LA1550TS USER MANUAL www.planar.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is registered trademark of Microsoft, Inc.
Table of Contents I. Usage Notice 4 Precautions II. 6 Package Overview 7 III. Installation 8 Product Overview 8 VESA Mount your Monitor 9 Connect the Display 10 Warning-Explosion Hazard 10 Special installation Instructions 11 IV. User Controls V.
I. Usage Notice Warning – Please do not open or disassemble the product as this may cause electric shock. This apparatus is suitable for use in Class I, Division 2 group A, B, C, D or unclassified locations. WARNING- EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS. AVERTISSEMENT – RISQUE D’ECPLOSION – AVANT DE DECONNECTER L’EEQUIPEMENT, COUPER LE COURANT OU S’ASSURER QUE L’EMPLACEMENT EST DESIGNE NON DANGEREUX.
Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Disconnect the power plug before cleaning Touch screen surfaces may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol. Use a soft cloth moistened with mild detergent to clean the display housing. Use only high quality and safety approved AC/DC adapter.
II.
III.
VESA Mount your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Connecting the Display To setup this display, please refer to the following figure and procedures. 1. Be sure all equipments are turned off. 2. Connect the Paint Booth Cable to the connector on the back cover of the monitor. 3. Connect the Extension Cable to the Paint Booth Cable and the other end to PC. 4. Connect D-SUB connector from the extension Cable to VGA output connector on PC. 5.
Warning-Explosion Hazard Do not disconnect equipment unless power has been switched OFF or the area is known to be non-hazardous. Special installation Instructions Install system as per diagram above by qualified personnel in accordance with NFPA 70 (NEC) Article 500 (contact an electrician if you have any questions or concerns about the installation).
IV. User Controls Front Panel Controls No Icon Control Function 1. Menu Menu button Display/Exits the OSD menu 2. ▲ Brightness 1. Enter brightness of the OSD. 2. Increase value of the adjustment item. 3. Select item clockwise. Plus Clockwise 3. ▼ Contrast Minus 1. Enter contrast of the OSD. 2. Decrease value of the adjustment item. 3. Select item counter-clockwise CounterClockwise 4. Select Select Auto Adjust Select: Select the adjustment items from OSD menu.
How to Use the OSD Menus 1. 2. 3. Press the "MENU" button to pop up the "on-screen menu" and press "▼" or "▲" to select among the four Main Menus. Choose the adjustment items by pressing the " SELECT / AUTO " button. Adjust the value of the adjustment items by pressing the "▲" or "▼" button. (1) The OSD menu will automatically close, if you have left it idle for a pre-set time.
On-Screen Display Menus Main OSD Menu: MAIN MENU Control Function Contrast 0-100 Adjusts the maximum luminance level of the monitor. Brightness 0-100 Adjusts the backlight of the monitor. Auto Adjust No/Yes The screen is moved horizontally right and left (1 pixel pitch increment.) Left / Right 0-100 The screen is moved horizontally right and left (1 pixel pitch increment.) Down / Up 0-100 The screen is moved vertically up and down (1 line increment.
V. Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation" section. ► Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image.
Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the LCD Display has been powered on but it cannot receive any signal from the computer graphics card.
Product Dimensions LA1550TS User Manual 16
Compatibility Modes Mode Resolution H-Frequency (KHz) V-Frequency (Hz) VGA 720 x 400 31.47 70 VGA 640 x 480 31.47 60 MAC XGA 640 x 480 35 66 VESA VGA 640 x 480 37.86 72 VESA SVGA 640 x 480 37.5 75 VESA SVGA 800 x 600 35.16 56 VESA SVGA 800 x 600 37.88 60 VESA SVGA 800 x 600 46.88 75 VESA XGA 800 x 600 48.08 72 MAC XGA 832 x 624 49.72 75 VESA XGA 1024 x 768 48.36 60 SUN XGA 1024 x 768 52.45 66 VESA XGA 1024 x 768 56.48 70 VESA XGA 1024 x 768 60.
Manufacturer’s Instructions This apparatus is suitable for use in Class I, Division 2 groups, or unclassified locations. Control drawing: WARNING: EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEALING PROPERTIES OF MATERIALS USED IN THE DEVICES. WARNING: EXPLOSION HAZARD. DO NOT DISCONNECT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOWN TO BE FREE OF IGNITIBLE CONCENTRATIONS.
Compliance Information Federal Communication Commission Radio Frequency International Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference with the equipment is operated in a commercial environment.
Revision Control DATE: DESCRIPTION: Oct 2009 Document number 020-0996-00 Rev. A June 2011 Document number 020-0996-00 Rev. B Planar Systems, Inc. Corporate Headquarters 1195 NW Compton Drive Beaverton, OR 97006-1992 Planar Customer Support Telephone: US: 1-866-PLANAR1 (866) 752-6271 Outside US: (503) 748-5799 E-mail: PlanarSupport@planar.com Online Technical Library: http://www.planar.com/support Hours: M-F, 3am-7pm ET, 11am-3am GMT © 2008 Planar Systems, Inc.
