if data is being transferred via the LAN port. Off - No power. Blinking - This LED blinks during start up, and during a Firmware Upgrade.
Internet On - Internet connection is available. Off - No Internet connection available. Flashing - Data is being transmitted or received.
Rear Panel IAD-200 IAD-200W Figure 3: Rear Panel ADSL port Connect this port to your ADSL line. PSTN Connect this to your PSTN line (normal analog phone line). Phone Connect a standard phone here. LAN Connect this port to your hub, using the supplied LAN cable. Reset Button (Reset to Defaults) This button will reset the IAD-200 / IAD-200W to the factory default settings.
2 Chapter 2 Installation This Chapter covers the physical installation of the ADSL 2/2+ VoIP router (IAD-200) / 802.11g ADSL 2/2+ VoIP router (IAD-200W). Requirements • TCP/IP protocol must be installed on all PCs. • To use the Wireless Access Point, all Wireless devices must be compliant with the IEEE 802.11g or IEEE 802.11b specifications. • For Internet Access, an ADSL service and ISP account. • For VoIP, a SIP account with a VoIP service provider. Procedure Figure 4: Installation Diagram 1.
2. Connect LAN Cable Use the supplied LAN cable to connect the LAN port on the IAD-200 / IAD-200W to your hub. 3. Connect ADSL Cable Connect the supplied ADSL cable from the ADSL port on the IAD-200 / IAD-200W to the ADSL terminator provided by your phone company. 4. Connect PSTN Line Connect the PSTN socket on the rear of the IAD-200 / IAD-200W to your normal phone line socket. 5. Connect Phone Connect a standard phone to the Phone socket on the rear of the IAD-200 / IAD-200W. 6.
3 Chapter 3 Setup This Chapter provides Setup details of the IAD-200 / IAD-200W. Overview This chapter describes the setup procedure for: • Internet Access • LAN configuration • Wireless setup • Assigning a Password to protect the configuration data. PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC Configuration. Other configuration may also be required, depending on which features and functions of the IAD-200 / IAD-200W you wish to use.
Configuration Program The IAD-200 / IAD-200W contains an HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Your Browser must support JavaScript. The configuration program has been tested on the following browsers: • Netscape 7.1 or later. • Mozilla 1.6 or later • Internet Explorer V5.5 or later Preparation Before attempting to configure the IAD-200 / IAD-200W, please ensure that: • Your PC can establish a physical connection to the IAD-200 / IAD-200W.
If you cannot connect If the IAD-200 / IAD-200W does not respond, check the following: • The IAD-200 / IAD-200W is properly installed, LAN connection is OK, and it is powered ON. You can test the connection by using the "Ping" command: • Open the MS-DOS window or command prompt window. • Enter the command: ping 192.168.0.1 If no response is received, either the connection is not working, or your PC's IP address is not compatible with the IAD-200 / IAD-200W's IP Address. (See next item.
Common Connection Types Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. a) ADSL parameters (VPI and VCI) may be required, if they cannot be detected automatically. b) Some ISP's may require you to use a particular Hostname or Domain name, or MAC (physical) address. Static (Fixed) IP Address PPPoE, PPPoA Your ISP allocates a permanent IP Address to you. Usually, the connection is "Always on".
Home Screen After finishing the Setup Wizard, you will see the Home screen. When you connect in future, you will see this screen when you connect. An example screen is shown below. Figure 5: Home Screen Main Menu The main menu, on the left, contains links to the most-commonly used screen. To see the links to the other available screens, click "Advanced" or "Administration". The main menu also contains two (2) buttons: • Log Out - When finished, you should click this button to logout.
LAN Screen Use the LAN link on the main menu to reach the LAN screen. An example screen is shown below. Figure 6: LAN Screen Data - LAN Screen TCP/IP IP Address IP address for the IAD-200 / IAD-200W, as seen from the local LAN. Use the default value unless the address is already in use or your LAN is using a different IP address range. In the latter case, enter an unused IP Address from within the range used by your LAN. Subnet Mask The default value 255.255.255.
• The DHCP Server provides the Gateway and DNS addresses to the client, as well as allocating an IP Address. • The IAD-200 / IAD-200W can act as a DHCP server. • Windows 95/98/ME and other non-Server versions of Windows will act as a DHCP client. This is the default Windows setting for the TCP/IP network protocol. However, Windows uses the term Obtain an IP Address automatically instead of "DHCP Client". • You must NOT have two (2) or more DHCP Servers on the same LAN segment.
