PT2245PW Touch Screen Monitor USER’S GUIDE www.planar.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc.
Table of Contents Usage Notice Precautions.................................................................................................................. 1 Introduction About PT2245PW Series.............................................................................................. 2 Touch Screen for PT2245PW ....................................................................................... 2 Package Overview ........................................................................................
Usage Notice ! ! Warning - To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: • Turn off the product before cleaning.
Introduction About PT2245PW Series The PT2245PW Series is a 21.5" flat panel screen with an active matrix, thin-film transistor (TFT) edge-lit LED LCD. This unit is to be used as commercial and light industrial equipment only. Features include: • Direct Analog signal input • Direct Digital signal input • Active matrix TFT LCD technology • 1920 x 1080 resolution • 21.5" viewable display area - 16:9 aspect ratio • 31.47 ~ 82.3 KHz horizontal scan • 56 ~ 75 Hz high refresh rate • 0.24795mm x 0.
Package Overview LCD Display USB Cable ( A to B) Power Cord VGA Signal Cable DVI-D Cable DC Power Supply Landing Strip Cable Cover Screw xxxxxxxxx xxxxxxxxx / xxxxxxxxx USER’S GU IDE www.planartou ch.
Installation Product Overview • Front View • Bottom View (Without Stand) VGA DVI RJ-Type 4 DC IN USB
VESA Mount for Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a UL certified swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Start Your Installation Please follow these instructions so that you can hook up the cables to associated connectors. 1. 2. 3. 4. 5. Lay the display flat on an even surface. Move the stand into position as seen in the step 1 diagram. Remove the cable cover as seen in the step 2 diagram. Connect the cables to the appropriate connectors as seen in the step 3 diagram. Re-attach the cable cover.
Connecting the Display (Figure 8.1) To setup this display, please refer to the following figure and procedures. 1. 2. 3. 4. 5. 6. ! Be sure all equipment is turned off. Connect the DC plug to the power connector on the monitor and the other end into an electrical outlet (8.1). Connect the D-SUB or DVI cable from the display’s D-SUB or DVI input connector to the D-SUB or DVI connector of your host computer and tighten the screws (8.1).
(Figure 8.
User Controls Side Panel Controls Icon Key Name Menu Up Down Select Power OSD Key Menu off status Menu on status Menu appear Menu disappear / return to main item Brightness Main item select up / Adjust up Contrast Main item select down / Adjust down Select sub-item function Power On / Off 9
How to Use the OSD Menus Icon Key Name Menu Up Down Select Power 1. Press the “Menu” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the five functions in the main menu. 2. Choose the adjustment items by pressing the “Select” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on the screen, press the “Menu” button to return to the main menu or to exit OSD. 5.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically. Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizontal size The screen image horizontal dot clock adjustment. Fine The screen image pixel phase adjustment.
Appendix Troubleshooting If you are experiencing trouble with the display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section. ► Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image.
Warning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and VGA/DVI signal cable.
Product Dimensions 517.4 mm 46.0 mm 212.0 mm ► Side View 249.6 mm 219.0 mm ► Top View 14 351.7 mm 313.
Rotate 313.3 mm 517.4 mm 553.7 mm ► Front View 46.0 mm 212.0 mm ► Side View 249.6 mm 219.
Compatibility Modes Mode Resolution H-Frequency(khz) V-Frequency(hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple MacII 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA SVGA 800X600 35.16 56 VESA SVGA 800X600 37.88 60 VESA SVGA 800X600 48.08 72 VESA SVGA 800X600 46.88 75 Apple Mac 832X624 49.72 75 VESA XGA 1024X768 48.36 60 VESA XGA 1024X768 56.48 70 VESA XGA 1024X768 60.02 75 VESA SXGA 1280X1024 64.
Touch Screen Driver Installation The is available with USB connection. The touch driver is available at www.planar.com/support for these operating systems: Windows® 7/8, VISTA, XP, 2000, CE, XP Embedded, Linux kernel 2.6.x (32 bit & 64 bit), Apple® Mac OS. (Windows 7/8 Multi touch without driver) Please Note: 1. The PT2245PW is Microsoft® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface.
PT2245PW Calibration Instruction: Calibrating the touch screen in Windows 7/8: 1. Tap the Start button, Control Panel and then Hardware and Sound. 2. Under Tablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Yes to allow the program to make changes. 4. Follow the on-screen instructions to calibrate the touch screen.
19
PT2245PW Install Instruction: If you are using a PC running, Windows® 7/8, VISTA, XP, 2000, follow the instructions below: 1. 2. 3. 4. Power on the PC. Make sure that the USB cable is connected to the computer. Visit www.planar.com/support. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC running driver Linux kernel 2.6.x (32 bit & 64 bit), follow the instructions below: 1. 2. 3. 4. Power on the PC. Make sure that the USB cable is connected to the computer.
Technical Support Cables and Accessories To find cables and accessories for your Planar monitor, touch screen or other Planar products visit our online store at www.PlanarOnline.com. Technical Support Visit Planar at http://www.planar.com/support for operations manuals, touchscreen drivers, warranty information and access to Planar’s Technical Library for online trouble shooting.
Planar Systems, Inc. Customer Service 24x7 Online Technical Support: http://www.planar.com/support 1195 NW Compton Drive Beaverton, OR 97006-1992 Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day, 7 days a week © 2013 Planar Systems, Inc. 10/13 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
