IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment: Model #: __________________________ Service & Parts Manual Covering the SPINFRESH Option for Solstice Fryers TM L22-375 Rev 1 6/13 ENGLISH Serial #: __________________________ Date Purchased: ___________________
FOR YOUR SAFETY DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. Do not spray aerosols in the vicinity of this appliance while it is in operation. WARNING Improper installation, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
WARNING The oil/shortening level should NOT fall below the minimum indicated level line at any time. The use of old shortening can be dangerous as it will have a reduced flash point and be more prone to surge boiling. WARNING The contents of the crumb catch and/or filter pan of any filter system must be emptied into a fireproof container at the end of the frying operation each day. Some food particles can spontaneously combust into flames if left soaking in certain oil/shortening materials.
TABLE OF CONTENTS 1 Fire Safety Systems ------------------------------------------------------------------------------------------------------------------------- 5 2 Operation --------------------------------------------------------------------------------------------------------------------------------------- 5 3 Troubleshooting ------------------------------------------------------------------------------------------------------------------------------- 5 4 Basket Engagement -----------------------
1 Fire Safety Systems If your appliance is equipped with SPINFRESHTM, the tank enclosure can interfere with the performance of preexisting fire safety systems. Modifications to the fire safety system should be performed by a professional who is qualified in installing, designing and maintaining your fire safety system prior to operating any SPINFRESHTM appliance. WARNING Replacing or adding appliances under a pre-existing fire safety system may require modifications to the system.
4 Basket Engagement This procedure is to check the basket engagement during the spin cycle and make any adjustments if required. WARNING Oil/shortening must completely cover the heat tubes or heating elements at all times while appliance is on. Press to turn the appliance ON. Press Press to raise the basket to the highest position. Check the basket drive pin’s location within the drive coupling. Adjust basket drive pin position as described if required.
NOTICE Do NOT rotate the proximity switch during this procedure. The rotation of the switch is critical to accurately sensing the basket lift position. If the basket drive pin position needs adjustment. While holding the upper proximity switch in place, use a small screwdriver to loosen screw on the switch. Move the switch up and down to adjust the upper position. Move the proximity switch the same distance that the basket pin is away from its ideal location.
5 Field Upgrade In February of 2013, various improvements to the SPINFRESHTM option were made available as a field upgrade kit. Refer to the diagram below to identify if the appliance has been upgraded or not. If the appliance can be upgraded, contact the factory to order the appropriate upgrade kit. Upgrade kit part numbers: Kit No.
6 Basket Lift Relay Logic Relay K1 K2 K3 K4 Controlled by Spin (Upper) Position Proximity Switch Cook (Lower) Position Proximity Switch K4 Relay Signal from the I‐12 Computer Switches Signal to the I‐12 computer Signal to Basket lift driver board Signal to the I‐12 computer Signal to Basket lift driver board Electrically Brakes the actuator movement Start signal to the basket lift driver board K3 Relay 7 SPINFRESH Diagnostic Mode Spin Diagnostics Step 1. Enter Factory Programming Step 2.
8.1 Superseded basket Lift Assembly built before September 2012 See next page for parts list.
Superseded Basket Lift Assembly built before September 2012 ITEM # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 25 26 27 PART NO. A5625802 A5625901 A5626002 PP10429‐M PP11068 60134001 60134305 60174101 60174001 A5626202 60136901 A5626302 PP10686 PP10266 60177502 PP10674 PP10689 PP10023 P0113300 PP10693 P0093300 P6071140 A5626102 A5626104 DESC.
8.2 Basket Lift Assembly built after September 2012 See next page for parts list.
Basket Lift Assembly built after September 2012 B56092xx, Complete assembly ITEM NO. PART NO. 1 A5625802 2 700324-10 LABEL, SCHEMATIC WIRING SG,SE SPINFRESH 1 3 A5626002 1 4 DESCRIPTION BASKET LIFT, BOX BASKET LIFT, BOX COVER ACTUATOR MODULAR SG PP10429-M TRANSFORMER, 80VA 120-208-240V TO 24V MCI QTY 1 1 5 PP11068 RELAY, 24VDC DPDT WITH MOUNTING TABS 4 6 60134001 CNTRL,BASKT LIFT DRIVER BOARD 1 7 60134305 ACTUATOR, 25 3.3-9.