Wireless Screen (IAD-200W only) The IAD-200W's settings must match the other Wireless stations. Note that the IAD-200W will automatically accept both 802.11b and 802.11g connections, and no configuration is required for this feature. To change the IAD-200W's default settings for the Wireless Access Point feature, use the Wireless link on the main menu to reach the Wireless screen. An example screen is shown below.
SSID This is also called the "Network Name". Enter the desired value. The default value is Wireless. • If using an ESS (Extended Service Set, with multiple access points) this ID is called an ESSID (Extended Service Set Identifier). • To communicate, all Wireless stations use the same SSID/ESSID, so must match the value entered here. Options Mode Select the desired mode: • Channel No. Broadcast SSID 802.11G-plus (TI) This allows clients to use any of the following modes: • Standard 802.
Allow access by … Use this feature to determine which Wireless stations can use the Access Point. The options are: • All Wireless Stations - All wireless stations can use the access point, provided they have the correct SSID and security settings. • Set Stations Button Trusted Wireless stations only - Only wireless stations you designate as "Trusted" can use the Access Point, even if they have the correct SSID and security settings. This feature uses the MAC address to identify Wireless stations.
Wireless Security (IAD-200W only) This screen is accessed by clicking the "Configure" button on the Wireless screen. There are 3 options for Wireless security: • Disabled - no data encryption is used. • WEP - data is encrypted using the WEP standard. • WPA-PSK - data is encrypted using the WPA-PSK standard. This is a later standard than WEP, and provides much better security than WEP. If all your Wireless stations support WPA-PSK, you should use WPA-PSK rather than WEP.
Key Value Enter the key value or values you wish to use. The Default Key is required, the other keys are optional. Other stations must have the same key. Passphrase If desired, you can generate a key from a phrase, instead of entering the key value directly. Enter the desired phrase, and click the "Generate Keys" button. WPA-PSK Wireless Security Figure 9: WPA-PSK Data - WPA-PSK Screen Security System WPA-PSK PSK Enter the PSK (network key).
Trusted Wireless Stations (IAD-200W only) This feature can be used to prevent unknown Wireless stations from using the Access Point. This list has no effect unless the setting Allow access by trusted stations only is enabled. To change the list of trusted wireless stations, use the Modify List button on the Access Control screen. You will see a screen like the sample below.
Edit Use this to change an existing entry in the "Trusted Stations" list: 1. Select the Station in the Trusted Station list. 2. Click the Edit button. The address will be copied to the "Address" field, and the Add button will change to Update. 3. Edit the address (MAC or physical address) as required. 4. Click Update to save your changes. Add (Update) To add a Trusted Station which is not in the "Other Wireless Stations" list, enter the required data and click this button.
Password Screen The password screen allows you to assign a password to the IAD-200 / IAD-200W. Figure 11: Password Screen Old Password Enter the existing password in this field. New password Enter the new password here. Verify password Re-enter the new password here. You will be prompted for the password when you connect, as shown below. Figure 12: Password Dialog • The "User Name" is always admin • Enter the password for the IAD-200 / IAD-200W, as set on the Password screen above.
Chapter 4 PC Configuration 4 This Chapter details the PC Configuration required on the local ("Internal") LAN. Overview For each PC, the following may need to be configured: • TCP/IP network settings • Internet Access configuration • Wireless configuration Windows Clients This section describes how to configure Windows clients for Internet access via the IAD-200 / IAD-200W. The first step is to check the PC's TCP/IP settings.
Checking TCP/IP Settings - Windows 9x/ME: 1. Select Control Panel - Network. You should see a screen like the following: Figure 13: Network Configuration 2. 3. Select the TCP/IP protocol for your network card. Click on the Properties button. You should then see a screen like the following. Figure 14: IP Address (Win 95) Ensure your TCP/IP settings are correct, as follows: Using DHCP To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting.
• On the Gateway tab, enter the IAD-200 / IAD-200W's IP address in the New Gateway field and click Add, as shown below. Your LAN administrator can advise you of the IP Address they assigned to the IAD-200 / IAD-200W. Figure 15: Gateway Tab (Win 95/98) • On the DNS Configuration tab, ensure Enable DNS is selected. If the DNS Server Search Order list is empty, enter the DNS address provided by your ISP in the fields beside the Add button, then click Add.
Checking TCP/IP Settings - Windows NT4.0 1. Select Control Panel - Network, and, on the Protocols tab, select the TCP/IP protocol, as shown below. Figure 17: Windows NT4.0 - TCP/IP 2. Click the Properties button to see a screen like the one below.
