Instructions / Assembly

ManualsBrandsPit Boss ManualsGrills700SC Pellet Grill in Black

Section One: ASSEMBLY INSTRUCTIONS

ASSEMBLING THE LEG KIT

Page 7

Tools Required:

Installation:

Step 1 Attach bottle opener to the leg

Step 2 Attach casters to the legs

The bottom portion of all the legs, 3 x #9 and 1 x #10, have a threaded plate

installed to allow for the two (2) locking and two (2) non-locking casters to be

easily installed.

 Hand install the casters on the 4 (four) legs.

 Using your 1/2” wrench, turn each of the casters in a clockwise

direction into the bottom leg plate. Turn ALL the way in.

Step 3 Attach legs to bottom shelf

To ease installation, assemble the entire cart components on a raised work

bench or flat surface. You will require all 4 legs c/w casters, #9 & #10, the

bottom shelf, #11, and 8 x screws 1/4”-20 (AA).

 Ensure that the shelf is facing with the flat surface facing upwards.

 Begin by carefully sliding leg # 10, with the bottle opener, into the

correct cut-out, front right hand side, ensuring the screw hole

patterns match.

NOTE: It is best to start each threaded screw by hand, to ensure

the thread DOES NOT cross thread or strip.

 Hand start two (2) of the screws (AA), into the leg, then secure

firmly in place, using the screw driver.

 Repeat, the above steps, to secure the remaining 3 legs.

Parts Needed:

3 x # 9 Legs

1 x #10 Leg c/w Bottle Opener Mounting

1 x #11 Bottom Cabinet Shelf

4 x #13 Casters

1 x #12 Bottle Opener

16 x Screws 1/4” - 20 (AA)

2 x Screws 5/32

#9 3 x legs

#10 1 x leg w/ extra holes

#13 4 x Casters

#11 Bottom Shelf

To reduce frustration later, start by locating leg #10, the only leg with two extra

screw holes, on the front as well as on the side.

 Using 2 x screws 5/32 and your Phillips driver carefully hand-start

each screw through the opener and into the clinch nuts, then secure

bottle opener # 12 in place.

1—1/2” Open End Box Wrench

1– Adjustable Crescent Wrench

1– Phillips Screwdriver

Your Pit Boss grill comes complete with the all important bbq necessity, a bottle

opener, #12. “Use Responsibly”

#10 1 x leg

w/ extra holes

Summary of content (10 pages)

