When image experience matters. Planar System,Inc. 1195 NW Compton Drive Beaverton,OR 97006 USA www.planar.com Technical Support:1-866-752-6271 www.planar.com/support PS5580 • 2013.08.
Features of PS5580 ▶ Enjoy a wide flat screen with high brightness and high quality. ▶Easy to install and move due to its thin design ▶ Enjoy your favorite programs with various split-screen features simultaneously presenting several programs. Thank you for purchasing our PS5580 monitor. This manual describes how to use the product and notes in use. Please read the manual carefully before using it. After reading this manual, please retain for future reference.
Contents ※European Union Disposal Information.................................................................................................................... 4 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ※Cautions for consisting PS5580 System .............................................................................................................. 5 ※Clearance for Ventilation ............................................................................................................................
English WARNING Disposal of old Electrical & Electronic Equipment (Applicable throughout the European Union and other European countries with separate collection programs) This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment.
WARNING - When you install PS5580 make sure there is at least 20cm clearance for effective ventilation and do not seal off PS5580 sets. If PS5580 sets are installed at the locations of bad ventilation, the inner temperature can be raised rapidly and it can cause frequent malfunctions and rapid reduction of the product life. ※Cleaning and Maintenance - Regularly clean off the vent holes in the back of PS5580 sets.
※Handle with Caution. Warning - This product can be damaged even with minor impact for its nature. Please keep following instruction to carry or store the products. PANEL PANEL -Shock/Impact on the set's sides will result in internal circuit damages. -The edge/bottom of the panel are fragile. Use shock-absorbing pads or rugs for laying down the product. PANEL PANEL CUSHION PANEL • If you need to stand LCD, you must lean over the LCD to avoid panel touches ground or floor .
※Application information WARNING If static images are displayed on the screen for a long time, it causes burn-in image. Please keep the following instruction to optimize the lifetime and functions of the product. It always needs two persons to carry or install PS5580 . When you carry PS5580 with up straight manner, please hold handles on the back and bottom part of the panel together. Please be careful not to touch the bottom part of the panel when you put down the panel. 1.
WARNING WARNING Warning ※Attention for Installing Fixed • Avoid giving a shock or damage at LCM corner or other parts during setting Multi-Vision. • Keep all LCMs balanced in vertical or horizontal force after setting • Multi-Vision. Avoid LCM is set up tilted so it can give a damage to down LCM. - 12 - • Avoid that LCM is twisted. • Avoid that LCM outside is shocked or damaged by sharp thing.
1. Safety Precautions • If it operates abnormally, stop using it immediately. • Do not place any liquid-containing container on it. If the inside is wet, it may cause electric shock or fire. • Do not put any foreign material into the product. It may cause a failure or shorten the life span. • Do not pull out or hang down the connection cable. It may damage the cord to cause fire or electric shock. • Do not lean against the product or keep it leaned. It may cause injury or failure.
2. Names ▶ Front ▶ Input Ports LAN SRC MODE ▶ Rear ENT IR RS232C IN RS232C OUT DP IN HDMI 1-IN HDMI 2-IN DVI IN DVI OUT PC IN AC IN IR LAN IR RS232C IN RS232C OUT DP IN ➊ ➋ ➌ ➍ ➎ HDMI 1-IN ➏ HDMI 2-IN DVI IN DVI OUT PC IN AC IN ➐ ➑ ➒ ➓ 1. LAN Display control via Ethernet (RJ45) 8. DVI IN 2. IR Digital RGB Signal, DVI Single Link 24Pin Remote controller input port 3. RS-232C IN 9.
▶ KEY PAD ▶ Remote Controller POWER ON : Turn on the display POWER POWER OFF : Turn off the display OFF PICT. MUTE A.SETUP ZOOM SP.SEL A.ADJ 1 2 3 4 5 6 7 8 9 GUIDE 0 INFO Number Button : Used to enter the LAN Network infomation and security password LAN SRC MODE ENT IR RS232C IN RS232C OUT DP IN HDMI 1-IN HDMI 2-IN DVI IN DVI OUT PC IN AC IN A.ADJ : Automatically adjusts Screen Size, Hposition, V position, Clock, Clock Phase (RGB Only) IR MENU OK ▲ RS D.
3. How to Connect Cables • Do not connect/disconnect cables while PS5580 or other external equipments are turned on. • First turn off the power all the attached equipment and make connections. IR Reception • Make sure the power cord is inserted properly into the power inlet to prevent unexpected pullout of the cord. 3.1. Connection of Single PS5580 • PS5580 and PC should be connected; a Com Port in a PC and RS-232C IN port in a PS5580 is connected with supplied RS-232C cable.
