Dome E2c Display Quick Reference Windows XP Windows 2000 020-0458-00A_3.
Read all instructions before setting up the Dome E2c display. Improper use of the display can result in electric shock, fire, or damage to display components. For more product information, go to www.planar.com/support.
Unpacking the Display Check the contents of your Dome E2c display package for all the items shown here. Save the original packaging materials for storage and shipping. Video card Dome E2c display Power adapter DVI cable Power cord Software CDs Also included: Composite Video, S-Video, and VGA cables. 3 020-0458-00A_3.
Display Components The high-bright UXGA 1200x1600 AMLCD panel is sized to a 541 mm (21.3 in.) display screen. The reset button, LED indicator, and input power and video ports are located on the back of the display. No other user-accessible controls are available. You can change the brightness of the Dome E2c display in the Display Properties dialog of the Windows operating system. However, when DICOM auto-calibration is running, you must control display brightness via the Dome CXtra software.
Legend 1 Reset. Restores default display setting. 2 LED indicator. Shows display status. 3 DIN 8-pin port. Drives power to the display. 4 S-Video, separate video 5 6 7 Back view 8 9 8 9 1 2 3 4 5 6 analog input port. Requires a 4-pin mini-DIN connector. C-Video, composite video analog input port. Requires an RCA or phono connector. DVI, DVI-I video input port. Supports DVI-D digital or DVI-A analog video. Requires DVI connector. VGA. VGA video analog input port.
Installing the Display Controller Remove any existing graphics card and its driver from your computer system before you install the controller and driver. Also disable any onboard graphics capability on the motherboard. See safety precautions on page 2. To install the controller 1 Turn off your computer and all peripherals. Disconnect all cables from your computer. Leave the power cord plugged into the grounded outlet. 2 Remove the computer cover.
Connecting the Display Use only the cables and power cord supplied with your display. To connect the display 1 Plug one end of the DVI signal cable to the DVI port on the display. Tighten the thumbscrews to secure the connection. 2 Plug the power cord into the power connector on the connector plate. 3 Plug the other end of the DVI cable into the video port on the installed controller. (Use DVI port #1 for Power cord the first display if you are installing only one display.
Installing the Display Driver Upon restarting your computer system, you must log on with administrator privileges. On Windows 2000 systems, Service Pack 4 or higher must be installed. To install the display driver 1 2 3 4 5 Start the system. Click Cancel on the Found New Hardware Wizard dialog box. Insert the Planar Installation CD and run the SETUP.EXE utility. Click Next on the Welcome dialog. Click Yes to the license agreement. The installation starts.
Adjusting the Display Properties Use the Display Properties dialog to make changes to the video settings or to set up dual-display configuration. To set the display orientation 1 Right-click the desktop and select Properties > Settings. 2 Select the monitor that you want to change. Then click Advanced. 3 Click the Monitor tab. Make sure the check box for Hide modes that this monitor cannot display is empty (unchecked). 4 Click the Rotation tab. • Check Standard Landscape for landscape mode.
Handling the Display • Set up your display on a stable, • • • • level surface away from any direct light or heat source, but near a grounded AC outlet. Choose a well-ventilated location with an adequate amount of space. Do not block the vents on the back of the display. Never lift the display by the desk stand. Use both hands to lift or move the display. Avoid touching the screen. Never apply pressure to the screen or touch the screen with bare fingers or with any objects.
Cleaning the LCD Screen Use a dry, clean, lint-free cotton cloth to remove surface dust from the display screen. Do not use chemically treated dust cloths. To remove grease or organic contaminants, follow this procedure: 1 Disconnect the power supply from the display. 2 Dampen a soft, clean cloth with a small amount of isopropyl alcohol. 3 Wipe the display screen gently with the dampened cloth. 4 Use a dry, clean, lint-free cotton cloth to wipe off the residue.
America Sales Planar Systems, Inc. 1195 NW Compton Drive Beaverton, OR 97006-1992 USA (503) 748-1100 phone (503) 748-1493 fax Medical Sales Planar Systems, Inc. 400 Fifth Avenue Waltham, MA 02451-8738 USA (781) 895-1155 phone (781) 895-1133 fax Customer Support Visit www.planar.com E-mail: medicalsupport@planar.com Call (866) PLANAR1 Europe Sales European Representative Planar Systems, Inc. Olarinluoma 9, P. O. Box 46 FIN-02201 Espoo, Finland + 358 9 420 01 phone + 358 9 420 0200 fax vertrieb@planar.