PAGE 1
Section One: ASSEMBLY INSTRUCTIONS ASSEMBLING THE LEG KIT Parts Needed: 3 1 1 4 1 16 2 x # 9 Legs x #10 Leg c/w Bottle Opener Mounting x #11 Bottom Cabinet Shelf x #13 Casters x #12 Bottle Opener x Screws 1/4” - 20 (AA) x Screws 5/32 #13 4 x Casters #9 3 x legs #10 1 x leg w/ extra holes Tools Required: #11 Bottom Shelf 1—1/2” Open End Box Wrench 1– Adjustable Crescent Wrench Or 1– Phillips Screwdriver Installation: Step 1 Attach bottle opener to the leg Your Pit Boss grill comes complete with th
PAGE 2
Section One: ASSEMBLY INSTRUCTIONS ATTACHING LEG AND GRILL ASSEMBLY: - for S models only Note: If you have the Pit Boss Model SC, that comes complete with the Cart Enclosure kit, please proceed to the next page. Hardware Required: 1 1 x Completed Leg Assembly x # 4 Pit Boss Main Body 16 x Screws 1/4” - 20 (AA) Tools Required: 1– #2 Phillips Screwdriver Installation Steps WARNING! NOTE: Due to the size and weight of the upper grill, the following installation step is a two (2) person job.
PAGE 3
Section One: ASSEMBLY INSTRUCTIONS ATTACHING ENCLOSURE KIT TO THE UNIT: (models SC only) Hardware Required: 1 2 1 or 2 2 or 4 1 or 2 1 1 1 x x x x x x x # 19 # 20 # 21 # 22 # 23 #24 #25 Rear Panel Side Panel Door Panel or Panels Handle Bezels 7 1/4” Handle or Handles Bottom Door Stop Top Door Magnet - Hardware Package # (for Enclosure Kit) 16 x 5/32 Screws Tools Required: # 25 Magnetic Door Stop 1– #2 Phillips Screwdriver Installation Steps To ease installation, assemble the majority of the encl
PAGE 4
Section One: ASSEMBLY INSTRUCTIONS ATTACHING ENCLOSURE KIT TO THE UNIT: Installation Steps (models SC only) Step 2 Attach Side Panels: You will require the 2 x Side Cart Panels and 8 x 5/32 screws. Both Side Panels are identical.  Install the right hand side panel first. The exterior of the panel will be flush with the outside edge of the legs and the bottom shelf.  Line up the four (4) pre-drilled screw holes on the sides of the legs, with the holes on the side of the panels.
PAGE 5
Section One: ASSEMBLY INSTRUCTIONS ATTACHING ENCLOSURE KIT TO THE UNIT: (models SC only) Installation Steps Step 5 Attach The Door Handle - Single or Double Door You will require the Front Door panel(s)(#21), Door Handle (s) (#23), door handle bezels (#22), and 2 x 5/32 screws.        Insert screw through the rear of the door panel. Place bezel over the protruding screw. Place handle over the screw and bezel. Begin to secure screw to the handle.
PAGE 6
Section One: ASSEMBLY INSTRUCTIONS ASSEMBLING THE REMAING COMMON COMPONENTS ASSEMBLING THE LID HANDLE Parts Needed: 5 6 Lid Handle Decorative Washers x 2 ( Bezels ) Insulation Cardboard Hardware Required: Screw 1/4”- 20* 3/5” x 2 (AA) Installation Steps      Insert one screw (A) from inside the lid, through the hole provided in the lid. Place one Bezel (6) over the screw, then line-up the handle (5) with the threaded end of the screw.
PAGE 7
Section One: ASSEMBLY INSTRUCTIONS INSTALLING THE SOLID SIDE SHELF: Parts Required: 1 x #20 Side Shelf—Black—Solid Side Shelf 4 x #21 Side Shelf—Tool Hanger w/ nuts 1 x #22 Side Shelf— 10“ Long Chrome Hanger Bar w/screws 4 x Multi-Head Screws (AA) Tools Required: Large Phillips Screwdriver or Phillips Drive Bit and Drill Installation: Step 1 # 21 Tool Hangers  Remove the nuts from all four (4) tool hangers.  Insert individual tool hanger into the four (4) holes provided in the side shelf top, # 20.
PAGE 8
Section One: ASSEMBLY INSTRUCTIONS PLACING THE COOKING COMPONENTS COOKING GRIDS (2) Your Pit Boss grill comes with Cast Iron main cooking grids. Cast Iron is an excellent heat absorber and is still the best way to produce those “steak house’ sear markings. NOTE: To maintain the searing and grilling performance of your cooking grids, as well as their longevity, some special care and maintenance Is required as with any cast iron cooking tools.
PAGE 9
Section One: ASSEMBLY INSTRUCTIONS INSTALLING THE GREASE TRAY Parts Needed: 1 1 x # 14 Chrome Handle x # 15 Grease Tray Tools Required: 1– Phillips Screwdriver Grease Drawer  Remove the two (2) screws from the bar hanger.  Insert the screws through the two (2) holes provided in the front of the grease tray # 15.  Using a Phillips screwdriver to tighten to a snug, secure fit.  Simply slide the drawer into the opening supplied.
PAGE 10
Section One: ASSEMBLY INSTRUCTIONS HOOKING UP TO POWER NOTE: Before plugging your Pit Boss into any electrical outlet ensure the Temperature Dial is in the “OFF” position. AT HOME  This appliance requires 110 Volt, 60Hz, 5 amp service.  It must use a 3 prong grounded plug.  The control uses a 5 amp 120Volt Fast-Blow fuse to protect the board from the igniter. GFI Outlets  This appliance will work on most GFI Outlets. Recommended size 15 amp.