Figure 18: Windows NT4.0 - IP Address 3. 4. Select the network card for your LAN. Select the appropriate radio button - Obtain an IP address from a DHCP Server or Specify an IP Address, as explained below. Obtain an IP address from a DHCP Server This is the default Windows setting. Using this is recommended. By default, the IAD-200 / IAD-200W will act as a DHCP Server. Restart your PC to ensure it obtains an IP Address from the IAD-200 / IAD-200W.
Figure 19 - Windows NT4.0 - Add Gateway 2. The DNS should be set to the address provided by your ISP, as follows: • Click the DNS tab. • On the DNS screen, shown below, click the Add button (under DNS Service Search Order), and enter the DNS provided by your ISP. Figure 20: Windows NT4.
Checking TCP/IP Settings - Windows 2000: 1. 2. Select Control Panel - Network and Dial-up Connection. Right - click the Local Area Connection icon and select Properties. You should see a screen like the following: Figure 21: Network Configuration (Win 2000) 3. 4. Select the TCP/IP protocol for your network card. Click on the Properties button. You should then see a screen like the following.
5. Ensure your TCP/IP settings are correct, as described below. Using DHCP To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. Using this is recommended. By default, the IAD-200 / IAD-200W will act as a DHCP Server. Restart your PC to ensure it obtains an IP Address from the IAD-200 / IAD-200W.
Checking TCP/IP Settings - Windows XP 1. 2. Select Control Panel - Network Connection. Right click the Local Area Connection and choose Properties. You should see a screen like the following: Figure 23: Network Configuration (Windows XP) 3. 4. Select the TCP/IP protocol for your network card. Click on the Properties button. You should then see a screen like the following.
Figure 24: TCP/IP Properties (Windows XP) 5. Ensure your TCP/IP settings are correct. Using DHCP To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. Using this is recommended. By default, the IAD-200 / IAD-200W will act as a DHCP Server. Restart your PC to ensure it obtains an IP Address from the IAD-200 / IAD-200W.
Internet Access To configure your PCs to use the IAD-200 / IAD-200W for Internet access: • Ensure that the Internet connection is functional. • Use the following procedure to configure your Browser to access the Internet via the LAN, rather than by a Dial-up connection. For Windows 9x/ME/2000 1. 2. 3. 4. 5. 6. 7. Select Start Menu - Settings - Control Panel - Internet Options. Select the Connection tab, and click the Setup button.
Macintosh Clients From your Macintosh, you can access the Internet via the IAD-200 / IAD-200W. The procedure is as follows. 1. Open the TCP/IP Control Panel. 2. Select Ethernet from the Connect via pop-up menu. 3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field can be left blank. 4. Close the TCP/IP panel, saving your settings.
Wireless Station Configuration (IAD-200W only) This section applies to all Wireless stations wishing to use the IAD-200W's Access Point, regardless of the operating system which is used on the client. To use the Wireless Access Point in the IAD-200W, each Wireless Station must have compatible settings, as follows: Mode The mode must be set to Infrastructure (rather than Ad-hoc) Access points only operate in Infrastructure mode. SSID (ESSID) This must match the value used on the IAD-200W.
Figure 26 Wireless Networks (Windows XP) If the "Broadcast SSID" setting on the IAD-200W has been disabled, its SSID will NOT be listed. See the following section "If the SSID is not listed" for details of dealing with this situation. 4. The next step depends on whether or not Wireless security has been enabled on the IAD200W. If Wireless Security is Disabled If Wireless security on the IAD-200W is disabled, Windows will warn you that the Wireless network is not secure.
To connect: • Check the checkbox Allow me to connect to the selected wireless network, even though it is not secure. • The Connect button will then be available. Click the Connect button, and wait a few seconds for the connection to be established. If using WEP Data Encryption If WEP data encryption has been enabled on the IAD-200W, Windows will detect this, and show a screen like the following.
Figure 29: Advanced - Wireless Networks Select the SSID for the IAD-200W, and click Configure, to see a screen like the following: Figure 30: Wireless Network Properties - WEP Configure this screen as follows: • Set Network Authentication to match the IAD-200W. (If the setting on the IAD-200W is "Auto", then either Open or Shared can be used.) • For Data Encryption, select WEP.
• For the Network key and Confirm network key, enter the default key value used on the IAD-200W. (Windows will determine if 64bit or 128bit encryption is used.) • The Key index must match the default key index on the IAD-200W. The default value is 1. • Ensure the options. The key is provided for me automatically and this is a computer-tocomputer (ad hoc) network are unchecked. • Click OK to save and close this dialog.