3.2. Connection of Multiple PS5580 (for DP in) 3.3. Connection of Multiple PS5580(for HDMI in) • Image quality can be affected by cable or signal quality. • It is recommended you purchase an HDMI-certified cable. Otherwise, the screen may appear blank or a connection error may occur. • Please use DisplayPort cable with DisplayPort certified logo. • Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
3.4. Connection of Multiple PS5580(for DVI in) 3.5. Connection of Multiple PS5580(for PC in) • Recommended maximum set connection for Multi setting is shown in table below. If you need to connect more than described in the table, you have to use distributors. • Image quality can be affected by cable or signal quality. • Image quality can be affected by cable or signal quality.
3.6. Connection of Control Cable • Control signal transmission can be connected by 3 different methods.(RS-232C or Ethernet or IR) • RS-232C and Ethernet connection cannot be used simultaneously. • All control signals are output to the RS-232OUT after conversion to RS-232C signal. 3.6.2. Connection of Ethernet Cable 3.6.1. Connection of RS-232C Cable & IR Receiver • Maximum use of RS-232C with Daisy Chain connection is 30 sets or less, if you need additional connection, use RS-232C distributor.
4. How to use Remote Controller 5. Configuration 1. MENU button OSD MENU will be displayed by pressing MENU button. Moves from sub menu to the main menu. POWER PICTURE Mode OFF BRIGHTNESS, CONTRAST, TINT, COROR, VIDEO MODE, and PICTURE RESET can be adjusted in the PICTURE MENU. POWER PICT. MUTE ZOOM SP.SEL A.SETUP PICTURE u A.
▶ BRIGHTNESS ▶ CONTRAST Adjust the overall image and background brightness. Adjust the image brightness in relationship to the background. 1. Select BRIGHTNESS from PICTURE Menu. 1. Select CONTRAST from PICTURE menu. Select BRIGHTNESS and move ▼▲ buttons to adjust the value. PICTURE u SCREEN AUDIO PIP SETUP A BRIGHTNESS 50 BACK LIGHT 90 CONTRAST 50 SHARPNESS 50 TINT 0 COLOR 50 Select CONTRAST and move ▼▲ buttons to adjust the value.
▶ TINT ▶ COLOR TEMPERATURE Adjust Red and Green color of the screen. Adjust the color temperature of the screen. 1. Select TINT from PICTURE Menu. 1. Select GAMMA SELECTION from PICTURE Menu. Select TINT and move ▼▲buttons to adjust the value. PICTURE u SCREEN AUDIO PIP SETUP A BRIGHTNESS 50 BACK LIGHT 90 CONTRAST 50 SHARPNESS 50 TINT 0 COLOR 50 Select COLOR TEMPERATURE. PICTURE u SCREEN AUDIO PIP SETUP A COLOR TEMPERATURE SETUP B OPTION COLOR BALANCE p q 2.
▶ COLOR BALANCE ▶ GAMMA SELECTION If Color TEMPERATURE needs further adjustment, the individual R/G/B levels of the white point can be adjusted. 1. Select COLOR BALANCE from PICTURE Menu. Select a display gamma for best picture quality. 1. Select GAMMA SELECTION from PICTURE Menu. Select GAMMA SELECTION and move ▼▲buttons to adjust the value. Select COLOR BALANCE and move ▼▲buttons to adjust the value.
▶ PICTURE RESET ▶ COLOR SPACE Initialize the values of PICTURE NENU. Select a color space for best picture quality. 1. Select PICTURE RESET from PICTURE menu. 1. Select COLOR SPACE from PICTURE Menu. Press MENU button to display OSD. Press ▼ or ▲ buttons to move to PICTURE RESET and press OK button. Select COLOR SPACE and move ▼▲buttons to adjust the value.
SCREEN Mode (For PC In ) ▶ H POSITION H POSITION, V POSITION, CLOCK, CLOCK PHASE and SCREEN RESET can be adjusted in the SCREEN MENU. 1. Press MENU button. Press MENU button to display OSD MENU on the screen. PICT. MUTE 1. Select H POSITION from SCREEN menu. Adjust H POSITION values with ▼▲ buttons after selecting H POSITION. POWER OFF Adjust the horizontal position of the display image on the screen. PICTURE A.SETUP SCREEN ZOOM SP.SEL A.
