01 PLANET ECLIPSE: EMEK USER MANUAL / ENGLISH EMEK
002 2 WARNINGS READ CAREFULLY BEFORE USE ! THE PLANET ECLIPSE EMEK IS NOT A TOY. PAINTBALL SAFETY RULES MUST BE FOLLOWED AT ALL TIMES. ! areless or improper use of the EMEK, including failure to follow C instructions and warnings within this User Manual could cause serious injury or death. ! Do not remove or deface any warnings attached to the EMEK.
03 0 3 WARNINGS READ CAREFULLY BEFORE USE ! Persons under 18 years of age must have adult supervision when using or handling the EMEK. ! Use only professional paintball fields where codes of safety are strictly enforced. ! se compressed air/nitrogen only. Do not use any other U compressed gas or pressurised liquid including CO2. ! lways follow instructions, warnings and guidelines given with any A first stage regulator you use with the EMEK.
04 CONTENTS GAME ON! QUICK START (06-14) TECHNICAL (18-26) 06 08 10 11 12 14 18 20 21 22 23 24 25 26 Setting up the EMEK The EMEK safety switch Velocity adjustment Detents Unloading the EMEK Storage and transportation MAINTENANCE (15-17) 15 16 On-line maintenance videos Fault-finding tables EMEK Parts list EMEK inline regulator Three-way assembly Bolt assembly (68cal) Bolt assembly (50cal) Frame assembly Clamping feed neck assembly Two-piece grips SUPPORT (27-31) 27 28 Our promise Notes
05 T O G E W UR YO CK!!! BA EMEK FOLLOW OUR OFFICIAL PLANET ECLIPSE SOCIAL MEDIA CHANNELS TO KEEP UP TO DATE WITH OUR TECH SUPPORT EVENTS CALENDAR. O SE PR P I L L C TS AL NET E N A E L V P E F LL AT RMY O NTBA RE TH U S E OUR A TTEND PAI AK R ARE TO M SA E D K L R R A TECH S, O PSE M T ALL TIME HE W I T L R C E E OV UR S, A ND YO CYLINDER A U YO LL S.
QUICK START 06 SETTING UP THE EMEK FIG-1 F 5 G 5/32 E H C B A 2 1 4 D 3 EMEK
07 QUICK START SETTING UP THE EMEK FIG-1 A Turn the safety switch to SAFE (S) before you begin. B Fit the Emek barrel. Rotate the barrel clockwise into the marker body. C Attach a barrel blocking device for safety. D Attach the preset air system. Rotate the air system clockwise into the ASA body. E Loosen the clamping feed neck. Open the feed neck lever away from the feed neck. Rotate the feed neck lever screw counter-clockwise. F Attach the loader.
08 QUICK START THE EMEK SAFETY SWITCH - SAFE (S) FIG-1 FIG-1 The safety switch A is located on the left side of the Emek frame and is used to switch between SAFE (S) and FIRE (F). A Enabling SAFE (S): Rotate the safety switch A counter-clockwise until the S indicator B is revealed and the switch arrow points towards S. The trigger is now locked. B FIG-2 SAFE (S) is also represented on the right side of the frame by the switch arrow C pointing towards the S indicator D .
09 QUICK START THE EMEK SAFETY SWITCH - FIRE (F) FIG-1 FIG-1 The safety switch A is located on the left side of the Emek frame and is used to switch between SAFE (S) and FIRE (F). B Enabling FIRE (F): Rotate the safety switch A clockwise until the F indicator B is revealed and the switch arrow points towards F. The trigger is now unlocked.
QUICK START 10 VELOCITY ADJUSTMENT FIG-1 FIG-1 Insert a 1/8 hex key A into the velocity adjuster screw B to alter the velocity of the EMEK. Adjusting the velocity: 1 Turn the hex key clockwise to reduce velocity. 2 Turn the hex key counter-clockwise to increase velocity. 3 Fire two clearing shots after each velocity adjustment for an accurate velocity reading. 1 - 1 DO NOT turn the adjuster screw in too far. This will prevent the EMEK from firing. + B 1/8 WARNING! DO NOT exceed 300FPS.