If using WPA-PSK Data Encryption (IAD-200W only) If WPA-PSK data encryption has been enabled on the IAD-200W, it does not matter which network is selected on the screen below. Just click the Advanced button. Figure 32: Wireless Networks (Windows XP) You will then see a screen like the example below.
Figure 34: Wireless Network Properties- WPA-PSK Configure this screen as follows: • Set Network Authentication to WPA-PSK. • For Data Encryption, select TKIP. • For the Network key and Confirm network key, enter the network key (PSK) used on the IAD-200W. • Ensure the option. This is a computer-to-computer (ad hoc) network is unchecked. • Click OK to save and close this dialog. • This wireless network will now be listed in Preferred Networks on the screen below.
Figure 35: Preferred Networks Click OK to establish a connection to the IAD-200W. If the SSID is not listed (IAD-200W only) If the "Broadcast SSID" setting on the IAD-200W has been disabled, its SSID will NOT be listed on the screen below. Figure 36: Wireless Networks (Windows XP) In this situation, you need to obtain the SSID from your network administrator, and then follow this procedure: 1. Click the Advanced button to see a screen like the example below.
Figure 37: Unlisted Wireless Network 2. Click the Add button. You will see a screen like the example below. Figure 38: Add Wireless Network 3. Configure this screen as follows: • Enter the correct SSID, as used on the IAD-200W. Remember the SSID is casesensitive, so be sure to match the case, not just the spelling. • Set Network Authentication and Data Encryption to match the IAD-200W.
4. • If using data encryption (WEP or WPA-PSK), enter the key used on the IAD-200W. See the preceding sections for details of WEP and WPA-PSK. • Uncheck the options. The key is provided for me automatically and this is a computerto-computer (ad hoc) network. • Click OK to save and exit. This wireless network will then be listed in Preferred Networks on the screen below. Figure 39: Preferred Networks 5. Click OK to establish a connection to the IAD-200W.
Chapter 5 Advanced Features 5 This Chapter explains when and how to use the IAD-200 / IAD-200W's "Advanced" Features. Overview The following advanced features are provided: • Internet: • DMZ • Special Applications • URL filter • Dynamic DNS • Firewall Rules • Firewall Services • Options • Schedule • Virtual Servers • VoIP Internet This screen provides access to the DMZ, Special Applications and URL Filter features.
DMZ This feature, if enabled, allows the DMZ computer on your LAN to be exposed to all users on the Internet. • This allows almost any application to be used on the "DMZ PC". • The "DMZ PC" will receive all "Unknown" connections and data. • If the DMZ feature is enabled, you must select the PC to be used as the "DMZ PC". The "DMZ PC" is effectively outside the Firewall, making it more vulnerable to attacks. For this reason, you should only enable the DMZ feature when required.
Data - Special Applications Screen Checkbox Use this to Enable or Disable this Special Application as required. Name Enter a descriptive name to identify this Special Application. Incoming Ports Outgoing Ports • Type - Select the protocol (TCP or UDP) used when you receive data from the special application or service. (Note: Some applications use different protocols for outgoing and incoming data).
Figure 42: URL Filter Screen Data - URL Filter Screen Current Filter Strings Current Filter Strings Add Filter String The list contains the current list of items to block. • To add to the list, use the "Add" option below. • To delete an entry, select it and click Delete button. • To delete all entries, click the Delete All button. To add to the current list, type the word or domain name you want to block into the field provided, then click the Add button.
Trusted PC Allow Trusted PC Enable this to allow one computer to have unrestricted access to the Internet. For this PC, the URL filter will be ignored. If enabled, you must select the PC to be the trusted PC. Trusted PC Select the PC to be the Trusted PC.
Dynamic DNS (Domain Name Server) This free service is very useful when combined with the Virtual Server feature. It allows Internet users to connect to your Virtual Servers using a URL, rather than an IP Address. This also solves the problem of having a dynamic IP address. With a dynamic IP address, your IP address may change whenever you connect, which makes it difficult to connect to you. DDNS Services work as follows: 1. 2. 3. 4. 5.
DDNS Data Host Name Enter the domain name allocated to you by the DDNS Service. If you have more than one name, enter the name you wish to use. User Name Enter your Username for the DDNS Service. (TZO.com uses your Email address.) Password Enter your current password for the DDNS Service. (TZO.com calls this a key.) Domain Name Enter the domain name allocated to you by the DDNS Service. If you have more than one name, enter the name you wish to use.
