LA1950RTR / LA1950RTC LA1950RTS / LA1950R Touch Screen LCD Monitor USER’S GUIDE www.planartouch.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. Nopart of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc.
Table of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About LA1950 Series.............................................................................................................. 2 Touch Screen for LA1950RTR................................................................................................ 2 Touch Screen for LA1950RTC.............................................
Usage Notice ! ! Warning - To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: • Turn off the product before cleaning.
Introduction About LA1950 Series The LA1950 Series is a 19" flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: • Direct Analog signal input • Active matrix TFT LCD technology • 1280x1024 SXGA resolution • 19” viewable display area • 31.47 ~ 80 kHz horizontal scan • 56 ~ 75 Hz high refresh rate • 0.294mm x 0.
Touch Screen for LA1950RTS • Surface Acoustic Wave (SAW) touch screen for finger and stylus input • Surface: Anti-glare treatment • Interface: Dual RS-232 Serial/USB controller • Transmittance: 92±5% • Driver: Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple® Mac OS Non-Touch Screen for LA1950R • Pure Glass • Surface: Anti-glare treatment • Interface: N/A • Transmittance: 91.
Package Overview LCD Display DC Power Supply Quick Start Guide Power Cord VGA Signal Cable RS-232 Cable USB Cable ( A to B ) (LA1950RTR/RTC/RTS only) (LA1950RTR/RTC/RTS only) Bracket Screw 4
Product Overview • Front View • LA1950RTR / LA1950RTC / LA1950RTS Bottom View VGA RJ-11 USB DC IN RS-232 • LA1950R Bottom View VGA RJ-11 DC IN 5
Attaching the L-Brackets Depending on your mounting scheme, alternately, you may use the L-brackets to mount your displays onto your wall or device. Find a suitable location for attaching L-brackets. A. The left and right sides B. The Top and bottom sides Bracket Bracket or Bracket Bracket Note: You will need a screwdriver to attach the L-brackets. Your kiosk touch monitor included two L-brackets (and four screws, M4x6).
Side Mount For Your Monitor This monitor can be mounted to the wooden or concrete wall with 4 screws and a pair brackets on the opposites. 142 5 71 342.9 140 5.
Customer panel material: 1. Wooden wall: Ø4.5mm thru holes for M4 screws w/nuts, or no thru holes, screws for wood 4mm. 2. Sheet metal: concealed head threaded studs M4 w/nuts. LA1950R/RTR/RTC/RTS RECOMMENDED CUSTOMER PANEL CUT-OUT 448.9 280 4R4 .6 -1 0 +1 385.5 -0 8 376.3 280 310.
IMPORTANT! The wall mounting instructions are for the qualified wall mounting person only! ! Warning! Please select the proper screws! The distance between the back cover surface and the bottom of the screw hole is 8 mm. Please use four M4 screws diameter with proper length to mount your monitor. Please note: the mounting stand must be able to support at least 13.2 lbs (6Kg). Connecting the Display (Figure 10.1) To setup this display, please refer to the following figure and procedures. 1.
(Figure 10.
User Controls Back Panel Controls Power Enter Down OSD Key Up Menu off status Menu on status Menu appear Menu disappear/return to main item Brightness Main item select up/Adjust up Contrast Main item select down/Adjust down Enter/Select sub-item function Power On/Off 11 Menu
How to Use the OSD Menus Icon key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the five functions in the main menus. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD. 5.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically. Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizontal size The screen image horizontal dot clock adjustment. Fine The screen image pixel phase adjustment.
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation" section. ► Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image.
Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card.
Product Dimensions 432.90 429.60 1.00 63.40 360.30 357.00 309.50 384.50 Side View Front View 100.00 Back View 16 100.00 75.00 132.50 75.
Compatibility Modes Mode Resolution H-Frequency(khz) V-Frequency(hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple MacII 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.08 72 VESA VGA 800X600 46.88 75 Apple Mac 832X624 49.72 75 VESA XGA 1024X768 48.36 60 VESA XGA 1024X768 56.48 70 VESA XGA 1024X768 60.02 75 VESA SXGA 1280X1024 64.
Touch Screen Driver Installation The LA1950RTR / LA1950RTC / LA1950RTS is available with both RS232 and USB connections. The touch driver is available online for these operating systems: Windows® 7, VISTA 64/32 bits, XP, 2000, ME, 98, NT4.0, CE, XP Embedded, Linux, Apple® Mac OS. Please Note: The LA1950RTR / LA1950RTC / LA1950RTS is Microsoft ® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface.
LA1950RTR / LA1950RTC / LA1950RTS Install Instructions: If you are using a PC running Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, follow the instructions below: 1. 2. 3. 4. Power on the PC. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display. Download the driver online and execute. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC running Windows® XP Embedded, follow the instructions below: Express: 1. Power on the computer. 2.
If you are using a PC running Windows® CE, follow the instructions below: 1. Power on the computer. 2. Make sure that the RS232 or USB cable is connected to the computer. 3. Using Platform Builder, build an image file by following the step-by-step instructions found in the folder file of the driver. If you are using a PC running Linux or Apple® Mac OS, follow the instructions below: 1. 2. 3. 4. Power on the computer. Make sure that the RS232 or USB cable is connected to the computer.
Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html.
Planar Systems, Inc. Customer Service 24x7 Online Technical Support: http://www.planar.com/support 1195 NW Compton Drive Beaverton, OR 97006-1992 Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day, 7 days a week © 2010 Planar Systems, Inc. 12/10 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
