802.
Table of Contents Package Contents............................................................................ 3 Physical Details................................................................................ 4 Front Panel LEDs........................................................................ 4 Rear Panel................................................................................. 5 Rear panel Port and Button Definition.......................................... 5 Installation Procedure...........
Package Contents The following items should be included: l ADN-4000 Unit x 1 l Quick Installation Guide x 1 l User’s Manual CD x 1 l Power Adapter x 1 l RJ-45 Cable x 1 l RJ-11 Cable x 2 l Antenna x 3 l ADSL Splitter x 1 If any of the above items are damaged or missing, please contact your dealer immediately.
Physical Details Front Panel LEDs LED PWR WLAN WPS ADSL LAN1-4 Status Description ON The Router is ready.
Rear Panel Rear panel Port and Button Definition Port Description Reset ● Reboot router: press the reset button for less than 5 seconds, and it will keep your original configurations. ● Load factory default setting: press the reset button for longer than 5 seconds and the router will reset itself to the factory default settings (Warning! your original configurations will be replaced with the factory default settings) Power Power connector with 12V DC 1A.
Installation Procedure 1. Choose an Installation Site Select a suitable place on the network to install the ADN-4000. Note For best Wireless reception and performance, the ADN4000 should be positioned in a central location with minimum obstructions between the ADN-4000 and the PCs. Also, if using multiple Access Points, adjacent Access Points should use different Channels. 2. Connect LAN Cables Use standard LAN cables to connect PCs to the Switching Hub ports on the ADN-4000.
3. Connect ADSL Cable Connect the supplied ADSL cable from to the WAN port on the ADN4000 (the RJ-11 connector) to the ADSL terminator provided by your phone company. 4. Power Up Connect the supplied power adapter to the ADN-4000. Use only the power adapter provided. Using a different one may cause hardware damage. 5. Check the LEDs • The PWR LED should be ON. • The WLAN LED should be flash, when wireless AP is ready. • The ADSL LED should be ON if ADSL line is connected.
Configuration The ADN-4000 contains a HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Preparation Before attempting to configure the ADN-4000, please ensure that: • Your PC can establish a physical connection to the ADN-4000. The PC and the ADN-4000 must be directly connected (using the Hub ports on the ADN-4000) or on the same LAN segment. • The ADN-4000 must be installed and powered ON. • If the ADN-4000's default IP Address (192.168.1.
2. A user name and password prompt will appear. The user name and password are both “admin”. Setup Wizard You can use “Setup Wizard” to setup the router as follows, and the router will connect to the Internet via ADSL line. Click “Quick Start” to get into the quick setup procedures. Click “RUN WIZARD” to start up this procedure.
Step 1 - Click “Next” to begin these four quick steps. Step 2 - Click “Next” to setup your new administrator’s password.
Step 3 - Click “Next” to setup your time zone. Step 4 - Click “Next” to setup your Internet connection type. You can have this information from your Internet Service Provider.
Step 5 - Enter the connection information provided by your ISP. Step 6 - The Setup Wizard has completed. If you have any change or mistake, click “Back” to modify it, or click “Next” to save the current settings.
Step 7 - Saved Changes. Home Screen After finishing the Setup Wizard, you will see the Home screen. When you connect in future, you will see this screen when you connect. An example screen is shown below.
Further information If you still have problem on connecting to your ISP, please check the user’s manual on the bundled CD for detail configuration. If you have any other questions, please contact the dealer where you purchased this product or you can contact PLANET directly at the following email address: support@planet.com.
This page is intentionally left blank
This page is intentionally left blank