Firewall Rules The Firewall Rules screen allows you to define "Firewall Rules" which can allow or prevent certain traffic. "Traffic" means incoming connection attempts, not packets. By default: • All Outgoing traffic is permitted. • All Incoming traffic is denied. Because of this default behavior, any Outgoing rules will generally Block traffic, and Incoming rules will generally Allow traffic. Firewall Rules Screen An example screen is shown below.
Action The action performed on connections which are covered by this rule. LAN Server The PC or Server on your LAN to which traffic covered by this rule will be sent. WAN Users The WAN IP address or addresses covered by this rule. Log Indicates whether or not connections covered by this rule should be logged. Buttons Use the Add button to create a new rule. The other buttons - Edit, Move, or Delete - require that a rule be selected first.
Incoming Rules (Inbound Services) This screen is displayed when the "Add" or "Edit" button for Incoming Rules is clicked. Figure 45: Inbound Services Screen Data - Incoming Rules Screen Inbound Services Service Select the desired Service. This determines which packets are covered by this rule. If necessary, you can define a new Service on the "Services" screen, by defining the protocols and port numbers used by the Service.
Log This determines whether packets covered by this rule are logged. Select the desired action. • Always - always log traffic considered by this rule, whether it matches or not. (This is useful when debugging your rules.) • Never - never log traffic considered by this rule, whether it matches or not. • Match - Log traffic only it matches this rule. (The action is determined by this rule.
BLOCK rule. (That is, you wish to allow a subset of traffic which is currently blocked by another rule.) • LAN Users To define the Schedule used in these selections, use the "Schedule" screen. Select the desired option to determine which PCs are covered by this rule: • Any - All PCs are covered by this rule. • Single PC - Only the selected PC is covered by this rule. If selected, you must select the PC.
User-defined Services Services are used when creating Firewall Rules. If you wish to create a firewall rule, but the required service is not listed in the "Service" list, you can use this feature to define the required service or services. Once created, these services will be listed in the "Service" list, and can be used when creating Firewall Rules. Figure 47: Add Services Screen Data - User-defined Services Services Existing Services This lists any Services you have defined.
Add/Edit Service This screen is displayed when the Add or Edit button on the Services screen is clicked. Figure 48 : Add/Edit Service Data - Add/Edit Service Services Name If editing, this shows the current name of the Service. If adding a new service, this will be blank, and you should enter a suitable name. Type Select the protocol used by the Service. Start Port Enter the beginning of the port range used by the Service. Finish Port Enter the end of the port range used by the Service.
Options This screen allows advanced users to enter or change a number of settings. For normal operation, there is no need to use this screen or change any settings. An example Options screen is shown below. Figure 49: Options Screen Data - Options Screen Internet Respond to Ping MTU Size • If checked, the Wireless Router will respond to Ping (ICMP) packets received from the Internet. • If not checked, Ping (ICMP) packets from the Internet will be ignored.
Schedule This Schedule can be used for the Firewall Rules and the URL filter. Figure 50: Schedule Screen Data - Schedule Screen Schedule Day Each day of the week can scheduled independently. Session 1 Session 2 Two (2) separate sessions or periods can be defined. Session 2 can be left blank if not required. Start Time Enter the start using a 24 hr clock. Finish Time Enter the finish time using a 24 hr clock.
light Savings Time adjustment period, and uncheck it at the end of the Daylight Savings period. Use this NTP Server If you prefer to use a particular NTP server as the primary NTP server, check the checkbox "Use this NTP Server" and enter the Server's IP address in the fields provided. If this setting is not enabled, the default NTP Servers are used. Current Time This displays the current time on the IAD-200 / IAD-200W, at the time the page is loaded.
Virtual Servers This feature, sometimes called Port Forwarding, allows you to make Servers on your LAN accessible to Internet users. Normally, Internet users would not be able to access a server on your LAN because: • Your Server does not have a valid external IP Address. • Attempts to connect to devices on your LAN are blocked by the firewall in this device. The "Virtual Server" feature solves these problems and allows Internet users to connect to your servers, as illustrated below.
• To make it easier for Internet users to connect to your Servers, you can use the "DDNS" feature. This allows Internet users to connect to your Servers with a URL, rather than an IP address. This technology works even if your ISP allocates dynamic IP addresses (IP address is allocated upon connection, so it may change each time you connect). Figure 52: Virtual Servers Screen Data - Virtual Servers Screen Servers Servers This lists a number of common Server types.
Note: From the Internet, ALL Virtual Servers have the IP Address allocated by your ISP.