▶ CLOCK ▶ SCREEN RESET Adjust the width of the display image on the screen. Initialize the values of SCREEN MENU. 1. Select CLOCK from SCREEN menu. 1. Select SCREEN RESET from SCREEN menu. Adjust CLOCK values with ▼▲ buttons after selecting CLOCK. PICTURE SCREEN u H POSITION 50 V POSITION 50 64 CLOCK AUDIO PIP CLOCK PHASE 62 SCREEN RESET p q NO Press MENU button to display OSD. Press ▼ or ▲ buttons to move to SCREEN RESET and press OK button.
SETUP A Menu ▶ AUTO ADJUST (For PC IN) AUTO SETUP, AUTO ADJUST, POWER SAVE, AUTO POWER, LANGUAGE, SETUP A RESET and KEY LOCK can be adjusted in SETUP A MENU. 1. Press MENU button. PICT. MUTE ZOOM SP.SEL 1 2 4 A.ADJ PICTURE PICTURE 9 0 INFO u p q OFF p q OFF AUTO POWER PIP p q OFF LANGUAGE ENGLISH p q SETUP A RESET NO p q KEY LOCK NORMAL p q EXIT ▲ ▲ Move Enter ▲ ▲ .R SD 23 2 O LAN u Press ▼ or ▲ buttons to move to SETUP A MENU.
▶ POWER SAVE ▶ AUTO POWER The monitor will automatically turn off after 10minutes when there is no signal. The monitor will be turned on automatically when power is connected. 1. Select POWER SAVE from SETUP A menu . 1. Select AUTO POWER from SETUP A menu. Press MENU button to display OSD. Press ▼ or ▲ buttons to move to POWER SAVE and press OK button..
▶ LANGUAGE ▶ SETUP A RESET Select the language used for the OSD. Initialize the values of SETUP A MENU. 1. Select LANGUAGE from SETUP A menu. 1. Select SETUP A RESET from SETUP A menu . Press MENU button to display OSD. Press ▼ or ▲ buttons to move to LANGUAGE and press OK button..
SETUP B ▶ KEY LOCK Restrict key strokes to prevent any of expected set activities. To return to normal operation, press the “ENT” button on the KEY PAD for 3 sec. LOCK – Key buttons will not work. NORMAL – Key buttons will work. SERIAL CONTROL, LAN SETTING, OSD, OFF TIMER, SETUP B RESET and FACTORY RESET can be adjusted in SETUP B MENU. 1. Select KEY LOCK from SETUP A menu. PICT. MUTE A.SETUP ZOOM SP.SEL A.
▶ SERIAL CONTROL ▶ LAN SETTING Select the LAN On or LAN Off. Configure the IP address of the set to control via Ethernet. 1. Select SERIAL CONTROL from SETUP B menu. 1. Select LAN SETTING from SETUP B menu. Press MENU button to display OSD. Press ▼ or ▲ buttons to move to SERIAL CONTROL and press OK button. PICTURE SERIAL CONTROL SCREEN AUDIO PIP SETUP A SETUP B p q RS232C LAN SETTING PICTURE SCREEN OSD 120 SEC.
▶ OSD » TURN OFF It configures OSD menu. Turns off the OSD after a period of inactivity. The preset choices are 5-120 seconds. 1. Select OSD from SETUP B menu. Press MENU button to display OSD. Press ▼ or ▲ buttons to move to OSD and press OK button. PICTURE SCREEN AUDIO PIP SETUP A SETUP B SERIAL CONTROL RS232C p q LAN SETTING DHCP p q OSD 120 SEC.
» POSITION » ROTATION Select the location where the OSD appears on the screen. Select the OSD display direction between landscape and portrait. 1. Select OSD H POSITIION 1. Select ROTATION from OSD menu. Press ▼ or ▲ buttons to adjust OSD H POSITION value.
» INFO DISPLAY » TRANSPARENCY Select to display or not display the infomation OSD. The information OSD will be displayed when the input signal or source are changed. The information OSD will also give a warning when there is no-signal or the signal is out-of range. An display interval for the information OSD can be selected between 3 to 10 seconds. Setup the transparency level of the OSD. 1. Select TRANSPARENCY from OSD menu. Press ▼ or ▲ buttons to move to transparency and press OK button. 1.