8.3 Superseded Enclosure Assembly built before September 2012 See next page for parts list.
Superseded Enclosure Assembly built before September 2012 ITEM # PART NO.
8.4 Enclosure Assembly built after September 2012 See next page for parts list.
Enclosure Assembly built after September 2012 B33354xx, Complete assembly DESCRIPTION SG14 SE14 S*H50 SSH55 ITEM NO. PART NO.
8.5 Superseded Cover & Damper Assembly built before September 2012 ITEM NO. 1 2 3 3 3 PART NO.
8.6 Cover Assembly built after September 2012 ITEM NO. 1 2 3 4 5 PART NO. DESCRIPTION SG14 SE14 S*H50 SSH55 B2104901 TANK COVER, WELDMENT SG14* B2104902 TANK COVER, WELDMENT SE14 B2104903 TANK COVER, WELDMENT S*H50 X B2105001 TANK COVER, BACK SUPPORT WELDMENT S*14 SPIN X X B2105002 TANK COVER, BACK SUPPORT WELDMENT S*H50 SPIN 60135702 BOLT, 10-24 X .
8.7 Miscellaneous Parts ITEM NO. PART NO. 1 2 3 4 5 6 7 8 B5609901 B5609902 B5609903 B5609904 60088003 A5624902 A3366502 A3366504 60176901 60176902 B2104702 B2104701 DESCRIPTION BASKET LIFT, TOP PLATE ASSEMBLY SG14R, SSH55 BASKET LIFT, TOP PLATE ASSEMBLY SG14 BASKET LIFT, TOP PLATE ASSEMBLY SE14 BASKET LIFT, TOP PLATE ASSEMBLY S*H50 SCREW, .250‐20 X .
8.8 Basket Assembly B4516001 Entire assembly (Blue Handle) ITEM NO. PART NO. DESCRIPTION 1 B4515303 WIRE GOODS, BEARING BASKET HANDLE WELDMENT BLUE 2 B4515304 WIRE GOODS, BEARING BASKET HANDLE WELDMENT GREEN 3 60183801 TAPERED ROLLER BEARING ASSEMBLY, BEARING 1.375 O.D. X .500 I.D. 4 60183901 TAPERED ROLLER BEARING ASSEMBLY, OUTER RING (RACER) 1.375 O.D. X .500 I.D. 5 60183501 NUT, SLOTTED HEX (CASTLE) .50-13 THREAD 6 6NT202 PIN, SST COTTER .125 DIA. X 1.25 LG.
8.9 Bottom Assembly B5608802 Entire assembly ITEM NO. PART NO. DESCRIPTION 1 PP10665 SCREW,10-24 X .375 RDH SST 2 60088013 SCREW, 10-24 X .625 HEX HEAD SST 3 60088012 SCREW, 10-24 X .375 HEX HEAD SST 4 60177401 SCREW, OVAL 82 DEG X .375 SST 5 B5609001 LIFT PLATE 6 A5625402 LIFT PLATE, PIVOT BAR 7 A5625302 LIFT PLATE,BLOCK 8 A5625502 LIFT PLATE STOP 9 60022906 WASHER, FLAT #10 X 1.00 X .
8.10 Splash Back Assembly B41043xx Entire assembly ITEM NO. PART NO.
9 Basket Lift Wiring Diagram L22-375 Rev 1 6/13, Page 24
10 Schematic L22-375 Rev 1 6/13, Page 25
Notes: L22-375 Rev 1 6/13, Page 26
Notes: L22-375 Rev 1 6/13, Page 27
In the event of problems with or questions about your order, please contact the Factory at: +001 (603) 225-6684 (World Wide) In the event of problems with or questions about your equipment, please contact the Pitco Authorized Service and Parts representative (ASAP) covering your area, or contact Pitco at the number listed to the left. MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501 SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301 SPINFRESHTM is a trademark of Spinfry inc.