QUICK START DETENTS The Emek rubber detents (see Fig-2) hold each paintball in place until ready to fire. This prevents paintballs from rolling down the barrel and maintains feed consistency. FIG-1 5/64 These can be removed for cleaning or replacement. B A FIG-1 Use a 5/64” (2mm) hex key A to remove the breech cover screw B by rotating counter-clockwise. This will release the breech cover (see Fig-2).
QUICK START UNLOADING THE EMEK FIG-1 4 E 5/32 D 2 B F A 1 3 C EMEK
QUICK START UNLOADING THE EMEK FIG-1 A Turn the safety switch to SAFE (S) before you begin. B Attach a barrel blocking device for safety. C Remove the preset air system. Rotate the air system counter-clockwise from the ASA body. D Loosen the clamping feed neck. Open the feed neck lever away from the feed neck. Rotate the feed neck lever screw counter-clockwise. E Remove the loader. If the feed neck is too tight, loosen the clamping feed neck more. F Remove the Emek barrel.
QUICK START STORAGE AND TRANSPORTATION 1 Your EMEK must be clear of all paint and propellant during transportation or storage. 2 Make sure the safety switch is turned to SAFE (S). 3 Remove the barrel from the marker. 4 Make sure the marker is clean of any paint residue, dirt and moisture. 5 Store your EMEK in a clean, cool, dry place. 6 Keep your EMEK away from any unauthorized or unsafe users. WARNING! 7 Protect your EMEK from excessive heat during transportation.
MAINTENANCE ONLINE MAINTENANCE VIDEOS To help demonstrate how to maintain and service essential parts of the EMEK we’ve created a collection of dedicated marker maintenance videos to guide the user through each step. From basic, to more advanced parts of the EMEK, we’ve got your back. Visit our Tech Room YouTube channel and check out the EMEK Maintenance playlist. www.youtube.
MAINTENANCE FAULT FINDING TABLES SYMPTOM POSSIBLE CAUSE The gasket between the three-way body and gun body, o-ring on air transfer pipe or the gasket under the three-way plate are damaged or dirty. Ensure the gasket is seated correctly. Replace the gaskets if damaged using EMEK parts kit. Check condition of the air transfer pipe 010 NBR70 o-ring. Three-way is over-pressurised. Check the output pressure of the inline regulator and adjust accordingly.
MAINTENANCE FAULT FINDING TABLES SYMPTOM POSSIBLE CAUSE SOLUTION The air system is not fully engaged. Screw in the air system until it fully engages. The three-way is damaged. Replace the three-way. Low constant velocity. The inline regulator output pressure set too low. Increase the output pressure of the inline regulator. High velocity first shot. The inline regulator pressure is creeping.
TECHNICAL PARTS LIST FIG-1 1 2 16 4 5 3 6 8 9 7 11 10 12 14 13 15 EMEK
TECHNICAL PARTS LIST FIG-1 1 Clamping feed tube assembly 9 Front frame screw 2 Marker body shell 10 Frame assembly 3 Back cap 11 Trigger assembly 4 Bolt assembly 12 Grip retaining clip 5 Rubber detent 13 Regulator assembly 6 Safety switch 14 Foregrip 7 Three-way assembly 15 ASA assembly 8 Rear frame screw 16 Barrel o-ring #016 NBR70 EMEK
TECHNICAL EMEK INLINE REGULATOR 1 FIG-1 Regulator spring 2 Inlet pipe Regulator seal Regular body Regulator body o-rings #015 NBR70 Adjuster top Adjuster o-ring #011 NBR70 Regulator piston Adjuster external o-ring #011 NBR70 Purge poppet 3 Purge poppet spring Adjuster bottom EMEK #010 NBR70 Piston o-ring 14 x 2 NBR70 #010 NBR70 Regulator cap Adjuster internal o-ring #008 NBR70 1 Reset the EMEK regulator to factory after re-assembly.