▶ OFF TIMER ▶ SETUP B RESET Setup the monitor to power off after a certain of time. Time period can be selected from 1 to 24 hours. Initialize the previously adjusted values of SCREEN B MENU. 1. Select SETUP B RESET from SETUP B menu. 1. Select OFF TIMER from SETUP B menu. Press ▼ or ▲ buttons to move to OFF TIMER and press OK button. PICTURE SCREEN AUDIO PIP SETUP A SETUP B SERIAL CONTROL LAN p q LAN SETTING DHCP p q OSD 120 SEC.
OPTION ▶ FACTORY RESET Initialize the previously adjusted values of the set to the factory level. Every configuration will be initialized. 1. Select FACTORY RESET from SETUP B menu. POWER Press MENU button to display OSD. Press ▼ or ▲ buttons to move to FACTORY RESET and press MENU button. PICTURE SCREEN AUDIO p q LAN SETTING DHCP p q OSD 120 SEC. p q OFF p q OFF TIMER FACTORY RESET SETUP A Press MENU button to display OSD MENU on the screen. PICT. MUTE A.SETUP ZOOM SP.
▶ INPUT RESOLUTION ▶ CHANGE SECURITY PASSWORD Chang the the security password. The factory preset password is 9999. This password is applied to the TILING MENU LOCK menu. Display the current input resolution. PICTURE SCREEN INPUT RESOLUTION 1920 x 1080@50Hz p q SCAN MODE NORMAL p q CHANGE SECURITY PASSWORD AUDIO PIP SETUP A TILING MENU LOCK OFF p q GROUP ID A p q IR CONTROL NORMAL p q DISABLE p q 2 SEC.
▶ TILING MENU LOCK ▶ GROUP ID Lock the tiling menu to protect the tiling display setting. Setup the Tiling Group. 1. Select TILING MENU LOCK from OPTION menu. 1. Select GROUP ID from OPTION menu. Press ▼ or ▲ buttons to move to TILING MENU LOCK menu and press OK button. PICTURE SCREEN INPUT RESOLUTION 1920 x 1080@50Hz p q SCAN MODE NORMAL p q CHANGE SECURITY PASSWORD AUDIO PIP SETUP A OPTION ---- GROUP ID A p q IR CONTROL NORMAL p q DISABLE p q 2 SEC.
▶ IR CONTROL ▶ TILING Prevents the monitor from being controlled by the remote controller. To return to normal operation, press the “ENT” button on the KEY PAD for 3 sec. 1. Select IR CONTROL from OPTION menu. Allows one image to be expanded and displayed over multiple screens. . 1. Select TILING from OPTION menu. Press ▼ or ▲ buttons to move to TILING menu and press OK button. Press ▼ or ▲ buttons to move to IR CONTROL menu and press OK button.
▶ POWER ON DELAY ▶ POWER ON INPUT DETECT Adjust the delay time between being in “standby” mode and entering “power on” mode.. Select the default input source for power on. 1. Select POWER ON DELAY from OPTION menu. 1. Select POWER ON INPUT DETECT from OPTION menu. Press ▼ or ▲ buttons to move to POWER ON DELAY menu and press OK button. PICTURE SCREEN INPUT RESOLUTION 1920 x 1080@50Hz p q SCAN MODE NORMAL p q CHANGE SECURITY PASSWORD AUDIO A p q NORMAL p q DISABLE p q 2 SEC.
6. Before calling for service 7. Applicable signals • Before calling for any repair, check the following and then refer to a near A/S center. ▶"Tick" sound from the main body. -- I f there is no problem with the screen or sound, the "tick" sound is likely to result from the cabinet lightly shrinking with the change of room temperature. The sound does not affect product’s performance. ▶No image at upper and lower part of the screen.
8. Specification 9. Regulatory Information PS5580 Model Name Back Light Unit Type LED 1209.6 X 680.4mm Active Display Area (H X V) Number of pixels 1920 (H) X 1080 (V) Pixel Pitch 0.630 X 0.630 mm 1.07Billion Display Colors 400 cd / m2 Luminance of White 4,000 : 1 Contrast ratio (Dark Room) Bezel 7 / 6 / 6 / 6 (U/D/L/R) mm Power Supply AC100V ~ 240V (50/60Hz) Max 125W Typical 120W Stand-By ＜1.
10. Dimension Memo 1224.2(±1.5) 7.3 6.3 6.3 696.0(±1.5) 6.3 50 30 400 61.3 400 LAN PWR SRC MODE ENT IR RS232C IN RS232C OUT DP IN HDMI 1-IN HDMI 2-IN DVI IN DVI OUT PC IN AC IN 124.5 IR 61.3 61.