VoIP To use the VoIP feature requires the following: • Standard Phone A standard analogue Phone must be connected to the Phone socket. • VoIP (SIP Server) Account Generally, you will need a SIP Server account from a VoIP service provider. The account details should include the SIP Register address, SIP Proxy address, SIP register port, SIP Proxy port, username, password, and telephone number. (Many providers use the same proxy server for both Proxy and Register.
Figure 53: VoIP Settings VoIP Settings Local Service SIP Local Port This port is used for peer-to-peer (direct) connections to another device, when no SIP server is used. Normally, this should be left at the default value. Any other devices you wish to connect to must use the same port number. SIP - Line 1 Enable Line1 Check this if you wish to connect to a SIP Server. If enabled, you must provide the following data.
SIP register port Enter the port used for "Register" connections to the Server above. Register Expiry Time This sets the "Idle Timeout" for the SIP Server Login. An Idle connection will be terminated after this time period. Enter the desired value. User Name Enter the login name for connections to the SIP Server. Password Enter the password associated with the login name above. Telephone Number Enter the telephone number provided to you by the VoIP Service provider.
Display Name This is the name you chose when you first opened your account. Your "Display Name" will be visible to other individuals with caller ID. If your display name appears as "UNAVAILABLE", either your VoIP account has not been established or your router has been unable to connect to the VoIP Server. Telephone Number The telephone number associated with this line. This is the telephone number other people will use when they call you.
PSTN Settings PSTN Relay PSTN Prefix The PSTN Relay allows certain calls to be diverted to the PSTN link, even though VoIP is working properly. This PSTN prefix means that any number beginning with this prefix will be diverted to PSTN (the prefix itself is deleted, then the remainder of the number is dialed via PSTN). • If the prefix is a single character, that character must be * • If the prefix is multiple characters, all characters after the 1st character must be digits.
Chapter 6 Advanced Administration 6 This Chapter explains the settings available via the "Administration" section of the menu. Overview Normally, it is not necessary to use these screens, or change any settings. These screens and settings are provided to deal with non-standard situations, or to provide additional options for advanced users. The available settings and features are: PC Database This is the list of PCs shown when you select the "DMZ PC" or a "Virtual Server".
PC Database The PC Database is used whenever you need to select a PC (e.g. for the "DMZ" PC). • It eliminates the need to enter IP addresses. • Also, you do not need to use fixed IP addresses on your LAN. However, if you do use a fixed IP address on some devices on your LAN, you should enter details of each such device into the PC database, using the PC Database screen. PC Database Screen An example PC Database screen is shown below.
Data - PC Database Screen Known PCs This lists all current entries. Data displayed is name (IP Address) type. The "type" indicates whether the PC is connected to the LAN. Name If adding a new PC to the list, enter its name here. It is best if this matches the PC's "hostname". IP Address Enter the IP Address of the PC. The PC will be sent a "ping" to determine its hardware address. If the PC is not available (not connected, or not powered On) you will not be able to add it.
PC Database - Advanced This screen is displayed if the "Advanced Administration" button on the PC Database is clicked. It provides more control than the standard PC Database screen. Figure 57: PC Database (Admin) Data - Advanced PC Database Known PCs This lists all current entries. Data displayed is name (IP Address) type. The "type" indicates whether the PC is connected to the LAN. PC Properties Name If adding a new PC to the list, enter its name here. It is best if this matches the PC's "hostname".
IP Address MAC Address Select the appropriate option: • Automatic - The PC is set to be a DHCP client (Windows: "Obtain an IP address automatically"). The IAD-200 / IAD-200W will allocate an IP address to this PC when requested to do so. The IP address could change, but normally won't. • DCHP Client - Reserved IP Address - Select this if the PC is set to be a DCHP client, and you wish to guarantee that the IAD-200 / IAD-200W will always allocate the same IP Address to this PC.
Config File This feature allows you to download the current settings from the IAD-200 / IAD-200W, and save them to a file on your PC. You can restore a previously-downloaded configuration file to the IAD-200 / IAD-200W, by uploading it to the IAD-200 / IAD-200W. This screen also allows you to set the IAD-200 / IAD-200W back to its factory default configuration. Any existing settings will be deleted. An example Config File screen is shown below.
Logs The Logs record various types of activity on the IAD-200 / IAD-200W. This data is useful for troubleshooting, but enabling all logs will generate a large amount of data and adversely affect performance. Since only a limited amount of log data can be stored in the IAD-200 / IAD-200W, log data can also be E-mailed to your PC. Use the E-mail screen to configure this feature. Figure 59: Logs Screen Data - Logs Screen Logs Current Time The current time on the IAD-200 / IAD-200W is displayed.