TECHNICAL THREE-WAY ASSEMBLY FIG-1 Three-way valve gasket Three-way valve cap Emek transfer block Three-way valve spool Three-way valve gasket 4 x 1 NBR70 Three-way valve body #6 Seal (custom) #6 Seal (custom) EMEK
TECHNICAL BOLT ASSEMBLY (68CAL) FIG-1 #014 NBR70 14 x 2 NBR70 10-32 UNF x 0.
TECHNICAL BOLT ASSEMBLY (50CAL) FIG-1 Can #011 NBR70 10-32 UNF x 0.
TECHNICAL 24 FRAME ASSEMBLY FIG-1 FIG-1 1 Foregrip 2 Safety switch 3 Foregrip cap 4 Frame assembly 5 Three-way body pins and 3x1 NBR70 o-ring 6 Front frame screw 7 Rear frame screw 8 ASA retaining nuts 9 ASA screws 10-32 UNF x 1” cap head socket 10 Trigger assembly 11 Trigger spring 12 Trigger plate 13 Trigger plate retaining screws 14 Three-way assembly 15 Three-way push pin 16 Trigger pin EMEK 13 12 11 14 10 15 16 4 2 5 1 7 6 5 8 3 8 9
TECHNICAL CLAMPING FEED NECK ASSEMBLY FIG-1 FIG-1 The EMEK clamping feed neck uses our patented Deftek system, meaning the feedneck is designed to be slightly offset to neutralise any paintball bounce-back, providing the optimum paintball feed system.
TECHNICAL 26 TWO-PIECE GRIPS FIG-1 A The EMEK’s tool-less two-piece grip system makes it incredibly easy to remove and clean the grips after a big day out in the field. FIG-1 A Locate and pull back the rear grip locking tab. B Use the finger recess to help release the rear grip section. C Once released, fully remove the rear grip section from the frame. D The front grip section can now be released and removed.
SUPPORT OUR PROMISE SUPPORT QUALITY As an Eclipse customer you will have access to our worldwide technical support network that will help you with any technical problems from localised service centres to on-site* tech support. All Eclipse products undergo meticulous checks by experienced specialists who care about the product that arrives at your door. Stringent quality control and the use of precision materials equals a quality product.
SUPPORT 28 INDEX A G B I Air system: 07,13,17 ASA: 07,13,19,24 Back cap: 19,22,23 Barrel: 02,07,10,13,14,16,17 Bolt assembly: 04,19 Breech cover: 11 C Clamping feed neck: 07,13,25 D Detent: 11,17,19 F Feed tube: 02,19 F indicator: 09 Fire: 07,08,09,13 Foregrip: 19,24 Frame screw: 19,24 EMEK Grip retaining clip: 19 Grips: 04,26 Inline regulator: 04,16,17,20 L Loader: 07,13,16,17 M Maintenance: 02,04,15 O O-ring: 16,19,20,24,25 P Preset air system: 07,13 R Register: 30 Regulator ass
YOUR WARRANTYREGISTRATION CARD. Planet Eclipse offers a 12 month limited warranty period* on the Eclipse® electro-pneumatic marker. The Eclipse® electro-pneumatic marker is warranted to be free from all manufacturing and production defects for a period of 12 months from the time of original purchase**. Warranty cover is dependent on successful completion, and receipt by Planet Eclipse Limited, of warranty registration and proof of purchase, either in electronic form on www.planeteclipse.
GETMORE - PLANETECLIPSE.COM PLANET ECLIPSE 130 FRANKLIN STREET BUILDING L4 & L5 WARREN RHODE ISLAND 02885 U.S.A. TO BENEFIT FROM OUR INDUSTRY-LEADING GLOBAL TECH SUPPORT PLEASE REGISTER YOUR MARKER ONLINE TODAY EMEK WARRANTY.PLANETECLIPSE.COM LICK. STICK. SEND.
SUPPORT NOTES EMEK
GET MORE PLANETECLIPSE.COM THIS PRODUCT IS COVERED BY AND/OR LICENSED UNDER ONE OR MORE OF THE FOLLOWING PATENTS: G.B. PATENTS: 2,342,710; 2,345,953; 2,352,022; 2,391,292; 2,391,063; U.S.
