Manual

CUP SEAL & VALVE REMOVAL
VALVE REMOVAL CONTINUED
19
20
Figure 27
Figure 28
1/8"
Allen
Screw
1/8" Allen Screw
BottomLine
ASA
WWAA RR NN II NN GG
DO NOT ATTEMPT TO COMPLETELY DISASSEMBLE YOUR PIRANHA
®
UNLESS QUALIFIED TO DO SO.
CONTACT KEE FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED KEE
PIRANHA
®
REPAIR FACILITIES. PHONE: [phone] WEB: KEEACTIONSPORTS.COM
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED ONLY WITH THE CORRECT
PRESSURE RATED COMPONENTS.
3. To remove the bottom line air system, detach the bottom line ASA from the grip by removing the two
screws (#42). See Figure 27. The 5/32” allen wrench for this procedure is not included with the marker.
Then unscrew the vertical grip (#40) or regulator.
Figure 29 Figure 30
5. To access the valve, use a flathead screwdriver to remove the small brass screw located in the
center of the underside of the receiver (#26). See Figure 29. To remove the valve body, use a
flat ended wooden dowel or the eraser end of a pencil to push the valve body out of the front
of the receiver. See Figure 30.
Questions about the operation of the KEE Piranha
®
paintball marker may be directed to: KEE Action Sports,
570 Mantua Blvd., Sewell, NJ 08080 USA; phone: [phone] or keeactionsports.com for any updates
regarding your Piranha
®
purchase.
6. The valve body must be inserted correctly with the raised flat surface of the valve and larger hole pointing
towards the front of the marker. Be careful reinserting the valve body. Any scratches to the front can cause
leaks. Use a flat ended wooden dowel or the eraser end of a pencil to push the valve body into the front
of the receiver. See Figure 31. The valve pin assembly must be inserted correctly into the valve; valve pin
must drop down into valve body completely.
Figure 31
NOTE: Make sure marker is un-cocked before continuing to step 4.
4. To remove trigger frame from the receiver, remove the two 1/8” socket allen screws (#29) under
the receiver. One is in front of the trigger guard and one is behind the grip portion of the
frame. See Figure 28. The receiver then will disassemble from the trigger frame.
IMPORTANT: Valve body O-rings and front valve portion of the receiver
must be well oiled prior to valve body insertion.
1. Before disassembling the marker remove the air source, then remove all paintballs from the marker,
barrel, and loader.
2. Unscrew the ASA Slug to access
the cup seal assembly. See Figure
25. Remove the valve spring, cup
seal assembly, and guide as in
Figure 26.
Figure 26Figure 25
DO NOT ATTEMPT TO PERFORM MAINTENANCE PROCEDURES UNLESS QUALIFIED TO DO SO.
THIS TROUBLESHOOTING GUIDE DOES NOT COVER ALL SITUATIONS AN INDIVIDUAL MAY ENCOUNTER.
CONTACT KEE FOR REPAIR ASSISTANCE AND INFORMATION REGARDING AUTHORIZED KEE PIRANHA
®
REPAIR
FACILITIES. PHONE [phone] WEB KEEACTIONSPORTS.COM
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED WITH THE CORRECT PRESSURE
RATED COMPONENTS.
BEFORE DISASSEMBLY OF THE MARKER, REMOVE AIR SOURCE; REMOVE ALL PAINTBALLS FROM THE MARKER, BARREL, AND LOADER.
TO CHECK IF THE MARKER IS UNLOADED: REMOVE AIR SYSTEM AND SHOOT MARKER IN A SAFE DIRECTION.
REMOVE HOPPER, VISUALLY INSPECT CHAMBER FOR A PAINTBALL, REMOVE AND INSPECT BARREL FOR THE PRESENCE OF A PAINT-
BALL. NEVER LOOK DOWN THE BARREL OF ANY PAINTBALL MARKER ONCE THE BARREL IS SCREWED INTO THE MARKER.
THE PAINTBALL MARKER AIR SYSTEM MUST BE REPAIRED OR REPLACED WITH THE CORRECT PRESSURE RATED COMPONENTS.
WWAA RR NN II NN GG
Manual_Piranha_5.5_eng.qxd 11/16/07 1:57 PM Page 14