Buttons There are three (3) buttons • Refresh - Update the log data. • Clear Log - Clear the log, and restart it. This makes new messages easier to read. • Send Log - E-mail the log immediately. This is only functional if the E-mail screen has been configured. Logs Include (Checkboxes) Use these checkboxes to determine which events are included in the log. Checking all options will increase the size of the log, so it is good practice to disable any events which are not really required.
E-mail This screen allows you to E-mail Logs and Alerts. A sample screen is shown below. Figure 60: E-mail Screen Data - E-mail Screen E-Mail Notification Turn E-mail Notification on Check this box to enable this feature. If enabled, the E-mail address information (below) must be provided. Send to this Email address Enter the E-mail address the Log is to be sent to. The E-mail will also show this address as the Sender's address.
Password If you have enabled "My SMTP Mail Server requires authentication" above, enter the password required to login to your SMTP Server. E-mail Alerts Send E-mail alerts immediately You can choose to have alerts E-mailed to you, by checking the desired checkboxes.
Diagnostics This screen allows you to perform a "Ping" or a "DNS lookup". These activities can be useful in solving network problems. An example Network Diagnostics screen is shown below. Figure 61: Network Diagnostics Screen Data - Network Diagnostics Screen Ping Ping this IP Address Enter the IP address you wish to ping. The IP address can be on your LAN, or on the Internet. Note that if the address is on the Internet, and no connection currently exists, you could get a "Timeout" error.
Remote Administration If enabled, this feature allows you to manage the IAD-200 / IAD-200W via the Internet. Figure 62: Remote Administration Screen Data - Remote Administration Screen Remote Administration Enable Remote Management Check to allow administration/management via the Internet. (To connect, see below). If Disabled, this device will ignore Administration connection attempts from the Internet.
For security, you should restrict access to as few external IP addresses as practical. To connect from a remote PC via the Internet 1. 2. Ensure your Internet connection is established, and start your Web Browser. In the "Address" bar, enter "HTTP://" followed by the Internet IP Address of the IAD-200 / IAD-200W. If the port number is not 80, the port number is also required. (After the IP Address, enter ":" followed by the port number.) e.g. HTTP://123.123.123.
Routing Overview • If you don't have other Routers or Gateways on your LAN, you can ignore the "Routing" page completely. • If the IAD-200 / IAD-200W is only acting as a Gateway for the local LAN segment, ignore the "Routing" page even if your LAN has other Routers. • If your LAN has a standard Router (e.g. Cisco) on your LAN, and the IAD-200 / IAD200W is to act as a Gateway for all LAN segments, enable RIP (Routing Information Protocol) and ignore the Static Routing table.
Figure 63: Routing Screen Data - Routing Screen RIP RIP Direction Select the desired RIP Direction. RIP Version Choose the RIP Version for the Server. Static Routing Static Routing Table Entries This list shows all entries in the Routing Table. • This area shows details of the selected item in the list. • Change any the properties as required, then click the "Edit" button to save the changes to the selected entry.
Local Router The local router is the Router installed on the same LAN segment as the IAD-200 / IAD-200W. This router requires that the Default Route is the IAD-200 / IAD-200W itself. Typically, routers have a special entry for the Default Route. It should be configured as follows. Destination IP Address Normally 0.0.0.0, but check your router documentation. Network Mask Normally 0.0.0.0, but check your router documentation. Gateway IP Address The IP Address of the IAD-200 / IAD-200W.
Router) Metric 2 Entry 2 (Segment 2) Destination IP Address 192.168.2.0 Network Mask 255.255.255.0 (Standard Class C) Gateway IP Address 192.168.0.100 Metric 3 For Router A's Default Route Destination IP Address 0.0.0.0 Network Mask 0.0.0.0 Gateway IP Address 192.168.0.1 (IAD-200 / IAD-200W's IP Address) For Router B's Default Route Destination IP Address 0.0.0.0 Network Mask 0.0.0.0 Gateway IP Address 192.168.1.
Upgrade Firmware The firmware (software) in the IAD-200 / IAD-200W can be upgraded using your Web Browser. You must first download the upgrade file, then select Upgrade Firmware on the Administration menu. You will see a screen like the following. Figure 65: Router Upgrade Screen To perform the Firmware Upgrade: 1. 2. 3. Click the Browse button and navigate to the location of the upgrade file. Select the upgrade file. Its name will appear in the Upgrade File field.
Chapter 7 Operation and Status 7 This Chapter details the operation of the IAD-200 / IAD-200W and the status screens. Operation Once both the IAD-200 / IAD-200W and the PCs are configured, operation is automatic. However, there are some situations where additional Internet configuration may be required. Refer to Chapter 5 - Advanced Features for further details. Status Screen Use the Status link on the main menu to view this screen.
