PD4010 PD7010 PD7060 User's Guide
English Planar Systems, Inc. Corporate Headquarters 1195 NW Compton Drive Beaverton, OR 97006-1992 Planar Customer Support Telephone: US: 1-866-PLANAR1 (866) 752-6271 Outside US: (503) 748-5799 E-mail: PlanarSupport@planar.com Online Technical Library: http://www.planar.com/support Hours: M-F, 8am - 8pm ET, 12pm - 12am GMT Français Planar Systems, Inc.
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright October, 2006 About this User’s Guide This User’s Guide is intended for end users and describes how to quickly install and operate the DLP projector.
PACKING CHECKLIST Carefully unpack the projector and check that the following items are included. DLP Projector DVI to HDMI Adaptor (PD4010 only) Remote Control (with two AAA batteries) Power Cord (By country) Component Video Cable PD4010 PD7010 PD7060 User's Guide CD-ROM (This User’s Manual) User’s Guide Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
REMOTE CONTROL FUNCTIONS ITEM LABEL 1 Power On Turns projector power on 2 3 4 Power Off Source 1 Source 2 5 6 7 8 9 10 11 13 Source 3 Source 4 Source 5 Up cursor Left cursor Enter Right cursor Down cursor Exit Turns projector power off User configurable (Default: HDMI) User configurable (Default: Component) User configurable (Default: DVI-D) User configurable (Default: PC) User configurable (Default: Video) 14 15 16 17 Menu Hot Key 1 Hot Key 2 Hot Key 3 18 19 20 21 Contrast Brightness Aspect r
INSERTING THE REMOTE CONTROL BATTERIES 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Insert the supplied batteries taking note of the polarity (+/-) as shown here. 3. Replace the cover. CAUTION 6 1. Only use AAA alkaline batteries. 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolonged periods.
CONNECTING INPUT DEVICES A PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders, digital still cameras and high definition sources. Check the User’s Manual of the connecting device to confirm it has the appropriate output connector. As a safety precaution, disconnect all power to the projector and connecting devices before making connections.
STARTING AND SHUTTING DOWN THE PROJECTOR 1. Remove the lens cover. 2. Connect the power cord to the projector. Connect the other end to a wall outlet. 3. Press the Power button. The Power LED on the projector turns on. Turn on the connected devices. The language selection screen appears (Initial setup only). Select the desired language. 4. 1. Press the cursor STbutton until Language is highlighted. 2. Press the cursor W X or Menu button to confirm the language, and close the OSD. 5.
ADJUSTING THE FOCUS AND ZOOM 1. Locate the image zoom and focus adjustment rings on the projector. 2. Use the image zoom control to resize the projected image and screen size. 3. Zoom Focus Rotate the image focus control to sharpen the projected image.
TROUBLESHOOTING These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions. • • • • • • Use some other electrical device to confirm that the electrical outlet is working. Ensure the projector is turned on.
Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3.
REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Planar Systems, Inc. Corporate Headquarters 1195 NW Compton Drive Beaverton, OR 97006-1992 Planar Customer Support Telephone: US: 1-866-PLANAR1 (866) 752-6271 Outside US: (503) 748-5799 E-mail: PlanarSupport@planar.com Online Technical Library: http://www.planar.com/support Hours: M-F, 8am - 8pm ET, 12pm - 12am GMT ©2006 Planar Systems, Inc. Planar is a registered trademark of Planar System, Inc. Other brands and names are the property of their respective owners.
