Instructions / Assembly
53
6. Retirez le capuchon protecteur en plastique de la valve du cylindre.
7. Vérifiez que le tuyau ne contient pas de plis, qu'il ne touche pas les bords tranchants et qu'il n'entrera pas en contact avec
des surfaces qui pourraient devenir chaudes pendant l'utilisation.
8. Tenir le régulateur et insérer le mamelon en laiton dans la sortie de la valve du réservoir de GPL. Assurez-vous que le
périphérique est correctement centré.
9. Tournez le grand écrou d'accouplement dans le sens des aiguilles d'une montre à la main et serrez à fond. Veillez à ne pas
visser l'écrou d'accouplement dans la valve du cylindre. N'utilisez pas d'outils pour resserrer la connexion. Remarque: Si vous
ne parvenez pas à établir la connexion, répétez les étapes 7 et 8.
INSTRUCTION D'ÉCLAIRAGE :
• LIRE TOUTES LES INSTRUCTIONS AVANT D'ALLUMER.
• PORTE OUVERTE PENDANT L'ÉCLAIRAGE.
• VANNE PRINCIPALE À GAZ OUVERT.
• POUSSER ET TOURNER LA SOUPAPE DU BRULEUR DANS LE
SENS INVERSE EN POSITION "HAUTE"
• APPUYER SUR LE BOUTON DE L'ALLUMEUR JUSQU'AU
BRÛLEUR DU BRÛLEUR.
• SI L'ALLUMAGE NE SE PRODUIT PAS DANS LES 5 SECONDES,
METTEZ LES VANNES EN POSITION "OFF",
ATTENDEZ 5 MINUTES ET RÉPÉTEZ LA PROCÉDURE D'ÉCLAIRAGE.
Remarque : Utilisez les trous de visualisation sur les côtés du
panneau de support du fumoir pour vous assurer que les
flammes des deux brûleurs sont allumées.
INSTRUCTIONS D'UTILISATION DE LA FLAMME :
• METTRE LA SOUPAPE DU BRÛLEUR EN POSITION "BAS" SI NÉCESSAIRE.
• TOURNER LA SOUPAPE DU BRÛLEUR "HAUTE POSITION" SI NÉCESSAIRE.
• METTRE LA SOUPAPE DU BRÛLEUR SUR "OFF" SI POSSIBLE.
Instructions d'utilisation du système à double brûleur
Votre fumoir à gaz Pit Boss a été conçu avec un système de contrôle à soupape unique / double brûleur. Le brûleur supérieur est un
brûleur de fumée BTU faible et le brûleur inférieur est un brûleur principal BTU plus élevé. Ce qui suit est l'opération recommandée:
1. Lorsque le bouton de commande est réglé sur "HIGH", les deux brûleurs s'allument. Cela vous donnera la fumée de votre
plateau de copeaux de bois le plus rapide et aussi vous donner les plus hautes températures à l'intérieur de votre fumeur.
2. Lorsque le bouton de commande est réglé sur le réglage "MED", les deux brûleurs sont toujours allumés. Le brûleur principal
est sur la plage de température intermédiaire à l'intérieur de votre fumoir.
'
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
---------------------------------
------------------------------------
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
Brûleur principal
Brûleur de fumée
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
---------------------------------
------------------------------------
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
---------------------------------
------------------------------------
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
---------------------------------
------------------------------------
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
---------------------------------
------------------------------------
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
---------------------------------
------------------------------------
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
wood chips tray the fastest and also give you the Highest Temperatures inside your smoker.
2019
17
Operating Instructions
Operating Instructions
18
LIGHTING INSTRUCTION:
READ ALL INSTRUCTION BEFORE LIGHTING.
OPEN DOOR DURING LIGHTING.
OPEN CYLINDER MAIN GAS VALVE.
PUSH AND TURN BURNER VALVE COUNTER-CLOCKWISE TO
TO “HIGH” POSITION " ".
PUSH IGNITOR BUTTON UNTIL BURNER IGNITES.
IF IGNITION DOES NOT OCCUR WITHIN 5 SECONDS, TURN VALVES
O
TO OFF POSITION " ", WAIT 5 MINUTES, AND REPEAT
LIGHTING PROCEDURE.
•
•
•
•
•
•
Install LP-Cylinder
on the unit as
shown below
OPERATING INSTRUCTIONS
Operating Instructions for Dual Burner System
Your Pit Boss Gas Smoker was designed with a
Single Valve Control/ Dual Burner System. The
Top burner is a low BTU smoke burner and the
bottom Burner is a Higher BTU main burner. The
following is the recommended operation:
1. When the control knob is set to the
setting, both burners lit. This will give you smoke from your
HIGH
2. When the control knob is set to the MED setting, both burners are still lit. The main Burner is on
3. When your control knob is set to the “Low”
automatically Shut off. This will give you smoke from your wood chips tray in approx. 10min depending on how long you
soaked your wood chips. This will also give you lowest temperature inside your smoker.
4. If you have your control knob set on “Low” setting and desire higher temperature, you must rotate your control knob
90 degree to the “MED” setting to the “High” setting.
FLAME OPERATION INSTRUCTIONS:
TURN BURNER VALVE TO “LOW” POSITION " " IF NEEDED.
TURN BURNER VALVE “HIGH” POSITION " " IF NEEDED.
TURN BURNER VALVE “OFF” POSITION " ". IF NEEDED.
O
•
•
•
Note: Use the viewing holes on the sides of the smoker
Support Panel to make sure both burners flames are lit.
Smoke Burner
Main Burner
-------
-----------
Low
setting, only the smoke burner will be lit. The main burner will
---
HIGH setting
Med
the “Low” setting and the smoke burner is on. This will give you smoke from your wood chips tray quickly and give you the
intermediate temperature range inside your smoker.
--
---
LP Cylider Capacity and Specifications:
The 20 lb (9.1 kg). LP cylinder used with this smoker must conform to the following requirements.
Diameter- 12” (30.5cm)
Height 18” (45.7cm)
WARNINGS
•
Keep the fuel supply hose away from any heated surface
• The use of alcohol, prescription or non-prescription drugs may impair the consumer's ability to
properly assemble or safely operate the appliance.
• Cylinders must be stored outdoors out of the reach of children and shall not be stored in a building,
garage or any other enclosed area.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from
hot surfaces.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The pressure regulator and hose assembly supplied with the appliance must be used. Replacement
pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
----
--
-
-
-
---
-
-
-
-
-
-
-
-
-
--
----
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
--
-
-
---
-
-
-
--
-
-
-
--
-
--
Important Note: If you need to replace or reinstall the
burner, make sure the valve tip is completely inside
burner venturi at end of burner as shown. Failure to
follow these instructions could result in fire or
explosion which could cause property damage,
personal injury or death.
Installez le cylindre
LP sur l'unité comme
indiqué ci-dessous.