Figure 66: Status Screen Data - Status Screen System Device Name The current name of the Router. This name is also the "hostname" for users with an "@Home" type connection. Firmware Version The version of the current firmware installed. ADSL Modem Status This indicates the status of the ADSL modem component. DownStream Connection Speed Displays the speed for the DownStream Connection. UpStream Connection Speed If connected, displays the speed for the Up Stream (upload) ADSL Connection.
Internet (VC1) Connection Method Displays the current connection method, as set in the Setup Wizard. Connection Status This indicates the current status of the Internet Connection • Active - Connection exists • Idle - No current connection, but no error has been detected. This condition normally arises when an idle connection is automatically terminated. • Failed - The connection was terminated abnormally. This could be caused by Modem failure, or the loss of the connection to the ISP's server.
devices currently on the network. Refresh Screen Update the data displayed on screen.
Connection Status - PPPoE & PPPoA If using PPPoE (PPP over Ethernet) or PPPoA (PPP over ATM), a screen like the following example will be displayed when the "Connection Details" button is clicked. Figure 67: PPPoE Status Screen Data - PPPoE/PPPoA Screen Connection Time This indicates how long the current connection has been established. PPPoE Link Status This indicates whether or not the connection is currently established.
Connection Details - Dynamic IP Address If your access method is "Direct" (no login), with a Dynamic IP address, a screen like the following example will be displayed when the "Connection Details" button is clicked. Figure 68: Connection Details - Fixed/Dynamic IP Address Data - Dynamic IP address Internet IP Address The current IP Address of this device, as seen by Internet users. This address is allocated by your ISP (Internet Service Provider).
IAD-200 / IAD-200W, clicking the "Renew" button will attempt to re-establish the connection and obtain an IP Address from the ISP's DHCP Server. Close Close this window.
Connection Details - Fixed IP Address If your access method is "Direct" (no login), with a fixed IP address, a screen like the following example will be displayed when the "Connection Details" button is clicked. Figure 69: Connection Details - Fixed/Dynamic IP Address Data - Fixed IP address Screen Internet IP Address The IP Address of this device, as seen by Internet users. This address is allocated by your ISP (Internet Service Provider).
Using VoIP VoIP cannot be used until configuration has been completed. See the VoIP topic in Chapter 5 - Advanced Features for details of VoIP configuration. Normal Operation • Your Internet connection should be configured to keep the Internet connection active as much as possible (Keep Alive). • Once logged in to the SIP server, you can dial any number using the procedure specified by your VoIP Service provider.
Appendix A Troubleshooting A This Appendix covers the most likely problems and their solutions. Overview This section covers some common problems that may be encountered while using the IAD-200 / IAD-200W and some possible solutions to them. If you follow the suggested steps and the IAD-200 / IAD-200W still does not function properly, contact your dealer for further advice. General Problems Problem 1: Can't connect to the IAD-200 / IAD-200W to configure it.
Problem 2: Some applications do not run properly when using the IAD-200 / IAD200W. Solution 2: The IAD-200 / IAD-200W processes the data passing through it, so it is not transparent. For incoming connections, you must use the Virtual Server or Firewall Rules to specify the PC which will receive the incoming traffic. You can also use the DMZ function. This should work with almost every application, but: • It is a security risk, since the firewall is disabled. • Only one (1) PC can use this feature.
stations. This will mean high access speed is only possible when close to the IAD-200W.
Appendix B About Wireless LANs (IAD-200W only) B This Appendix provides some background information about using Wireless LANs (IAD-200W only). Modes Wireless LANs can work in either of two (2) modes: • Ad-hoc • Infrastructure Ad-hoc Mode Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wireless Stations (e.g. notebook PCs with wireless cards) communicate directly with each other.
Channels The Wireless Channel sets the radio frequency used for communication. • Access Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least interference and best performance. In the USA and Canada, 11 channels are available. If using multiple Access Points, it is better if adjacent Access Points use different Channels to reduce interference.
Wireless LAN Configuration To allow Wireless Stations to use the Access Point, the Wireless Stations and the Access Point must use the same settings, as follows: Mode On client Wireless Stations, the mode must be set to "Infrastructure". (The Access Point is always in "Infrastructure" mode.) SSID (ESSID) Wireless Stations should use the same SSID (ESSID) as the Access Point they wish to connect to. Alternatively, the SSID can be set to "any" or null (blank) to allow connection to any Access Point.
105